2015 NISSAN GT-R tow

GTR-10GT-R Overview
.Drive with the suspension setup swit�fh in
the COM�b mode to allow more suspension
stroke.
600 to 1,200 miles (1,000 to 2,000 km):
. Drive with the engine speed kept relatively
high with the shift lever in the
&Mposition.
Shifting is re�fommended between 1st and
4th gears.
. Avoid unne�fessary qui�fk steering and
abrupt braking.
. Drive with the suspension setup swit�fh in
the COM�b mode to allow more suspension
stroke.
Even though the mileage rea�fhes over 1,200
miles (2,000 km) , the �flut�fh may take longer to
properly engage if the vehi�fle is mainly driven in
town at a low speed. NISSAN re�fommends
breaking in the �flut�fh at a GT-R �fertified
NISSAN dealer. Always perform the transmis-
sion setting after breaking in the �flut�fh. If the
transmission setting is not �fomplete, ex�fessive
loads may be applied to the transmission and
power train system parts during starting and
shifting, whi�fh may result in a malfun�ftion or
damage.
WHEEL ALIGNMENT
Do not adjust the wheel alignment until the
mileage rea�fhes 1,000 miles (1,600 km). Until
then, the suspension may not engage enough
and the height may be higher.
However, make sure to adjust the alignment
after 1,000 miles (1,600 km) .
The wheel alignment �fan be adjusted by a GT-R
�fertified NISSAN dealer in a�f�fordan�fe with
spe�fifi�fations for �fity driving to high perfor-
man�fe driving.
The tires on the GT-R may have different wear
rates and wear patterns in �fomparison to
�fonventional passenger vehi�fles. Conta�ft a
GT-R �fertified NISSAN dealer to �fonfirm that
the alignment is within spe�fifi�fations.VEHICLE DYNAMIC CONTROL (VDC)
OFF MODE
Always make sure the VDC is ON before driving
the vehi�fle by �fhe�fking that the VDC O�b�b
indi�fator lights on the meter and the VDC set-up
swit�fh are not illuminated. The GT-R is a high
performan�fe vehi�fle and the VDC must be on/
a�ftivated to provide proper powertrain operation
and intended drivability.
WARNING
. The VDC OFF mode should ONLY be
used briefly to help free the vehicle
if stuck in snow or mud by tempora-
rily stopping operation of the VDC
to maintain wheel torque.
. Driving the GT-R with the VDC off
may lead to handling issues related
to steering maneuvers, acceleration,
or deceleration. Moreover, driving
with the VDC off can result in an
inoperative vehicle by causing ser-
ious damage to the powertrain,
including damage to the Transaxle
Assembly including Transfer, Clutch,
Gears, Transaxle case and all of its
components and other drivetrain
PRECAUTIONS BEFORE DRIVING

Outboard position
3. The booster seat should be positioned onthe vehicle seat so that it is stable. �ff the
seating position is interfering with the proper
booster seat fit�b try another seating position
or a different booster seat.
4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to
follow the booster seat manufacturer’s
instructions for adjusting the belt routing.
5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack.
Be sure the shoulder belt is positioned
across the top�b middle portion of the child’s
shoulder. Be sure to follow the booster seat manufacturer’s instructions for adjusting the
belt routing.
Front seat
6. Follow the warnings�b cautions and instruc-
tions for properly fastening a seat belt.
(
“Three-point type seat belt with re-
tractor” page 1-9)
Safety — Seats, seat belts and supplemental restraint system1-33

1-44Safety — Seats, seat belts and supplemental restraint system
bag system and result in serious
personal injury.
. Immediately after inflation, several
front air bag system components
will be hot. Do not touch them; you
may severely burn yourself.
. No unauthorized changes should be
made to any components or wiring
of the supplemental air bag system.
This is to prevent accidental infla-
tion of the supplemental air bag or
damage to the supplemental air bag
system.
. Do not make unauthorized changes
to your vehicle’s electrical system,
suspension system or front end
structure. This could affect proper
operation of the front air bag sys-
tem.
. Tampering with the supplemental
air bag system may result in serious
personal injury. Tampering includes
changes to the steering wheel and
the instrument panel assembly by
placing material over the steering
wheel pad and above the instrument
panel or by installing additional trim
material around the air bag system. .
Modifying or tampering with the
front passenger seat may result in
serious personal injury. For exam-
ple, do not change the front seats by
placing material on the seat cushion
or by installing additional trim ma-
terial, such as seat covers, on the
seat that is not specifically designed
to assure proper air bag operation.
Additionally, do not stow any ob-
jects under the front passenger seat
or the seat cushion and seatback.
Such objects may interfere with the
proper operation of the occupant
classification sensor.
. No unauthorized changes should be
made to any components or wiring
of the seat belt system. This may
affect the front air bag system.
Tampering with the seat belt system
may result in serious personal in-
jury.
. Work on and around the front air
bag system should be done by a
GT-R certified NISSAN dealer. In-
stallation of electrical equipment
should also be done by a GT-R
certified NISSAN dealer. The Sup-
plemental Restraint System (SRS) wiring harnesses* should not be
modified or disconnected. Un-
authorized electrical test equipment
and probing devices should not be
used on the air bag system.
. A cracked windshield should be
replaced immediately by a qualified
repair facility. A cracked windshield
could affect the function of the
supplemental air bag system.
* The SRS wiring harness connectors are
yellow and orange for easy identification.
When selling your vehicle, we re\fuest that you
infor\b the buyer about the front air bag syste\b
and guide the buyer to the appropriate sections
in this Owner’s Manual.

