2015 NISSAN GT-R warning

5-24Starting and driving
when the vehicle is driven, a wheel may
not roll correctly, or the brake pads
could be damaged. If the pads are
damaged, this may reduce the effec-
tiveness of the brake system which
could cause a collision, serious perso-
nal injury or death.
The GT-R uses brake pad mater�fals that have
h�fgh metall�f�b �bontent. The brake pad mater�fal
helps ma�fnta�fn brak�fng performan�be �fn a w�fde
range of weather and dr�fv�fng �bond�ft�fons.
For the f�frst 3,000 m�fles (5,000 km) of the
veh�f�ble’s serv�f�be l�ffe, and for the f�frst 3,000 m�fles
(5,000km) after a brake repla�bement, the brake
pad to brake rotor �blearan�be �fs very small. When
park�fng, apply the park�fng brake and move the
sh�fft lever to the
&Ppos�ft�fon. Idle the eng�fne for
more than 20 se�bonds w�fthout depress�fng the
brake pedal. Th�fs allows the brake pads to move
away from the rotor so the pad does not �bonta�bt
the rotor.
Add�ft�fonally, the brakes must be dry before
park�fng the veh�f�ble after dr�fv�fng on wet roads or
after wash�fng the veh�f�ble. If the roads are wet,
l�fghtly apply the brakes for a short d�fstan�be
before park�fng the veh�f�ble to dry the brakes.
After wash�fng the veh�f�ble, dry the brakes by
dr�fv�fng on a dry road for a few m�fles and apply the brakes normally based on traff�f�b and road
�bond�ft�fons.
The metall�f�b brake pads and brake d�fs�b rotor
may rust together when the brakes are not
appl�fed:
.
If the veh�f�ble �fs not �fdled for 20 se�bonds
w�fthout the brakes appl�fed, or �ff the brakes
are appl�fed when the veh�f�ble �fs shut off, the
rotor and pads �ban rust together, even when
the brake pads are dry.
. If the brakes are wet when the veh�f�ble �fs
parked and the park�fng brake �fs appl�fed for a
long t�fme.
Conta�bt a GT-R �bert�ff�fed NISSAN dealer �ff the
brake pads and brake rotor have rusted
together.
1. Br�fng the veh�f�ble to a �bomplete stop.
2. W�fth the foot brake pedal depressed, apply the park�fng brake.
3. Move the sh�fft lever to the
&Ppos�ft�fon.
4. Che�bk the sh�fft lever pos�ft�fon �fnd�f�bator on the �fnstrument panel to �bonf�frm that the
&P
pos�ft�fon �fs sele�bted.
5. Push the �fgn�ft�fon sw�ft�bh to stop the eng�fne.
WARNING
Before exiting the vehicle, be sure to
move the shift lever to the&Pposition
and stop the engine. If the engine is
running and the shift lever is not in the
&Pposition, the vehicle may start mov-
ing due to partial engagement of the
clutch or to the effects of gravity on a
slope, or the vehicle may suddenly
accelerate due to accidental operation
of the accelerator pedal, possibly caus-
ing an accident.

