2015 NISSAN JUKE engine


> (GLW   0RGHO )'@
opening. Donot overfill
*
B
.
6. Recheck oillevel withthedipstick.
It is normal toadd some oilbetween oil
maintenance intervalsorduring thebreak -
in period, depending onthe severity of
operating conditions.
CAUTION
Oil level should bechecked regularly.
Operating theengine withaninsuffi-
cient amount ofoil can damage the
engine, andsuch damage isnot cov-
ered bythe warranty.
CHANGING ENGINEOILAND FILTER
GUID-14 29280C-216 4-4979-AB59-A82BB A48D3F2
Change theengine oiland filter according tothe
maintenance logshown inthe NISSAN Service
and Maintenance Guide.
V ehicle set-up
GUID-D33 812FA-0489-4509 -B0E6-6388A81BEBEA
1. Park thevehicle onalevel surface andapply
the parking brake.
2. Run theengine untilitreaches theoperating
temperature.
3. Turn theengine offand wait more than10
minutes. 4.
Raise andsupport thevehicle usinga
suitable floorjackandsafety jackstands.
.
Place thesafety jackstands underthe
vehicle jack-up points.
.
A suitable adaptershouldbeattached to
the jack stand saddle.
CAUTION
Make surethecorrect liftingandsup-
port points areused toavoid vehicle
damage.
SDI2652
For NISMO RS models
JVM0518X
Except forNISMO RSmodels
Maintena nceand do-it-yo urself
8-9
&RQGLWLRQ


> (GLW   0RGHO )'@
8-10
Maintenance anddo-it-yours elf
SDI2651
1. Oilfiller cap
2. Oildrain plug
3. Oilfilter
Engine oiland filter
GUID-0E3 F5EC9-066 C-4F79-BD C5-1BCF07 F45F7E
1. Place alarge drain panunder thedrain plug.
2. Remove theoilfiller cap.
3. Remove thedrain plugwithawrench and
completely draintheoil.
CAUTION
Be careful nottoburn yourself, asthe
engine oilishot.
.
Waste oilmust bedisposed of
properly.
.
Check yourlocal regulations.
(Perform steps4to 7only when theengine
oil filter change isneeded.)
4. Loosen theoilfilter withanoilfilter wrench.
Remove theoilfilter byturning itby hand.
5. Wipe theengine oilfilter mounting surface
with aclean rag.
CAUTION
Be sure toremove anyoldgasket
material remaining onthe mounting
surface ofthe engine. Failuretodo so
could leadtoengine damage.
6. Coat thegasket onthe new filter withclean
engine oil.
7. Screw inthe oilfilter clockwise untilaslight
resistance isfelt, then tighten additionally
more than2/3turn.
Oil filter tightening torque:
11 to15 ft-lb
(14.7 to20.5 N´m)
8. Clean andre-install thedrain plugwitha
new washer. Securely tightenthedrain plug
with awrench. Drain
plugtightening torque:
22 to29 ft-lb
(29 to39 N´m)
Do not use excessive force.
9. Refill theengine withtherecommended oil
through theoilfiller opening, andinstall the
oil filler capsecurely .
See ªCapacities andrecommended fluids/
lubricantsº (P.9-2) fordrain andrefill capa-
city .The drain andrefill capacity depends on
the oiltemperature anddrain time.Use
these specifications forreference only.Al-
ways usethedipstick todetermine the
proper amount ofoil inthe engine.
10. Start theengine andcheck forleakage
around thedrain plugandtheoilfilter.
Correct asrequired.
11. Turn theengine offand wait more than10
minutes. Checktheoillevel withthedipstick.
Add engine oilifnecessary .
After theoperation
GUID-02 E3EFF4-6A0C -4167-AC8B-E5E800B0 3EDA
1. Lower thevehicle carefully tothe ground.
2. Dispose ofwaste oiland filter properly .
&RQGLWLRQ


