2015 PEUGEOT BOXER clock

151
Halogen bulbs must be changed after
the headlamp has been off for several
minutes (risk of serious burns). Do not touch
the bulb directly with your fingers, use a
lint-free cloth.
When each operation has been completed,
check the operation of the lamps.
5 - Front foglamps
type E, H1

1 - 55 W
-


t
urn the steering so that the wheel
on the side in question is turned fully


inwards.
-
Remove the screw located in the wheel
arch.
-
Remove the protective cover.
LE
d daytime running lamps
these light-emitting diode (LeD) lamps


serve as both daytime running lamps and
sidelamps.
If your vehicle is fitted with L
eD daytime


running lamps, contact a P
eugeOt dealer.
4 - Sidelamps / daytime running lamps
type A, W21/5W - 21W and 5W
-
Remove the cover by pulling on the
rubber tongue.
-


t
urn the bulb holder a quarter of a turn
anti-clockwise.
-
Change the bulb.
-
Remove the fixing clip and disconnect
the electrical connector
.
-


t
urn and disengage the bulb holder.
-
Change the bulb taking care to align the
metal part with the grooves on the lamp.
QuICK HeLP
8
Failed bulb or lamp

157
● For versions with alloy wheels, remove
the three fixing screws I from the
strap
j.
●
Remove the assembly from inside the
alloy wheel.
Spare wheel
the spare wheel retaining bolt is located
below the bumper on the right.
-
Install the long socket A , the


wheelbrace
d and the bar B on the


retaining bolt.
-


t
urn the assembly anti-clockwise to
lower the wheel.
-


t
urn to the full extent, indicated by an
increase in the force required.
-
Having fully unwound the cable, take out
the spare wheel under the vehicle. ●
For versions with steel wheels, unscrew
the grip
G.
●
Remove the carrier H from the outer part


of the steel wheel.
-
Release the spare wheel and place it
near the wheel to be changed.
-
If possible, place a chock against the
wheel diagonally opposed to the wheel


to be changed.
QuICK HeLP
8
Puncture

160
Refer to the "technical data -
Identification markings" section for the
location of the tyre pressure label.
- Fit the long socket A
, the wheelbrace d
and bar
B to the securing screw.
-


t
urn the assembly clockwise to fully
draw in the cable and raise the wheel


under the vehicle.
-
Check that the wheel is positioned
horizontally flat against the floor of the


vehicle and that the the cut-out for the
carrier system is visible.
-
Stow the tools and the trim (depending
on version).
refitting the repaired wheel
Refitting the repaired wheel is the same as
fitting the spare wheel; don't forget to refit
the wheel trim.
the spare wheel is not designed to be used


over long distances. Have the tightening
of the bolts and pressure of the spare
wheel checked by a P
eugeOt dealer or a
qualified workshop without delay

.
Also, have the original wheel repaired and
refitted by a P
eugeOt dealer or a qualified
workshop as soon as possible.
Puncture

162
- If a pressure of at least 3 bar is not
reached within 5 minutes, disconnect
the compressor from the valve and the
power socket, then move the vehicle
forward by approximately 10 metres to
distribute the sealant fluid inside the
tyre.
-


t
hen repeat the inflation operation:
●
if a pressure of at least 3 bar

is not
reached within 10 minutes, switch off
your vehicle: the tyre has suffered
too much damage and repair has not
been possible. Contact a P
eugeOt
dealer or a qualified workshop.
●
if the tyre has been inflated to a
pressure of

5 bar, set off again
immediately.
After driving for approximately 10 minutes,
stop and check the pressure of the tyre
again.
Adjust the pressure to the value given on the
label on the driver's door pillar, and contact
a P
eugeOt dealer or a qualified workshop
as soon as possible.
checking and adjusting the
pressure
the compressor can only be used to check
and adjust the pressure.
-
Disconnect the hose I and connect it to


the tyre valve directly; the cartridge will
then be connected to the compressor
and the filling fluid will not be injected.
If it is necessary to deflate the tyre, connect
the hose I to the tyre valve and press the
yellow button, placed in the centre of the
switch on the compressor.
replacing the cartridge
to replace the sealant cartridge, carry out
the following operations:
-
disconnect the hose I ,
-
turn the cartridge to be replaced
anticlockwise and lift it,
-
insert the new cartridge and turn it
clockwise,
-
reconnect the hose I and connect the


hose B in its location.
the cartridge contains ethylene-glycol,


a product which is harmful if swallowed
and which causes irritation to the eyes.
Keep out of reach of children.
After use, do not discard the cartridge in the
environment, take it to a P
eugeOt


dealer

or an appropriate waste disposal
organisation.
this puncture repair kit and


replacement cartridges are available
from P
eugeOt dealers.
Puncture

165
Fitting the towball
Below the rear bumper, remove the
protective plug from the towball carrier.Insert the end of the towball 4
into the
carrier 1 and push upwards; it locks in place
automatically. Check that the mechanism has correctly
locked in to place (position A
).
Close the lock 6 using the key.
the locking wheel

5 turns a quarter of a turn
anti-clockwise; take care to keep your hands
clear. Always remove the.
the key cannot be


removed when the lock is open.
Clip the cap onto the lock.
transport solutions
QuICK HeLP
8

167
grasp the towball 4 firmly with one hand;
with the other hand, pull and turn the locking
wheel 5 clockwise as far as it will go; do not
release the locking wheel.
Maintenance
Correct operation is only possible if the
towball and its carrier remain clean.
Before cleaning the vehicle with a high
pressure jet wash, the towball must be
removed and the blanking plug inserted in
the carrier.
Apply the label provided to a clearly
visible area, close to the carrier or in
the boot.
For any work on the towbar, got to a
P
eugeOt dealer or a qualified workshop.
Refit the protective blanking plug to the
carrier

.
Carefully stow the towball in its bag away
from knocks and dirt.
extract the towball from the bottom of its


carrier 1.
Release the locking wheel; this automatically
stops in the unlocked position (position B ).
transport solutions
QuICK HeLP
8

187Menus
navigation
M
ediaradio
Settings
tele

phone Vehicle information
Settings for the navigation system and select a
destination.
Select from the different music sources.
Activate, deactivate, and adjust certain
functions.
Select from the different radio sources.
Activate, deactivate, and adjust certain
functions.
Activate, deactivate, and adjust certain
functions.
Connect a mobile telephone via Bluetooth
®.
Access to the ambient temperature, the clock,
the compass and the trip computer.
touch Screen Audio - telematic System
AuDIO and teLeMAtICS
10

2 11Level 1Level 2 Level 3com ment
M
orE
Am

bient temp. Displays the ambient temperature.
M
orE
cl

ock Displays the clock.
M
orE
com

pass Displays the direction of travel.
M
orE
tr i

p
curr
ent infoRange
Displays the trip computer.
Make a long press on the "
tri

p A" or "
tri
p B"
button to reset the trip in question.
Current fuel consumption
tr i

p AAverage fuel consumption
Average speed
Distance travelled
Journey time
tr i

p BAverage fuel consumption
Average speed
Distance travelled
Journey time
touch Screen Audio - telematic System
AuDIO and teLeMAtICS
10