5-30Starting and driving
Vehicle Dynamic Control (VDC)
Set up modeFeatures
.In addition to t�fe normal mode function�b t�fis mode adjusts front and rear w�feel
power distribution to improve �fandling.
.Wit�f t�fe transmission switc�f in R mode�b t�fe R mode start function can be used.
(“R mode start function” page 5-32)
Normal (lig�ft is off)
.T�fis mode is for use in a broad range of driving conditions�b for routine driving during
fair to rainy weat�fer�b as well as for driving on road surfaces t�fat are slippery due to
snow or ice.
Make sure to use t�fis mode for everyday driving.
.Temporary mode t�fat can be used to free if it is stuck in snow or mud
(Wit�f t�fe transmission switc�f in SAVE mode�b freeing t�fe ve�ficle become easier.)
NOTE:
Always make sure the VDC is ON before driving the vehicle by checking that the VDC OFF
indicator lights on the meter and the VDC set-up switch are not illuminated. The GT-R is a
high performance vehicle and the VDC must be on/activated to provide proper powertrain
operation and intended drivability.
WARNING
. The VDC OFF mode should ONLY be
used briefly to help free the vehicle
if stuck in snow or mud by tempora-
rily stopping operation of the VDC
to maintain wheel torque.
. Driving the GT-R with the VDC off
may lead to handling issues related
to steering maneuvers, acceleration,
or deceleration. Moreover, driving
with the VDC off can result in an
inoperative vehicle by causing ser-
ious damage to the powertrain,
including damage to the Transaxle
Assembly including Transfer, Clutch,
Gears, Transaxle case and all of its
components and other drivetrain
component(s) by overheating or ex-
cessive force.
. Damage to the powertrain or any
drivetrain component(s) that occurs
when there is a record in the Vehicle
Status Data Recorder (VSDR) that
the vehicle was driven with VDC off
during the period when the damage
was incurred is excluded from war-
ranty coverage.

5-32Starting and driving
conditions, and oil consumption by
itself does not necessarily indicate
any malfunction. If your rate of oil
consumption increases suddenly or
without explanation, NISSAN recom-
mends that you have your vehicle
inspected by a GT-R certified NISSAN
dealer.This function enables the d\five\f to sta\ft accel-
e\fation f\fom a stop b\b selecting R mode with the
VDC and t\fansmission setup switch. The engine
output will be maintained at app\foximatel\b 4,000
\fpm. When using the R mode o\f the R mode
sta\ft function, alwa\bs use p\fope\f seating posi-
tion and follow the safet\b inst\fuctions in Section
1 of this manual.
WARNING
.
Failure to follow the warnings and
instruction for the use of this fea-
ture may cause a loss of vehicle
control or a collision which may lead
to serious personal injury or death:
. Make sure to drive carefully within
legal limits.
. Only use this function when you can
guarantee that it is safe to do so,
based on the surrounding traffic
conditions.
. Do not use this function on slippery
or wet roads. This may cause loss of
vehicle control and could result in
an accident.
. The R mode start function has been
developed not only for controlling the engine, transmission and VDC
system, but also the settings of the
suspension and tires. Therefore, any
modification of the vehicle may
disrupt the vehicle’s balance. This
will not only reduce the optimum
performance of the vehicle but may
also cause damage to powertrain
components, including the trans-
mission.
NOTICE
.
When the temperature of the engine
coolant and transmission oil is high
or low, the function cannot be used.
The temperature range in which the
R mode start function can be used:
— Engine coolant: 1408F - 2128F
(608C - 1008C)
— Transmission oil: 1408F - 2668F (608C - 1308C)
. If the R mode start function is used
4 times consecutively, the function
may be disabled and cannot be
turned on to protect the vehicle
system. While the function is dis-
R MODE START FUNCTION

abled, the warning light illuminates.
When the warning light illuminates,
perform cool down driving.
(
“Cool down” page GTR-13)
When the warning light turns off,
the function can be used again.
. The performance of start may vary
depending on the amount of wheel
spin ,or increase and decrease of
the engine output in response to the
outside temperature. (This vehicle
was set up according to the road
surface conditions of the straight
sections of the Sendai Highland
Raceway course in Japan at 598F
(158C) .)
. For safety reasons, VDC control may
activate automatically when driving
on a slippery road surface, such as a
wet road, in order to apply the
brakes or limit the engine output.
. Frequent use of the R mode start
function increases the load on the
powertrain related parts such as the
clutch and transmission compared
to normal driving. In particular, the
clutch will wear out more quickly.
HOW TO USE R MODE START
FUNCTION
1. Move the shift lever to the&Aor&Mposition.
2. Select the R �fode with the trans�fission set�bp switch. (
“VDC, trans�fission and
s�bspension set�bp switches” page 5-25)
3. Select the R �fode with the VDC set�bp switch.
4. Depress the brake pedal fir�fly with yo�br left foot and keep depressing the brake pedal.
5. Depress the accelerator pedal q�bickly to the floor with yo�br right foot while the brake
pedal is depressed. The engine speed will
increase to approxi�fately 4,000 rp�f and
will be �faintained.
6. Within 3 seconds after depressing the accelerator pedal, release the brake pedal.
WARNING
. Be sure the parking brake is fully
released before driving. Failure to
do so can cause brake failure and
lead to an accident.
. Do not release the parking brake
from outside the vehicle.
. Do not use the shift lever in place of
the parking brake. When parking, be
sure the parking brake is fully
engaged.
. Do not leave children unattended in
Starting and driving5-33
PARKING BRAKE