> (GLW   0RGHO )'@
WARNING
. Prolonged andrepeated contact
with used engine oilmay cause skin
cancer.
. Try to avoid direct skincontact with
used oil.Ifskin contact ismade,
wash thoroughly withsoap orhand
cleaner assoon aspossible.
. Keep usedengine oilout ofreach of
children.
GUID-493B4 2A6-9A7A-45 D2-8DCD-565E3D1E9BF5
When checking orreplacement isrequired, we
recommend aNISSAN dealerforservicing.
FOR NISMO RSMODELS
GUID-03 F5E020-B55 2-496A-8BE2 -9A8E0DC58D8D
CAUTION
. NISSAN recommends usingGenu-
ine NISSAN CVTFluid NS-2ONLYin
NISSAN CVTs.Do not mix with other
fluids.
. Do not use Automatic transmission
fluid (ATF) orManual transmission
fluid inaNISSAN CVT,as itmay
damage theCVT .Damage causedby
the use offluids otherthanas
recommended isnot covered under
NISSAN's NewVehicle Limited War-
ranty.
. Using fluidsthatarenot equivalent
to Genuine NISSANCVTFluid NS-2
may also damage theCVT.Damage
caused bythe use offluids other
than asrecommended isnot cov-
ered under NISSAN's NewVehicle
Limited Warranty.
EX CEPT FORNISMO RSMODELS
GUID-B9 76A947-EA DA-4433-892 2-1E0C523646B1
CAUTION
. NISSAN recommends usingGenu-
ine NISSAN CVTFluid NS-3ONLYin
NISSAN CVTs.Do not mix with other
fluids.
. Do not use Automatic transmission
fluid (ATF) orManual transmission
fluid inaNISSAN CVT,as itmay
damage theCVT .Damage causedby
the use offluids otherthanas
recommended isnot covered under
NISSAN's NewVehicle Limited War-
ranty.
. Using fluidsthatarenot equivalent
to Genuine NISSANCVTFluid NS-3
may also damage theCVT.Damage
caused bythe use offluids other
than asrecommended isnot cov-
ered under NISSAN's NewVehicle
Limited Warranty.
Maintenance anddo-it-yo urself
8-11
CONTINUOUSL YVARIABLE
TRANSMISSIO N(CVT) FLUID
&RQGLWLRQ


> (GLW   0RGHO )'@
Refill thereservoir morefrequently whendriving
conditions requireanincreased amountof
window washerfluid.
Recommended fluid:
Genuine NISSAN Windshield Washer Concen-
trate Cleaner &Antifreeze orequivalent
CAUTION
. Donot substitute engineanti-freeze
coolant forwindow washersolution.
This mayresult indamage tothe
paint.
. Do not fillthe window washer
reservoir tankwithwasher fluid
concentrates atfull strength. Some
methyl alcohol basedwasher fluid
concentrates maypermanently stain
the grille ifspilled whilefilling the
window washerreservoir tank.
. Pre-mix washerfluidconcentrates
with water tothe manufacturer's
recommended levelsbefore pouring
the fluid intothewindow washer
reservoir tank.Donot use the
window washerreservoir tankto
mix thewasher fluidconcentrate
and water.
GUID-B29B EC73-37B3- 4C87-9A9D-EA 809C865599
. Keep thebattery surface cleananddry.
Clean thebattery withasolution ofbaking
soda andwater.
. Make certain theterminal connections are
clean andsecurely tightened.
. Ifthe vehicle isnot tobe used for30 days or
longer, disconnect thenegative 7battery
terminal cabletoprevent discharging it.
NO TE:
Care should betaken toavoid situations
that canlead topotential batterydischarge
and potential no-startconditions suchas:
1. Installation orextended useofelectro-
nic accessories thatconsume battery
power whentheengine isnot running
(Phone chargers, GPS,DVDplayers,
etc .)
2. Vehicle isnot driven regularly and/or
only driven shortdistances.
In these cases, thebattery mayneed tobe
charged tomaintain batteryhealth.
WARNING
. Donot expose thebattery toflames
or electrical sparks.Hydrogen gas
generated bythe battery isexplo-
sive. Donot allow battery fluidto
Maintenance anddo-it-yo urself
8-13
BA TTER Y
&RQGLWLRQ


> (GLW   0RGHO )'@
JUMP STARTING
GUID-C37 C3C0F-280C -4F1D-904A-46ACD5752008
If jump starting isnecessary ,see ªJump startingº
(P .6-8) .If the engine doesnotstart byjump
starting, thebattery mayhave tobe replaced.
Contact aNISSAN dealer.
GUID-0A40 E5F3-EC90-4F03-B955- 4274A23D7967
CAUTION
. Do not ground accessories directly
to the battery terminal. Doingsowill
bypass thevariable voltagecontrol
system andthevehicle battery may
not charge completely.
. Use electrical accessories withthe
engine running toavoid discharging
the vehicle battery.
The variable voltagecontrolsystem measures
the amount ofelectrical discharge fromthe
battery andcontrols voltagegenerated bythe
generator.
GUID-1AF 74337-E57 8-4C98-A7 ED-F2206E 4170AC
SDI1881
1. Alternator
2. Drive beltauto-tensioner
3. Crankshaft pulley
4. Airconditioner compressor
5. Water pump
WARNING
Be sure theignition switchisin the OFF
or LOCK position beforeservicing drive
belts. Theengine couldrotate unex-
pectedly.
1. Visually inspectthebelt forsigns ofunusual
wear, cuts,fraying orlooseness. Ifthe belt is
Maintenance anddo-it-yo urself
8-15
V ARIABLE VOLTAGE CONTROL
S Y STEM DRIVE
BELT
&RQGLWLRQ