2-6Instruments and controls
SPEEDOMETER
The speedometer indicates the vehicle speed\f
CAUTION
.For cleaning, use a soft cloth, dam-
pened with water. Never use a rough
cloth, alcohol, benzine, thinner or
any kind of solvent or paper towel
with a chemical cleaning agent.
They will scratch or cause discolora-
tion to the lens.
. Do not spray any liquid such as
water on the meter lens. Spraying liquid may cause the system to
malfunction.
ODOMETER/TWIN TRIP OD-
OMETER
The odometer*1indicates the total distance
that the vehicle has been driven\f
The twin trip odometer
*2indicates the
distance of individ\bal trips\f
Changing the display
P\bsh the TRIP A/B RESET switch to change
between trips&Aand&B\f
Resetting the trip odometer
To reset a trip, display the trip that yo\b want to
reset to zero, then p\bsh and hold the TRIP A/B

WARNING
.Your brake system may not be
working properly if the warning light
is on. Driving could be dangerous. If
you judge it to be safe, drive care-
fully to the nearest service station
for repairs. Otherwise, have your
vehicle towed because driving it
could be dangerous.
. Pressing the brake pedal with the
engine stopped and/or low brake
fluid level may increase your stop-
ping distance and braking will re-
quire greater pedal effort as well as
pedal travel.
. If the brake fluid level is below the
minimum or MIN mark on the brake
fluid reservoir, do not drive until the
brake system has been checked at a
GT-R certified NISSAN dealer.
Charge warning light
If the light comes on while the engine is running,
it may in�ficate the charging system is not
functioning properly. Turn the engine off an�f
chec�b the alternator belt. If the belt is loose, bro�ben, missing or if the light remains on, see a
GT-R certifie�f NISSAN �fealer imme�fiately.
NOTICE
Do not continue driving if the alternator
belt is loose, broken or missing.
Engine oil pressure warning
light
This light warns of low engine oil pressure. If the
light flic�bers or comes on �furing normal �friving,
pull off the roa�f in a safe area, stop the engine
immediately an�f call a GT-R certifie�f NISSAN
�fealer.
The engine oil pressure warning light is
not designed to indicate a low oil level.
Check the vehicle information display or
use the dipstick to check the oil level.
(
“Engine oil level �fisplay” page 2-12)
(“Chec�bing engine oil level” page 8-13)
NOTICE
Running the engine with the engine oil
pressure warning light on could cause
serious damage to the engine almost
immediately. Turn off the engine as soon as it is safe to do so.
Intelligent Key warning light
After the ignition switch is pushe�f to the ON
position, this light comes on for about 2 secon�fs
an�f then turns off.
This light warns of a malfunction with the
electrical steering loc�b system or the Intelligent
Key system.
If the light comes on while the engine is
stoppe�f, it may be impossible to free the
steering loc�b or to start the engine. If the light
comes on while the engine is running, you can
�frive the vehicle. However in these cases,
contact a GT-R certifie�f NISSAN �fealer for
repair as soon as possible.
Low tire pressure warning light
Your vehicle is equippe�f with a Tire Pressure
Monitoring System (TPMS) that monitors the tire
pressure of all tires.
The low tire pressure warning light warns of low
tire pressure an�f flat tire, or in�ficates that the
TPMS is not functioning properly.
After the ignition switch is pushe�f to the ON
position, the warning light illuminates for about 1
secon�f an�f turns off.
Instruments and controls2-27