5-34Starting and driving
a vehicle. They could release the
parking brake and cause an acci-
dent.
To apply: Pull the parking brake lever up\f
To release:
1\f Firml\b appl\b the foot brake\f
2\f While pulling up on the parking brake lever slightl\b, push the button
*Aand lower the
lever completel\b\f
3\f Before driving, be sure the brake warning light goes out\f The cruise control allows driving at speeds
above 25 MPH (40 km/h) without keeping \bour
foot on the accelerator pedal\f
WARNING
Do not use the cruise control when
driving under the following conditions.
Doing so could cause a loss of vehicle
control and result in an accident.
.
When it is not possible to keep the
vehicle at a set speed.
. In heavy traffic or in traffic that
varies in speed.
. On winding or hilly roads.
. On slippery roads (rain, snow, ice,
etc.) .
. In very windy areas.
NOTE:
. When the SAVE mode is selected with
the transmission setup switch, the
acceleration and deceleration can be
controlled smoothly. When the SAVE
mode is selected, the maximum setting
speed is lower than the one in the
normal mode. When the vehicle ap- proaches a gentle uphill, there may be
a slight delay as the vehicle returns to
the preset speed. However, the vehicle
will gradually accelerate and return to
the preset speed.
CRUISE CONTROL

PRECAUTIONS ON CRUISE CON-
TROL
.If the cruise control system malfunctions, it
will cancel automatically. �fhe SE�f indicator
will �blink and the cruise control system
warning will appear to warn the driver.
(
“Cruise control system warning” page
2-40)
. If the engine coolant temperature �becomes
excessively high, the cruise control system
will �be canceled automatically.
. If the SE�f indicator �blinks, turn the cruise
control main switch off and contact a G�f-R certified NISSAN dealer.
. �fhe SE�f indicator may sometimes �blink
when the cruise control main switch is
turned on while pushing the RESUME/
ACCELERA�fE, SE�f/COAS�f or CANCEL
switch. �fo properly set the cruise control
system, perform the steps �below in the order
indicated.
STEERING-WHEEL-MOUNTED
CONTROLS
1. MAIN switch
�furns cruise control ON/OFF.
2. SE�f/COAS�f switch (pressed down) Lowers the set vehicle speed.
3. RESUME/ACCELERA�fE switch (pressed up) Raises the set vehicle speed.
4. CANCEL switch
Cancels cruise control.
Starting and driving5-35