> (GLW   0RGHO )'@
8-16
Maintenance anddo-it-yours elf
in poor condition orloose, haveitreplaced
or adjusted byaNISSAN dealer.
2. Have thebelt condition checkedregularly.
GUID-A AF18895-9 2AC-4601-BD 68-201C81BA 060E
WARNING
Be sure theengine andignition switch
are offand that theparking brakeis
engaged securely.
CAUTION
Be sure touse thecorrect socketto
remove thespark plugs. Anincorrect
socket candamage thespark
plugs.
SDI2670
REPLACING SPARK PLUGS
GUID-C62 B4C9C-0259-481F-A 5AB-DFBBB3 D10B69
If replacement isrequired, seeaNISSAN dealer
for servicing.
Iridium platinum-tippe dspark plugs
GUID-E12E 20CD-D386 -439E-A361-4 3DA33D9C4A6
It is not necessary toreplace theiridium
platinum-tipped sparkplugs asfrequently as
the conventional typespark plugs sincetheywill
last much longer. Followthemaintenance log
shown inthe ªNISSAN ServiceandMainte-
nance Guideº.Do not reuse theiridium plati-
num-tipped sparkplugs bycleaning or
regapping.
Always replace sparkplugswithrecom-
mended orequivalent ones.
SP ARK PLUGS
&RQGLWLRQ


> (GLW   0RGHO )'@
GUID-A 7EFD3D5-898 3-4D24-A2FC-51D31 347536E
SDI2667
T o remove thefilter, pulltheairduct
*
1
upward
to remove it.Pull thetabs
*
2
, then pullthe
cover
*
3
upward.
The aircleaner filtershould notbecleaned and
reused. Replace itaccording tothe maintenance
shown inthe ªNISSAN ServiceandMainte-
nance Guideº.When replacing thefilter, wipe
the inside ofthe aircleaner housing andthe
cover withadamp cloth.
WARNING
. Operating theengine withtheair
cleaner removed cancause youor
others tobe burned. Theaircleaner not
only cleans theair,itstops
flame ifthe engine backfires. Ifit
is not there, andtheengine back-
fires, youcould beburned. Donot
drive withtheaircleaner removed,
and becareful whenworking onthe
engine withtheaircleaner removed.
. Never pourfuelinto thethrottle
body orattempt tostart theengine
with theaircleaner removed. Doing
so could result inserious injury.
Maintenance anddo-it-yo urself
8-17
AIR CLEANER
&RQGLWLRQ


> (GLW   0RGHO )'@
8-18
Maintenance anddo-it-yours elf
GUID-5D3 853F1-457C-4 3BF-BB0B-081E44A4FA78
CLEANING
GUID-49071C BE-D68E-45DF-B0FB-4E 24EC69E48E
If your windshield isnot clear afterusing the
windshield washerorifa wiper blade chatters
when running, waxorother material maybeon
the blade orwindshield.
Clean theoutside ofthe windshield witha
washer solution oramild detergent. Your
windshield isclean ifbeads donot form when
rinsing withclear water.
Clean eachblade bywiping itwith acloth
soaked inawasher solution oramild detergent.
Then rinsetheblade withclear water. Ifyour
windshield isstill notclear aftercleaning the
blades andusing thewiper, replace theblades.
CAUTION
Worn windshield wiperblades can
damage thewindshield andimpair
driver
vision.
SDI1803
REPLACING
GUID-3AFC6 7FF-FD24-43FF-A0BD-093F6A3B2 436
Replace thewiper blades ifthey areworn.
Before replacing thewiper blades, thewiper
should beinthe fully upposition toavoid
scratching theengine hoodordamaging the
wiper arm.To pull upthe wiper arm,see
ªWindshield wiperandwasher switchº (P.2-32) .
1. Liftthe wiper armaway fromthewindshield.
2. Push andhold therelease tab
*
A
, and
move thewiper blade downthewiper arm
*
1
.
3. Insert thenew wiper blade ontothewiper
arm until aclick sounds. 4.
Rotate thewiper blade sothat thedimple is
in the groove.
CAUTION
. After wiper blade replacement, re-
turn thewiper armtoits original
position; otherwise itmay beda-
maged whenthehood isopened.
. Make surethewiper blades contact
the glass; otherwise thearm may be
damaged fromwind pressure.
WINDSHIELD WIPERBLADES
&RQGLWLRQ