must be positioned vertically, directly under
the jacking point of the vehicle.
Observe the following when raising the vehi- cle:
R only use the vehicle-specifi cjack that has
been tested and approved by Mercedes-Benz
to rais ethe vehicle. If the jack is used incor-
rectly, it could tip over while the vehicl eis
raised.
R the jack is designed only to rais eand hold the
vehicl efor as hort time while awhee lisb eing
changed. It is not permissibl etouse it to per-
form maintenance work under the vehicle.
R avoi dchanging the whee lonuphill and down-
hill slopes.
R before raising the vehicle, safeguard it from
rolling awaybya pplying the parking brake and
positioning whee lchocks. Do not release the
parking brake while the vehicl eisraised.
R the jack must be placed on afirm, flat and
non-slip surface. On aloose surface, alarge,
flat load-bearing underlay must be used .Ona
slippery surface, anon-slip underlay must be
used ,e.g. rubber mats.
R do not use wooden blocks or similar objects
as ajack underlay.O therwise, the jack willn ot
be abletoa chieve its load-bearing capacity
due to the restricted height.
R make sure that the distance betwee nthe
underside of the tyres and the ground does
not exceed 3cm.
R never place yourh ands or feet under the
raised vehicle.
R do not lie under the vehicle.
R do not start the engine when the vehicl eis
raised.
R do not open or close adoor or the boot lid
when the vehicl eisraised.
R make sure that no persons are present in the
vehicl ewhen the vehicl eisraised.
Vehicles with light-alloy wheels and hub
caps: the whee lbolts are covered by ahub cap.
Before you can unscrew the whee lbolts, you
must remove the hub cap. Two different variants
can be fitted. Vehicles with plastic hub cap:
X To remove: turn the centre cover of hub
cap :anti-clockwis eand remove.
X To fit: before fitting, ensure that hub cap :is
in the open position. To do this, turn the
centre cover anti-clockwise.
X Position hub cap :and turn the centre cover
clockwise until hub cap :engage sphysically
and audibly.
X Make sure that hub cap :is fitted securely. Vehicles with aluminium hub cap:
X To remove: take socket;and whee lwrench
= from the vehicl etool kit (Y page 336).
X Position socket ;on hub cap :.
X Position whee lwrench =on socket ;.
X Using whee lwrench =,turn hub cap :anti-
clockwise and remove it.
X To fit: before fitting, check hub cap :and
the whee larea for dirt and clean if necessary.
X Put hub cap :in position and turn until it is in
the right position.
X Position socket ;on hub cap :.
X Attach whee lwrench =to socket ;and
tighten hub cap :.
The tightening torque must be 25 Nm. Changing
awheel
363Wheelsa nd tyres Z
i
Note
thatthe hu bcap shoul dbetightened
to the specifie dtorque of 25 Nm.Mercedes-
Benz recommends tha tyou have the hu bcap
fitte dataq ualified specialist workshop. X
Using whee lwrench =,l oosent he bolts on
the whee lyou wish to change by abou tone
full turn. Do not unscrew the bolts completely. The jacking points ar
eloc ate djustb ehin dthe
front whee larche sa nd jus tinfront of the rear
whee larche s(arrows).
Mercedes-AMG vehicle sand vehicle swith
AM Gequipment: to protect the vehicl ebody,
the vehicl ehascovers fitte dnext to the jacking
points on the outer sills. X
Mercedes-AMG vehicle
sand vehicles
with AM Gequipment: foldc over ?
upwards. X
Positio njack Bat jacking point A. X
Make sure tha tthe base of the jack is posi-
tioned verticall yunder the jacking point.
X Turn crank Cclockwise unti ljack Bsits
completel yonjacking point A.The base of
the jack must li eevenly on the ground.
X Turn crank Cunti lthe tyr eisraisedam axi-
mu mof3c moff the ground.
Removing awheel !
Mercede
sAMG vehicle swithc eramic-
brak edisc: during remova land repositioning
of the wheel, the whee lrim can strike the
ceramic-brake disc and damage it. Therefore,
take precautions and have asecond person
assist you. Alternatively ,you can us easec-
ond centring pin.
! Do not place whee
lbolts in sand or dirt. The
thread softhe whee lbolts and whee lhubs
could otherwis ebedamaged when the bolts
ar et ightened.
Whe nfitting/removing wheels ,and for as long
as the wheels ar eremoved, avoi dapplyin gany 364
Changin
gawheelWheel sand tyres
