2015 Peugeot 208 remote control

Access
44
208_en_Chap02_ouvertures_ed01-2016
Changing the battery
Battery ref.: CR1620 / 3 volts. If the battery is flat, you are informed
by lighting of this warning lamp in the
instrument panel, an audible signal
and a message in the screen.
F

U
nclip the cover using a screwdriver in the
cutout.
F

R
emove the cover.
F

E
xtract the flat battery from its location.
F

P
lace the new battery into its location
observing the original direction.
F

C
lip the cover in place.
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
Remote control problem
Reinitialisation
F Switch off the ignition.
F
T urn the key to position 2 (Ignition) .
F

P
ress the closed padlock immediately for a
few seconds.
F

S
witch off the ignition and remove the key
from the ignition switch.
The remote control is fully operational again.
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F

F

irst of all, use the key in the lock to unlock
or lock your vehicle.
F

T

hen, reinitialise the remote control.
If the problem persists, contact a PEUGEOT
dealer as soon as possible.

Access45
208_en_Chap02_ouvertures_ed01-2016
Lost keys
Go to a PEUGEOT dealer with the vehicle's
registration document, your personal
identification documents and if possible the
key code label.
The PEUGEOT dealer will be able to look
up the key code and the transponder code
required to order a new key.
Remote control
The high frequency remote control is a
sensitive system; do not operate it while it is
in your pocket as there is a possibility that
it may unlock the vehicle, without you being
aware of it.
Do not repeatedly press the buttons of your
remote control out of range and out of sight
of your vehicle. You run the risk of stopping
it from working and the remote control
would have to be reinitialised.
No remote control can operate when the
key is in the ignition switch, even when
the ignition is switched off, except for
reinitialisation.
Anti-theft protection
Do not make any modifications to the
electronic engine immobiliser system; this
could cause malfunctions.
Locked vehicle
Driving with the doors locked may make
access to the passenger compartment by
the emergency services more difficult in an
emergency.
As a safety precaution, never leave children
alone in the vehicle, except for a very short
period.
In all cases, it is essential to remove the key
from the ignition switch when leaving the
vehicle.
Second-hand vehicle
Have the pairing of all of the keys in your
possession checked by a PEUGEOT dealer,
to ensure that only your keys can be used to
open and start the vehicle.
2

Ease of use and comfort
68
208_en_Chap03_ergonomie-confort_ed01-2016
Courtesy lamp
In this position, the lighting
comes on gradually:
-

w

hen the vehicle is unlocked,
-

w

hen the key is removed from the ignition,
-
w

hen opening a door,
-

w

hen unlocking with the remote control.
It goes off gradually:
-

w

hen the vehicle is locked,
-

w

hen the ignition is switched on,
-

3

0 seconds after the last door is closed. Permanently off.
Permanent lighting. F
W ith the ignition on, press
the corresponding switch.
1.
C

ourtesy lamp
2.
M

ap reading lamp s
With the "permanent lighting" mode, the lighting
time varies according to the circumstances:
- with the ignition off, approximately
10
minutes,
- in energy economy mode, approximately
30 seconds,
- with the engine running, unlimited.
Map reading lamps
Take care to avoid leaving anything in
contact with the courtesy lamp.

76
Using the remote control
Adjustment
F U nlock the vehicle with the remote control
to unfold the door mirrors.
F

W
hen locking the vehicle, the mirrors fold
automatically.
Automatic rear view mirror
A sensor measuring the light from the rear of
the vehicle, automatically and progressively
adjusts the brightness of the mirror.
Manual rear view mirror
If the mirrors are folded using control A ,
t hey will not unfold when the vehicle
is unlocked. It is necessary to press
control A again.
The automatic folding and unfolding
of the rear view mirrors when using
the remote control can be deactivated
by a PEUGEOT dealer or a qualified
workshop.
Fold the mirrors when using an
automatic car wash.
If necessary, it is possible to fold the
mirrors manually. The objects observed are, in reality,
closer than they appear.
Take this into account in order to
correctly judge the distance of vehicles
approaching from behind. The rear view mirror has two positions:
-

d
ay (normal),
-

n
ight (anti-dazzle).
To change from one to the other, push or pull
the lever on the lower edge of the mirror.
Lighting and visibility

80
Temporarily keeping the dipped beam
headlamps on after the vehicle's ignition has
been switched off makes the driver's exit easier
when the light is poor.
Manual guide-me-home
lighting
On
F With the ignition off, "flash" the headlamps using the lighting stalk.
F

A f
urther "headlamp flash" switches the
function off.
Off
The manual guide-me-home lighting switches
off automatically after a set time.
Parking lamps
Side markers for the vehicle by illumination of
the sidelamps on the traffic side only.
F