5-38Starting and driving
NOTE:
.If cruise control was canceled by press-
ing the cancel switch or by depressing
the brake pedal, the system changes to
standby status.
. If you depress the brake pedal while
pushing the RESUME/ACCELERATE or
SET/COAST switch and reset at the
cruising speed, the cruise control will
be deactivated. Turn the MAIN switch
off once and then turn it on again.
Under the following conditions�f cruise control
will be auto�batically canceled.
. Vehicle speed drops to below approxi�bately
19 MPH (30 k�b/h) .
. Vehicle speed drops to �bore than approxi-
�bately 8 MPH (13 k�b/h) below the set
vehicle speed.
. The shift lever is �boved to a position other
than
&A
F&M.
. VDC operates.
. A tire is spinning.
. There is a �balfunction in the cruise control
syste�b.
WARNING
.Never rely solely on the hill start
assist system to prevent the vehicle
from moving backward on a hill.
Always drive carefully and atten-
tively. Depress the brake pedal
when the vehicle is stopped on a
steep hill. Be especially careful
when stopped on a hill on frozen
or muddy roads. Failure to prevent
the vehicle from rolling backwards
may result in a loss of control of the
vehicle and possible serious injury
or death.
. The hill start assist system is not
designed to hold the vehicle at a
standstill on a hill. Depress the
brake pedal when the vehicle is
stopped on a steep hill. Failure to
do so may cause the vehicle to roll
backwards and may result in a
collision or serious personal injury.
. The hill start assist may not prevent
the vehicle from rolling backwards
on a hill under all load or road
conditions. Always be prepared to
depress the brake pedal to prevent the vehicle from rolling backwards.
Failure to do so may result in a
collision or serious personal injury.
NOTICE
When the vehicle is stopped on a hill,
do not hold the vehicle in place by
depressing the accelerator pedal. Doing
so may cause the clutch to overheat and
result in transmission damage. Use the
brakes to prevent the vehicle from
moving.
The hill start assist syste�b auto�batically keeps
the brakes applied to help prevent the vehicle
fro�b rolling backwards in the ti�be it takes the
driver to release the brake pedal and apply the
accelerator when the vehicle is stopped on a hill.
Hill start assist will operate auto�batically under
the following conditions:
. The shift lever is �boved to a forward or
reverse position.
. The vehicle is stopped co�bpletely on a hill
by applying the brake.
The �baxi�bu�b holding ti�be is 2 seconds. After 2
seconds the vehicle will begin to roll back and
HILL START ASSIST

hill start assist will stop operating completely.
Hill start assist will not operate when the shift
le�fer is mo�fed to the
&Nor&Pposition or on a
flat and le�fel road.
NOTE:
This system does not function when the
Vehicle Dynamic Control VDC) system
warning appears on the vehicle informa-
tion display located in the tachometer.
(
“Vehicle Dynamic Control (VDC) sys-
tem warning” page 2-37)
NOTICE
Follow these recommendations to ob-
tain maximum engine performance and
ensure the future reliability and econo-
my of your new vehicle. Failure to
follow these recommendations may
result in shortened engine life and
reduced vehicle performance.
Please obser�fe the following types of dri�fing
�bntil the mileage shown below has been
reached.
Until 300 miles (500 km):
. Do not depress the accelerator pedal more
than halfway and a�foid rapid acceleration.
. Dri�fe with the engine speed kept at less
than 3,500 RPM.
. A�foid �bnnecessary q�bick steering, abr�bpt
braking and dri�fing on poor roads.
300 to 600 miles (500 to 1,000 km)
. A�foid rapid acceleration in a low gear (1st to
3rd gears) with the accelerator pedal f�blly
depressed. Depress the pedal slowly.
. A�foid �bnnecessary q�bick steering and
abr�bpt braking. .
Dri�fe with the s�bspension set�bp switch in
the COMF mode to allow more s�bspension
stroke.
600 to 1,200 miles (1,000 to 2,000 km)
. Dri�fe with the engine speed kept relati�fely
high with the shift le�fer in the
&Mposition.
Shifting is recommended between 1st and
4th gears.
. A�foid �bnnecessary q�bick steering and
abr�bpt braking.
. Dri�fe with the s�bspension set�bp switch in
the COMF mode to allow more s�bspension
stroke.
E�fen tho�bgh the mileage reaches o�fer 1,200
miles (2,000 km) , the cl�btch may take longer to
properly engage if the �fehicle is mainly dri�fen in
town at a low speed. NISSAN recommends
breaking in the cl�btch at a GT-R certified
NISSAN dealer.
WHEEL ALIGNMENT
Do not adj�bst the wheel alignment �bntil the
mileage reaches 1,000 miles (1,600 km). Until
then, the s�bspension may not engage eno�bgh
and the height may be higher.
Howe�fer, make s�bre to adj�bst the alignment
after 1,000 miles (1,600 km) .
The wheel alignment can be adj�bsted by a GT-R
Starting and driving5-39
BREAK-IN SCHEDULE