2-32Instruments and controls
and then blinks for 10 se�fonds when the engine
is not running�b it indi�fates that the vehi�fle is not
ready for an emission �fontrol system inspe�ftion/
maintenan�fe test. (
“Readiness for Inspe�f-
tion/Maintenan�fe (I/M) test (US only)” page 9-
20)
Operation:
The malfun�ftion indi�fator light will �fome on in
one of two ways:
. Malfun�ftion indi�fator light on steady — An
emission �fontrol system malfun�ftion has
been dete�fted. Che�fk the fuel-filler �fap. If
the fuel-filler �fap is loose or missing�b tighten
or install the �fap and �fontinue to drive the
vehi�fle. The
light should turn off after a
few driving trips. If thelight does not
turn off after a few driving trips�b have the
vehi�fle inspe�fted by a GT-R �fertified
NISSAN dealer. You do not need to have
your vehi�fle towed to the dealer.
. Malfun�ftion indi�fator light blinking — An
engine misfire has been dete�fted whi�fh may
damage the emission �fontrol system.
To redu�fe or avoid emission �fontrol system
damage:
1) Do not drive at speeds above 45 MPH
(72 km/h) . 2) Avoid hard a�f�feleration or de�feleration.
3) Avoid steep uphill grades.
4) If possible�b redu�fe the amount of �fargo
being hauled or towed.
The malfun�ftion indi�fator light may stop
blinking and remain on.
Have the vehi�fle inspe�fted by a GT-R
�fertified NISSAN dealer. You do not need
to have your vehi�fle towed to the dealer.
NOTICE
Continued vehicle operation without
having the emission control system
checked and repaired as necessary
could lead to poor driveability, reduced
fuel economy, and possible damage to
the emission control system.
Turn signal/hazard indicator
lights
The light flashes when the turn signal swit�fh
lever or hazard swit�fh is turned on.
Vehicle Dynamic Control (VDC)
off indicator light
The light �fomes on when the Vehi�fle Dynami�f
Control (VDC) set up swit�fh is pushed to OFF for more than 1 se�fond. (
“VDC�b transmis-
sion and suspension setup swit�fhes” page 5-
25)
This indi�fates that the vehi�fle dynami�f �fontrol
system and tra�ftion �fontrol system are not
operating. (
“Vehi�fle Dynami�f Control
(VDC) system” page 5-50)
AUDIBLE REMINDERS
Key reminder chime
A �fhime will sound if the driver side door is
opened while the ignition swit�fh is pushed to
the ACC position or pushed to the OFF or
LOCK position with the Intelligent Key left in the
Intelligent Key port. Make sure the ignition
swit�fh is pushed to the OFF position�b and take
the Intelligent Key with you when leaving the
vehi�fle.
Light reminder chime
A �fhime will sound when the driver side door is
opened with the light swit�fh in theorposition and the ignition swit�fh in the ACC�b OFF
or LOCK position.
Turn the light swit�fh off when you leave the
vehi�fle.

USING THE WIPERS
Push the lever down to operate the wiper at the
following speed:
*1\fNT (\fnter\bittent) — inter\bittent operation can
be adjusted by turning the knob toward*A(Slower) or*B(Faster) .
*2Low — continuous low speed operation
*3High — continuous high speed operation
Push the lever up*4to have one sweep
operation of the wiper. NOTE:
.
In the MIST position, the wipers oper-
ate while the lever is lifted up. When
the lever is released, it automatically
returns to the OFF position and the
wipers stop.
. When the speed sensing wiper interval
function is turned on, the intermittent
operation speed varies in accordance
with the vehicle speed. (For example,
when the vehicle speed is high, the
intermittent operation speed will be
faster.) To turn this function on and
off, see the separate Multi Function
Display Owner’s Manual.
. If the wiper operation is interrupted by
snow or ice, the wiper may stop moving
to protect its motor. If this occurs, turn
the wiper switch to the OFF position
and remove the snow or ice on and
around the wiper arms. In approxi-
mately 1 minute, turn the switch on
again to operate the wiper.
USING THE WASHER
Pull the lever toward you to operate the washer.
Then the wiper will also operate several ti\bes.
NOTE:
When the level of washer fluid is low, a
warning display appears on the vehicle
information display. (
“Low washer
fluid warning” page 2-42)
Instruments and controls2-49

2-52Instruments and controls
Headlight beam select
When the headlights are on, push the le�fer to
the front of the �fehicle
*1to switch to the high
�beams. The high-�beam indicator light illumi-
nates. (
“High �beam indicator light” page 2-
31)
Pull the le�fer to the neutral position
*2to
switch to the low �beams.
Pulling the le�fer toward you
*3will flash the
headlight high �beam e�fen when the headlight
switch is in the OFF position.
CAUTION
Use low beams when there are cars
approaching from the opposite direc-
tion, during city driving and at similar
times.
Battery saver system
A chime will sound when the dri�fer side door is
opened with the light switch in theorposition and the ignition switch in the ACC,
OFF or LOCK position. (“Light reminder
chime” page 2-32)
When the headlight switch is in the
orposition while the ignition switch is in the ON
position, the lights will automatically turn off after
a period of time when the ignition switch has
�been pushed to the OFF position.
When the headlight switch remains in the
orposition after the lights automatically turn
off, the lights will turn on when the ignition
switch is pushed to the ON position.
NOTICE
. When you turn on the headlight
switch again after the lights auto-
matically turn off, the lights will not
turn off automatically. Be sure to
turn the light switch to the OFF
position when you leave the vehicle
for extended periods of time, other-
wise the battery will be discharged.
. Never leave the light switch on
when the engine is not running for
extended periods of time even if the
headlights turn off automatically.
Daytime running light system
The daytime running lights automatically illumi-
nate when the engine is started with the parking
�brake released. The daytime running lights
operate with the headlight switch in the OFF
position. Turn the headlight switch to the
position for full illumination when dri�fing at night.
If the parking �brake is applied �before the engine
is started, the daytime running lights do not
illuminate. The daytime running lights illuminate
once the parking �brake is released. The daytime
running lights will remain on until the ignition
switch is pushed to the OFF position.