2015 MITSUBISHI L200 reset

InstrumentsE00500100876
Type AType B1- Tachometer
2- Speedometer
3- Fuel gauge
4- Odometer/Tripmeter
5- Tripmeter reset button/Daytime dipper button*
6- Water temperature gauge

Instruments
5-02OKTE15E3Instruments and controls5

Speedometer
E00500200880
Indication for km/h
The speedometer indicates the vehicle’s
speed in kilometers per hour (km/h).
Indication for km/h and mph
The speedometer indicates the vehicle’s
speed in miles per hour (mph) and kilometers
per hour (km/h).
Tachometer
E00500300780
The tachometer indicates the engine speed
(r/min). The tachometer can help you obtain
more economical driving and also warns you
of excessive engine speeds.
CAUTIONl When driving, watch the tachometer to make
sure that the engine speed indication does not rise into the red zone (excessive enginerpm).Odometer/Tripmeter
E00500601113
When the ignition switch is in the “ON” posi-
tion, odometer and tripmeter indications are
given.
Type 1Type 2
A- Odometer B- Tripmeter
C- Reset button
Odometer
The odometer indicates the total distance the
vehicle has travelled.
Instruments
5-03OKTE15E3Instruments and controls5

Tripmeter
The tripmeter indicates the distance travelled
during a particular trip or period.
There are two tripmeter displays: TRIP
and .
TRIP
can be used to measure the distance
travelled since the current trip began. At the same time, TRIP
can be used to measure
the distance from an intermediate location.
Every time the reset button (C) is pressed
lightly (less than 1 second), the tripmeter dis-
play changes (between TRIP
and ).
Type 1Type 2
To reset the tripmeter
To return the display to “0”, press the reset
button (C) for more than 1 second. Only the currently displayed value will be reset. IfTRIP
is displayed, for example, only
TRIP
will be reset.
NOTEl Display TRIP and
each have a max-
imum distance of 999.9 km (999.9 miles).
l When disconnecting the battery terminal for
a long time, the memory of tripmeter display
TRIP
and are cleared, and the dis-
play returns to “0”.
Fuel gauge
E00500700902
The fuel gauge indicates the fuel level in the
fuel tank when the ignition switch is in the
“ON” position.
F- Full
E- Empty
NOTEl When the engine on diesel-powered vehicles
fails to operate due to running out of fuel, it may sometimes be difficult to start after re-
fueling. This is due to air entering the fuel
system. Therefore, air must be bled from the system. (Refer to “Bleeding the fuel system” on page 8-05.)
Instruments
5-04OKTE15E3Instruments and controls5

Average fuel consumption
E00518200267
The average fuel consumption during the pe-
riod since the last reset is shown in (A) and
the momentary fuel consumption in (C). The average value of the fuel consumption is
graphed every 5 minutes and the data for up
to 4 hours are shown in (B). When you press
the “MANUAL” function button in the auto reset mode, the mode will be changed to the manual reset mode. When you press the
“AUTO” function button in the manual reset
mode, the mode will be changed to the auto reset mode.
Auto reset modeManual reset mode
NOTEl When you turn the ignition switch to the
“ON” position after turning it from the “ON” position to the “ACC” or “LOCK” po-
sition in the manual reset mode, the auto re- set mode will automatically be selected.
l When the average fuel consumption cannot
be calculated, “--.-” will be shown.
l The average and momentary fuel consump-
tion change depending on the driving condi- tion (road condition, driving behavior, etc.). The indications may differ from the actual
fuel consumption. Therefore, it is recom- mended to use the indications as reference.
l The unit indication can be changed to your
desired setting {km/L, L/100 km, mpg (UK
GALLON), or mpg (US GALLON)}. Refer to “User customization” on page 5-27.
Resetting the average fuel consumption
Press the “RESET” function button to reset
the average fuel consumption indication.
NOTEl The average fuel consumption can be reset
separately for the auto reset mode and forthe manual reset mode.
l When you turn the ignition switch to the
“ON” position about 4 hours (or more) after turning it from the “ON” position to the
“ACC” or “LOCK” position in the auto reset
mode, the average fuel consumption indica-
tion will automatically be reset.Driving range
E00518300095
This value (A) shows the distance (in km or
miles) that can be driven on the fuel remain- ing in the fuel tank. The driving range is
graphed every 5 minutes and the data for up
to 4 hours are shown in (B).
Centre information display*
5-14OKTE15E3Instruments and controls5

