2015 NISSAN QUEST mirror


> (GLW    0RGHO (' @
.Use the displayed lines and the bird's-eye
view as a reference. The lines and the bird's-
eye view are greatly affected by the number
of occupants, fuel level, vehicle position,
road condition and road grade.
SAA3571
Front-side viewGUID-04849896-C828-42DE-B9D2-225B3EFD328EGuiding lines:
Guiding lines that indicate the width and the
front end of the vehicle are displayed on the
monitor.
The front-of-vehicle line
*1shows the front part
of the vehicle.
The side-of-vehicle line
*2shows the vehicle
width including the outside mirrors.
The extensions
*3of both the front*1and
side
*2lines are shown with a green dotted
line.
CAUTION
. The turn signal light may look like
the side-of-vehicle line. This is not a
malfunction.
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-35
&RQGLWLRQ


> (GLW    0RGHO (' @
4-38Monitor, heater, air conditioner, audio, phone and voice recognition systems
course.
HOW TO SWITCH THE DISPLAYGUID-666130BA-C2F3-463E-A7FE-5BBA4EC5786DWith the ignition switch in the ON position,
press the CAMERA button or move the shift
lever to the R (Reverse) position to operate the
Around View Monitor.
When the rear view is displayed on the left side
on the screen, the view on the right side
switches between the bird's-eye view and the
front-side view each time the CAMERA button is
pushed.
When the front view/bird's eye view is displayed
on the screen, pushing the CAMERA button will
switch the view on the right side to the front-side
view. When the CAMERA button is pushed
again, the screen which was displayed before
the Around View Monitor was activated is
displayed.
If the shift lever is in the R (Reverse) position, the
available views are:
.Rear view/bird's-eye view split screen
. Rear view/front-side view split screen
If the shift lever is in the P (Park) position, the
available views are:
. Front-view/bird's-eye view split screen
. Front-view/front-side view split screen
If the shift lever is in the D (Drive) position, the
only available view is front view/front-side view split screen.
The display will switch from the Around View
Monitor screen when:
.
When the shift lever is in the D (Drive)
position and the vehicle speed increases
above approximately 6 MPH (10 km/h) .
. When a different screen is selected.
HOW TO ADJUST THE SCREENGUID-D7D0605F-B226-4C3F-ACCC-199024F184E8To adjust the Display ON/OFF, Brightness, Tint,
Color, Contrast and Black Level of the Around
View Monitor, push the SETTING button with
the Around View Monitor on, select the item key
and adjust the level using the multi-function
controller.
Do not adjust the Brightness, Tint, Color,
Contrast and Black Level of the Around View
Monitor while the vehicle is moving. Make sure
the parking brake is firmly applied.
MOVING OBJECT DETECTION (MOD)
FUNCTION
GUID-07B1BAB2-9273-4950-8DE2-2CDABED123ECThe Moving Object Detection (MOD) system
can inform the driver of moving objects when
driving out of garages, maneuvering into parking
lots and in other such instances.
The MOD system detects moving objects by
using image processing technology on the
image shown in the display.
The MOD system operates in the following
conditions when the camera view is displayed:
.When the shift lever is in the ªPº or ªNº
position and the vehicle is stopped, the
MOD system detects the moving objects in
the bird's-eye view. The MOD system will
not operate if the outside mirror is moving in
or out or if either door is opened.
. When the shift lever is in the ªDº position
and the vehicle speed is below approxi-
mately 5 MPH (8 km/h) , the MOD system
detects moving objects in the front view.
. When the shift lever is in the ªRº position
and the vehicle speed is below approxi-
mately 5 MPH (8 km/h) , the MOD system
detects moving objects in the rear view. The
MOD system will not operate if the lift gate is
open.
The MOD system does not detect moving
objects in the front-side view. The MOD icon
&RQGLWLRQ


