2015 Peugeot Bipper ABS

28
Bipper_en_Chap03_pret-a-partir_ed02-2014
Warning lampisindicates Solution - action
Front airbag
l

ateral airbag flashing or
continuously on.
the failure of an airbag. Have the system checked by a P
euge O t
dealer or a

qualified workshop without delay.
"Safety - Airbags" section.
Deactivation of the
passenger's front
airbag on.
that this airbag has been
deactivated intentionally in the
presence of a rear facing child seat."technology on board - V
ehicle configuration"
section.
ABS continuously on. failure of the system.
t

he vehicle retains conventional braking without
assistance. However, we recommend that you stop and
contact a PEUGEOT dealer or a qualified workshop.
continuously on, coupled with
the parking brake warning lamp.a fault with the electronic
brake force distributor.Stop as soon as it is safe to do so. Park, switch off and
contact a PEUGEOT dealer or a qualified workshop.
trajectory control
system flashes for a few
seconds.
the DSC system has been
invoked. Intervention by the system to correct the
trajectory of the vehicle.
on, accompanied by a
message in the screen. a fault with the DSC
system. Contact a P euge O t
dealer or a qualified

workshop.
on, coupled with the
ASR OFF warning
lamp, accompanied by a
message in the screen. a fault with the ASR / MSR
system.
Contact a P
euge O t
dealer or a qualified

workshop.
on. a fault with the Intelligent
traction Control. Contact a P

euge O t
dealer or a qualified

workshop.
Hill start assist on.a fault with the hill start
assist system. Contact a P
euge O t
dealer or a qualified

workshop.
Instruments and controls

40
Bipper_en_Chap03_pret-a-partir_ed02-2014
ALARM
this provides:
-
exterior perimeter protection by means of

detectors on the doors and bonnet and
on the electrical supply,
-

interior protection,
-


anti-tilt protection,
-


protection against the unauthorised

insertion of a key in the starter.
t

he equipment includes a siren.
Activation of the alarm
First ensure that all of the accesses are
closed correctly.
t
he alarm is activated by pressing
this control, the protection is
active after a few seconds.
While the alarm is monitoring, any
intrusion triggers the siren for approximately
30 seconds, accompanied by illumination of
the direction indicators.
t

he alarm then returns to monitoring mode.
t

he alarm is also triggered following an
electrical supply cut-off, when the supply is
restored.
Deactivation using the remote control
Deactivation using the key
unlock the doors using the key and enter
the vehicle. Switch on the ignition to the
RUNNING position, identification of the key
code will switch off the alarm.
Deactivation of the volumetric and
anti-tilt protection Good practice
to quickly deactivate the siren following

unwanted triggering, unlock the vehicle
using the remote control.
to avoid setting the alarm, before washing


the vehicle for example, lock the vehicle
using the key.
When this button is pressed, the
alarm is deactivated when the
vehicle is unlocked.
Signalling of attempted intrusion
When you return to your vehicle,
flashing of the electronic engine
immobiliser warning lamp or
the appearance of a warning
message in the instrument panel display
indicates an attempted intrusion during your
absence.
to deactivate the volumetric


and anti-tilt protection, press the
button located in the vehicle's
courtesy lamp.
to be ef

fective,
this operation must be repeated every time
the ignition is switched off.
Access

49
Bipper_en_Chap03_pret-a-partir_ed02-2014
Reactivation
- Press the button on the
end of the control again.
or
-

Press the accelerator pedal until a speed

close to the programmed speed.
-
e
ngage the gear selected when
programming the speed.
Your vehicle will return to the last
programmed speed.
When the system is activated,
t

he "Cruise
control" warning lamp comes on in the
instrument panel.
CRUISE CONTROL
"this is the speed at which the driver wishes
to drive".
t

his aid to driving in free-flowing traffic
enables the vehicle to maintain the speed
programmed by the driver, without use of the
accelerator pedal.
In order for it to be programmed or
activated, the vehicle speed must be greater
than 18 mph (30 km/h) with at least second
gear engaged on the manual gearbox.
Selecting the function
- Place the ring in the
ON position.
t
he cruise
control is selected but
is not yet active and
no speed has been
programmed.
First activation /
Programming
a speed
- Reach the chosen
speed by pressing the
accelerator.
-

Move the control up (+) for at least one

second then release it.
t

his programmes the reference speed. You
can release the accelerator pedal, and the
vehicle will maintain this speed.
Temporarily exceeding
of the speed
It is possible to accelerate
and drive momentarily at
a speed greater than the
programmed speed (for example to overtake
another vehicle).
When the accelerator pedal is released, the
vehicle will return to the programmed speed.
Deactivation
- Press the button on
the end of the control.
or
-

Press the brake or clutch pedal.
t

he cruise control is also deactivated if the
ABS or DSC system is invoked.
3
READY TO SET OFF
Steering mounted controls

76
Bipper_en_Chap04_ergonomie_ed02-2014
Smoker's kit
located at the base of the centre console,
this consists of a cigarette lighter and an
ashtray.
12 V socket (180 W max)
An accessory socket is provided next to the
cigarette lighter.
FRONT FITTINGS
Folding writing table
(Light van)
this is located in the centre of the
dashboard. In the absence of a table, the
vehicle is fitted with a storage compartment.
t

he clip can be used to secure A5 format
documents, slips, etc.
Pull the top of the table to unfold it, push to
fold it.
Door pockets
With recess for storing a 1 litre bottle.
Practical information