W
ithin one minute of switching off the
ignition, operate the lighting control stalk
up or down depending on the traffic side
(for example: when parking on the left;
lighting control stalk upwards; the right
hand sidelamps are on).
Manual guide-me-home lighting
is also available from the remote
control lighting button (refer to the
corresponding section). This is confirmed by an audible signal and
illumination of the corresponding direction
indicator warning lamp in the instrument panel.
To switch off the parking lamps, return the
lighting control stalk to the middle position or
switch on the ignition.
Lighting and visibility

Driving
118
208_en_Chap06_conduite_ed01-2016
Starting
Gearbox Ignition
Avoid attaching heavy objects to the
key or the remote control, which would
weigh down on its blade in the ignition
switch and could cause a malfunction.
It could adversely affect the deployment
of the front airbag.
The original key contains a coded electronic chip.
When the ignition is switched on, starting is only
possible if the code is detected and recognised.
This protection against theft locks the engine
management system a few moments after the
ignition is switched off and prevents starting of
the engine following a break-in.
Electronic engine immobiliser
Keep away from your vehicle, the
label attached to the keys given to you
on acquisition of the vehicle. It will
help in finding the original code for
replacement of the key.
In the event of a fault, you are informed
by illumination of the warning lamp, an
Manual
F Place the gear lever in neutral.Advice
Automatic
F Place the gear lever at position P or N .
Electronic
F Place the gear lever at position N.
Steering wheel
In some cases, you may have to apply
some force to turn the steering (if the
wheels are on lock against a kerb, for
example).
Starting
F Insert the key into the ignition switch. T
he system recognises the starting code.
F

U
nlock the steering column by
simultaneously turning the steering wheel
and the key.
F

T
urn the key towards the dashboard to
position 3 (Starting) .
F

W
hen the engine starts, release the key. audible signal and the display of a message.
In this case, your vehicle will not start; contact a
PEUGEOT dealer as soon as possible.

In the event of a breakdown
208
208_en_Chap08_cas-de-panne_ed01-2016
12 V battery
Versions equipped with Stop & Start are
fitted with a 12 V lead-acid battery of
specific technology and specification.
Its replacement should be carried
out only by a PEUGEOT dealer or a
qualified workshop.
Procedure for starting the engine using another battery or charging a discharged battery.
The battery is located under the bonnet.
To gain access to it:
F o pen the bonnet using the interior release
lever, then the exterior safety catch,
F

s
ecure the bonnet stay,
F

r
emove the plastic cover on the (+)
terminal.
Access to the battery
If your vehicle has an automatic
gearbox, do not try to start the engine
by pushing the vehicle.
Batteries contain harmful substances
such as sulphuric acid and lead.
They must be disposed of in
accordance with regulations and must
not, in any circumstances, be discarded
with household waste.
Take used remote control batteries and
vehicle batteries to a special collection
point.
General points
Lead-acid starter batteries
Protect your eyes and face before
handling the battery.
All operations on the battery must be
carried out in a well ventilated area and
away from naked flames and sources
of sparks, so as to avoid the risk of
explosion or fire.
Wash your hands afterwards.
If your vehicle has an electronic
gearbox, do not try to start the engine
by pushing the vehicle.
The (-) terminal of the battery is not accessible.
A remote earth point is located on the engine.

In the event of a breakdown211
208_en_Chap08_cas-de-panne_ed01-2016
Disconnecting the battery
It is recommended that the battery be
disconnected if the vehicle is not to be used
for a very long period, so as to maintain an
adequate state of charge for starting the
engine.
Before disconnecting the battery:
F
c
lose all openings (doors, boot, windows,
roof),
F

s
witch off all electrical consumers (audio
system, wipers, lighting...),
F

s
witch off the ignition and then wait
four


minutes.
At the battery, simply detach the (+) terminal.
The Stop & Start system may not be
operational during the trip following the
first engine start.
In this case, the system will only be
available again after a continuous
period of immobilisation of the vehicle,
a period which depends on the ambient
temperature and the state of charge of
the battery (up to about 8 hours).
Following reconnection of the
battery
Following reconnection of the battery, switch on
the ignition and wait 1 minute before starting to
permit initialisation of the electronic systems.
However, if problems remain following this
operation, contact a PEUGEOT dealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise (depending on
version):
-

t
he remote control key,
-


...
Quick-release terminal
Disconnecting the (+) cable
F Raise the lever D fully to release the cable terminal clamp E .
Reconnecting the (+) cable
F Position the open clamp E of the cable on
the positive post (+) of the battery.
F

P
ress vertically on the clamp E to position
it correctly on the battery.
F

L
ock the clamp by spreading the
positioning lug and then lowering
the lever D .
Do not apply excessive force on the
tab as locking will not be possible if the
clamp is not positioned correctly; start
the procedure again.
8