> (GLW    0RGHO (' @
is not displayed on the screen when in this view.
WARNING
.The MOD system is not a substitute
for proper vehicle operation and
does not prevent contact with the
objects surrounding the vehicle.
When maneuvering, always use the
outside mirror and inside rearview
mirror and turn and look to check
the surroundings to make sure it is
safe to maneuver.
. The system is not designed to pre-
vent contact with all objects.
. The MOD system is not designed to
detect surrounding stationary ob-
jects.
JVH0872X
bird's-eye view
JVH0873X
front view / rear view
When the MOD system detects a moving object
surrounding the vehicle, the yellow frame will be
displayed on the view where the objects are
detected and a chime will sound once. While the
MOD system continues to detect moving
objects, the yellow frame continues to be
displayed.
In the bird's-eye view, the yellow frame
*1is
displayed on each camera image (front, rear,
right, left) depending on where moving objects
are detected.
The yellow frame
*2is displayed on each view
in the front view and rear view modes.
A blue MOD icon is displayed in the view where
the MOD system is operative. A gray MOD icon
is displayed in the view where the MOD system
is not operative.
If the MOD system is turned off, the MOD icon
*3is not displayed.
The MOD system will turn on automatically
under the following conditions:
. When the shift lever is in the ªRº (Reverse)
position.
. When the CAMERA button is pushed to
switch from a different screen to the camera
view on the display.
. When vehicle speed decreases below
approximately 5 MPH (8 km/h) .
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-39
&RQGLWLRQ


> (GLW    0RGHO (' @
4-44Monitor, heater, air conditioner, audio, phone and voice recognition systems
SAA3596
1. Temperature control buttons
2. ª
º air recirculation button
3. ª
º outside air circulation button
4. ª
FRONTº front defroster button
5. Display
6. ª
REARº rear window defroster button (See
ªRear window and outside mirror defroster
switchº (P.2-32) .) 7. ª
º and ªº fan speed control
buttons
8. ªON´OFFº button for air conditioning system
9. ªMODEº air flow control button
10. ªA/Cº air conditioner ON/OFF button
11. ªREARº control button
MANUAL AIR CONDITIONERGUID-CD7203EA-9307-4995-82E3-BD3B0296D19F
ControlsGUID-A04F8617-DF9F-4F48-BC23-EDEDEDFFC3B1To turn off the heater and air conditioner, push
the ªON´OFFº button.
Fan speed control:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Push the fan speed control button ªº to
increase the fan speed.
Push the fan speed control button ª
º to
decrease the fan speed.
A/C (Air Conditioner) operation:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Push the A/C button to turn on or off the air
conditioner. When the air conditioner is on, the
A/C indicator light on the button illuminates.
Air flow control:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Push the ªMODEº button to change the air flow
mode.
: Air flows from the center and side ventila- tors.
: Air flows from the center and side ventila-tors, and foot outlets.
: Air flows mainly from the foot outlets.
: Air flows from the defroster and foot outlets.
Temperature control:GUID-D73A39BF-43C8-459F-9C24-47B7F579C407Push the temperature control buttons (ªº
and ª
º) to set the desired temperature.
&RQGLWLRQ


> (GLW    0RGHO (' @
SAA3595
1. Temperature control buttons (driver side)
2. ª
º air recirculation button
3. ª
AUTOº auto-recirculation button (models
with Advanced Climate Control System)/ªº
Outside air circulation button (models without
Advanced Climate Control System)
4. ª
FRONTº front defroster button 5. Display
6. ª
REARº rear window defroster button (See
ªRear window and outside mirror defroster
switchº (P.2-32) .)
7. Temperature control buttons (passenger side)
8. ªMODEº manual air flow control button
9. ªON´OFFº button for air conditioning system 10. ªAUTOº button
11. ª
º fan speed control buttons
12. ªA/Cº air conditioner ON/OFF button
13. ªREARº control button
14. ªDUALº zone control ON/OFF button
AUTOMATIC AIR CONDITIONERGUID-26808BE2-2D7D-4D4F-81C9-3D2D1185C3FD
Automatic operation (AUTO)GUID-D3349AE0-1D21-4681-9BC9-F5E415C17B3AThe AUTO mode may be used year-round as the
system automatically controls constant tempera-
ture, air flow distribution and fan speed after the
desired temperature is set manually.
To turn the heater and air conditioner on or off,
push the ªON´OFFº button.
Cooling and dehumidified heating:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C4071. Push the ªAUTOº button.
(The AUTO indicator light will illuminate.)
2. If the A/C indicator light does not illuminate, push the ªA/Cº button.
(The A/C indicator light will illuminate.)
3. Push the temperature control buttons
(ª
º and ªº) (driver's side) to set the
desired temperature.
.When ªDUALº does not appear on the display:
Pushing the ªAUTOº button changes
both the driver's and front passenger's
side temperature.
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-49
&RQGLWLRQ