11 2
Bipper_en_Chap06_securite_ed02-2014
HORN
Press the centre of the steering wheel.
Anti-lock braking system and
electronic brake force distribution
linked systems which improve the stability
and manoeuvrability of your vehicle when
braking, in particular on poor or slippery
surfaces.
BRAKING ASSISTANCE SYSTEMS
group of supplementary systems which help
you to obtain optimum braking in complete
safety in emergency situations:
-

anti-lock braking system (ABS),
-


electronic brake force distribution

(
e BFD),
-

emergency braking assistance (
e BA).Activation
t

he anti-lock braking system comes into
operation automatically when there is a risk
of wheel lock.
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal accompanied by some noise.
When braking in an emergency
, press
very firmly without releasing the
pressure.
Operating fault If this warning lamp comes on,
accompanied by an audible signal
and a message in the instrument
panel screen, it indicates a fault
with the anti-lock braking system which
could result in loss of control of the vehicle
when braking. If this warning lamp comes on,
together with the ABS warning
lamp, accompanied by a message
in the instrument panel screen,
it indicates a fault with the electronic brake
force distribution which could result in loss
of control of the vehicle when braking.
You must stop as soon as it is safe to do so.
Good practice
t
he ABS system does not provide shorter
braking distances. On very slippery surfaces
(black ice, oil...) the ABS can extend braking
distances. For emergency braking, press the
brake pedal hard and do not release it, even
on a slipper surface; you will then be able to
steer the vehicle and avoid an obstacle.
When replacing wheels (tyres and
rims), ensure that they conform to the
manufacturer's recommendations. In either case, contact a P euge O t
dealer

or a qualified workshop.
For maximum braking efficiency, a
bedding-in period of around 300 miles
(500 kilometres) is needed. During this
period it is recommended that you avoid
harsh, repeated or prolonged braking.
Driving safely

138
Bipper_en_Chap07_accessoire_ed02-2014
In certain cases of particularly arduous
use (towing the maximum load up a steep
slope in high temperatures), the engine
automatically limits its power. In this case,
automatic cutting off of the air conditioning
allows the engine power to be saved.If the coolant temperature
warning lamp comes on, stop the
vehicle and switch off the engine
as soon as possible.
ChecksSee the "
l evels" section of
chapter 7.
Tyres: check the tyre pressures on the
towing vehicle and the trailer, observing the
recommended pressures.
Brakes: towing increases the braking
distance. Drive at a moderate speed,
change down early and brake gradually. Side wind: sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed.
ABS: the system only controls the vehicle,
not the trailer.
Distribution of loads
Distribute the load in the trailer so that the
heaviest objects are as close as possible
to the axle and the nose weight is close to
the maximum authorised without, however,
exceeding it.
t

he air density decreases with
altitude, so reducing the performance of the
engine.
t

he maximum towed load must be
reduced by 10 % for each 1 000 metres of
altitude.
Refer to the "
t
echnical data -


Identification markings" section. Rear parking sensors: the sensors will be
deactivated automatically when an genuine
P
euge O t towbar is used.
Towbar
We recommend the use of genuine
P
euge O t towbars and their harnesses,
which have been tested and approved from
the design stage of your vehicle, and that
the fitting of this equipment is entrusted to a
P
euge O t
dealer or a qualified workshop.
If this equipment is not fitted by a P

euge O t

dealer

, it is essential that it is fitted using
the electrical pre-equipment located at
the rear of the vehicle and following the
manufacturer's instructions.
t

he operation of the rear parking sensors is
deactivated automatically when the trailer
cable connector is inserted in the towbar
socket.
When the trailer cable is removed, the rear
parking sensors are re-activated.
Refer to the "
t
echnology on board -


Parking sensors" section.
For information on the maximum
weights and towed loads applicable to
your vehicle, refer to the "
t
echnical data -


Weights" section.
Towing a trailer

164
Bipper_en_Chap09_aide-rapide_ed02-2014
Rear lamps
- Identify the faulty bulb then open the rear
doors.
-
u nscrew the two screws using the
screwdriver supplied in the tool kit
(behind the driver's seat) and extract the
bulb holder.
-

Release the lamp unit.
-


Disconnect the electrical connector
.
-

Remove the support by moving aside the

tabs.
-

Change the bulb.
Number plate lamps
Type A, C 5 W - 5 W
- u nclip the transparent cover using
the screwdriver supplied in the tool kit
(behind the driver's seat) and extract the
bulb holder.
-

Change the bulb by moving aside the two

contacts.
-
e nsure that the new bulbs are secured
correctly between the two contacts.
-

Replace the plastic lens and press on it.
For further information concerning the bulbs,


refer to the table "
t
ypes of bulb".
1.


Brake lamps


T

ype B, P21 W - 21 W
2.

Direction indicators


T

ype B, PY 21 W - 21 W amber
3.

Reversing lamps


T

ype B, P21 W - 21 W
4.

Sidelamps/Foglamps


T

ype B, P4/21

W - 4

W/21

W On the hinged rear doors On the tailgate
Changing a bulb

165
Bipper_en_Chap09_aide-rapide_ed02-2014
Third brake lamp
On the hinged rear doors
Type B, W 5 W - 5 W (4 bulbs)
- u nclip the transparent cover using the
screwdriver located in the tool kit.
-

Disconnect the electrical connector
.
-

Remove the bulb holder by squeezing the

two tabs.
-

Remove the faulty bulb.
-


Change the bulb. On the tailgate
T

ype B, W5W - 5W (5 bulbs)
-

Open the tailgate.
-


Remove the two cover retaining screws,

then the cover.
-

Remove the bulb holder by squeezing the

two tabs.
-

Remove the faulty bulb.
-


Change the bulb.
If you encounter any dif

ficulty, consult a
P
euge O t
dealer or a qualified workshop.
9
QUICK HELP
Changing a bulb