NOTElWhen the driving range is 50 km (30 miles)
or less, the display shows “----”.
When it is 3,000 km (2,000 miles) or more,
“3,000 km” or “2,000 miles” will be shown.
l When the driving range cannot be measured,
the display shows “----”.
l The driving range is shown based on the ac-
cumulated fuel consumption data, however,
may be changed depending on the driving condition (road condition, driving behavior, etc.). If the battery terminals are disconnec-
ted, the accumulated fuel consumption data will be erased. It is recommended to use the indication as reference.
l When the vehicle is fueled, the driving range
will be updated. However, if the amount of
fueling is small, the indication may not be
correct. Therefore, fill up the tank as much as possible in case of fueling.
l When the vehicle is stopped on a steep
slope, the value of the driving range may in-
crease. This is caused by the fuel movement inside the tank on the slope and is not
deemed as a failure.Resetting the driving range
Press the “RESET” function button to reset
the driving range plotted in graph.
NOTEl Pressing the “RESET” function button will
not reset the indication (C).
l It is possible to set the display unit to km or
miles.
Refer to “User customization” on page 5-27.Average speed
E00518400126
The average speed during the period since the
last reset is shown in (A) and the momentary speed in (C). The average value of the vehi-cle speed is graphed every 5 minutes and the
data for up to 4 hours are shown in (B).
When you press the “MANUAL” function
button in the auto reset mode, the mode will
be changed to the manual reset mode. When you press the “AUTO” function button in themanual reset mode, the mode will be changed
to the auto reset mode.NOTEl When you turn the ignition switch to the
“ON” position after turning it from the “ON” position to the “ACC” or “LOCK” po-
sition in the manual reset mode, the auto re- set mode will automatically be selected.
l When the average speed cannot be calcula-
ted, “---” will be shown.
Centre information display*
5-15OKTE15E3Instruments and controls5 Auto reset modeManual reset mode

NOTElThe average and momentary speed change
depending on the driving condition (road
condition, driving behavior, etc.). The indi- cations may differ from the actual speed.
Therefore, it is recommended to use the indi-
cations as reference.
l The unit indication can be changed to your
desired setting (km/h or mph).
Refer to “User customization” on page 5-27.
Resetting the average speed
Press the “RESET” function button to reset
the average vehicle speed.
NOTEl The average speed can be reset separately
for the auto reset mode and for the manualreset mode.NOTEl When you turn the ignition switch to the
“ON” position about 4 hours (or more) after turning it from the “ON” position to the
“ACC” or “LOCK” position in the auto reset mode, the average speed indication will au-
tomatically be reset.Outside temperature
E00518501108
The outside temperature is graphed every 5
minutes and the data for up to 4 hours are shown in (A). The current outside tempera-ture is shown in (B).
Resetting the outside temperature
Press the “RESET” function button to reset
the graph of the outside temperature.
NOTEl Depending on factors such as the driving
conditions, the displayed temperature may vary from the actual outside temperature.
l It is possible to set the display unit to °C or
°F.
Refer to “User customization” on page 5-27.Frozen road warning
E00537100021
This shows the temperature outside the vehi-
cle.
Centre information display*
5-16OKTE15E3Instruments and controls5

Resetting the elevation
Press the “RESET” function button to reset
the elevation plotted in graph.
NOTEl Pressing the “RESET” function button will
not reset the indication (C).
l It is possible to set the display unit to m or
ft.
Refer to “User customization” on page 5-27.Barometer
E00518700044
This display shows the atmospheric pressure
at the present location in (A). The atmospher- ic pressure values are graphed every5 minutes and the data for up to 4 hours are
shown in (B).
Resetting the atmospheric pressure
Press the “RESET” function button to reset
the atmospheric pressure plotted in graph.
NOTEl Pressing the “RESET” function button will
not reset the indication (C).
l It is possible to set the display unit to hPa,
mb, kPa, or inHg.
Refer to “User customization” on page 5-27.Calendar
E00518800032
The date is shown. The calendar pattern can
be changed to your desired setting.
Refer to “Changing the calendar setting” on page 5-24.
Clock-only
E00518900033
Only the clock is shown. The time notation
can be changed to your desired setting. (12 hour/24 hour)
Centre information display*
5-18OKTE15E3Instruments and controls5

Changing the clock settings
E00519200121
1. Press the “ADJ” button to select the
clock setting display.
2. It is possible to adjust the clock using
the function buttons.
“H”-Adjust “hour”.
The indication increases by one
hour, every time you lightly press the “H” function button. If you con-tinue pressing the button for about 2 seconds or more, the indication is fast-forwarded, and then the settingis changed to the hour selected.“M”-Adjust “minute”.
The indication increases by one mi-
nute, every time you lightly press
the “M” function button. If you con- tinue pressing the button for about 2 seconds or more, the indication is fast-forwarded, and then the settingis changed to the minute selected.“SET”
-To reset the minutes to zero.
The time is adjusted as described be-
low by pressing the function button
“SET”.
l 10:30-11:29 · · · · change to
11:00
l 11:30-12:29 · · · · change to
12:00
In this occasion, the display flashes twice and then the setting is changed.
Centre information display*
5-20OKTE15E3Instruments and controls5