> (GLW    0RGHO (' @
SSD0944
INTELLIGENT KEY BATTERY DIS-
CHARGE
GUID-32EAE25A-244A-4FE6-B7B9-0A44E3665695If the battery of the Intelligent Key is discharged,
or environmental conditions interfere with the
Intelligent Key operation, start the engine
according to the following procedure:
1. Move the shift lever to the P (Park) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the IntelligentKey as illustrated. (A chime will sound.)
4. Push the ignition switch while depressing the brake pedal within 10 seconds after the
chime sounds. The engine will start.
After step 3 is performed, when the ignition switch is pushed without depressing the brake
pedal, the ignition switch position will change to
ACC.
NOTE:
.
When the ignition switch is pushed to
the ACC or ON position or the engine is
started by the above procedures, the
Intelligent Key battery discharge indi-
cator appears on the vehicle informa-
tion display even if the Intelligent Key
is inside the vehicle. This is not a
malfunction. To turn off the Intelligent
Key battery discharge indicator, touch
the ignition switch with the Intelligent
Key again.
. If the Intelligent Key battery discharge
indicator appears, replace the battery
as soon as possible. (See ªIntelligent
Key battery replacementº (P.8-23) .)
GUID-D80103F1-BD55-4C4A-B18B-FCA59EEB6917.Make sure the area around the vehicle is
clear.
. Check fluid levels such as engine oil, cool-
ant, brake fluid and window washer fluid as
frequently as possible, or at least whenever
you refuel.
. Check that all windows and lights are clean.
. Visually inspect tires for their appearance
and condition. Also check tires for proper
inflation.
. Lock all doors.
. Position seats and adjust head restraints/
headrests.
. Adjust inside and outside mirrors.
. Fasten seat belts and ask all passengers to
do likewise.
. Check the operation of warning lights when
the ignition switch is pushed to the ON
position. (See ªWarning/indicator lights and
audible remindersº (P.2-11) .)
Starting and driving5-11
BEFORE STARTING THE ENGINE
&RQGLWLRQ


> (GLW    0RGHO (' @
SPA2331
To apply:Fully depress the parking brake pedal
*1.
To release:
1. Firmly apply the foot brake
*2.
2. Depress the parking brake pedal
*1and
the parking brake will be released.
3. Before driving, be sure the brake warning light goes out.
GUID-8C590A26-003A-4629-B1A7-BD81A3C3475E
WARNING
.The BSW system is not a replace-
ment for proper driving procedure
and is not designed to prevent
contact with vehicles or objects.
When changing lanes, always use
the side and rear mirrors and turn
and look in the direction you will
move to ensure it is safe to change
lanes. Never rely solely on the BSW
system.
. The BSW system operates above
approximately 20 MPH (32 km/h) .
The Blind Spot Warning (BSW) system can
help alert the driver of other vehicles in adjacent
lanes when changing lanes.
SSD1178
The BSW system uses radar sensors*A
installed near the rear bumper to detect other
vehicles in an adjacent lane.
Starting and driving5-17
BLIND SPOT WARNING (BSW)
SYSTEM (if so equipped)
&RQGLWLRQ


> (GLW    0RGHO (' @
5-18Starting and driving
SSD1030
Detection zone
The radar sensors can detect vehicles on either
side of your vehicle within the detection zone
shown as illustrated. This detection zone starts
from the outside mirror of your vehicle and
extends approximately 10 ft (3 m) behind the
rear bumper, and approximately 10 ft (3 m)
sideways.
The BSW system operates above approximately
20 MPH (32 km/h) . If the radar sensors detect a
vehicle in the detection zone, the BSW indicator
light illuminates. If the driver then activates the
turn signal, a chime will sound twice and the
BSW indicator light will flash.
SSD1184
BSW indicator light
SSD1029
BSW system warning light
SSD1179
BSW switch
BSW SYSTEM OPERATIONGUID-B7B4A2DD-5B73-4122-8C65-5DB3CA4A4566If the radar sensors detect a vehicle in the
detection zone, the BSW indicator light in the
outside mirror will illuminate in the direction of
the detected vehicle. If the turn signal is then
activated, the system chimes (twice) and the
BSW indicator light flashes. The BSW indicator
light continues to flash until the detected vehicle
leaves the detection zone.
The BSW indicator lights illuminate for a few
seconds when the ignition switch is placed in
the ON position.
The brightness of the BSW indicator lights is
adjusted automatically depending on the bright-
&RQGLWLRQ