If AdBlue
®
is pumpedo ut of the AdBlue ®
tank,
e.g. during repairw ork, do not use this fluidto
refill the tank. The purity of the fluidc an no lon-
ger be guaranteed.
Capacities The total capacity of the AdBlue
®
tank may vary,
depending on the vehicle equipment. Model Total capacity
All models
8.5 l
or
24.5 l Engine oil
General notes When handling engine oil, observe the important
safety notes on service products (Y page 371).
The quality of the engine oil is decisive for the
function and service life of an engine. After
extensive tests, Mercedes-Benz approves
engine oils that correspond to the current tech-
nical standard.
Therefore, only Mercedes-Benz approved
engine oils may be used in Mercedes-Benz
engines.
Further information on tested and approved
engine oils can be obtained from any Mercedes-
Benz Service Centre. Mercedes-Benz recom-
mends that you have the oil change carried out
at aq ualifieds pecialist workshop. Mercedes-
Benz approval is indicated on the oil container
by the inscription "MB-Freigabe" or "MB-
Approval "and the corresponding designation,
e.g. MB-Freigabe or MB-Approval 229.51. You can call up an overview of approved engine
oils on the Internet at
http://bevo.mercedes-benz.com by entering
the designation, e.g. 229.5.
The table shows which engine oils have been
approved for yourv ehicle.
Petrol engines: in certain countries, different
engine oils can be used,p rovidedthat the main-
tenance intervals are reduced .For more infor-
mation, please contact aqualifieds pecialist
workshop. Petrol engines MB-Freigabe or
MB-Approval All models
229.5
Diesel engines MB-Freigabe or
MB-Approval All models
228.51, 229.31,
229.51, 229.52 Use only SAE 0W-40 or SAE 5W-40 engine oils
for Mercedes-AMG vehicles.
i If the engine oils listed in the table are not
available, you may add the following engine
oils until the next oil change:
R Petrol engines: MB-Freigabe or MB-
Approval 229.1, 229.3 or ACEA A3
R Diesel engines: MB-Freigabe or MB-
Approval 229.1, 229.3, 229.5 or ACEA C3
This must only be addedo nce and the amount
must not be greater than 1.0 l.
Capacities The following values refer to an oil change,
including the oil filter.
Model Replacement
amount Mercedes-AMG
vehicles
9.0 l
C2
20 d
C2 50 d 6.0 l
All other models
7.0 lServicep
roducts and capacities
375Technical data Z
Additives
!
Do no
tuse any additive switht he engin eoil.
This could damag ethe engine. Brak
efluid G
WARNING
The brak efluid continuously absorbs mois-
tur efromt heair. This result sintheboiling
poin toft hebrak efluid lowering .Iftheboiling
poin toft hebrak efluid is to olow, vapour
pockets may for mwhen th ebrakes are sub-
jected to aheav yload. This would impair brak-
ing efficiency. There is ariskofana ccident.
Hav ethe brak efluid renewed at th eprescri-
bed intervals.
When handlin gbrak efluid ,observ ethe impor-
tan tsafet ynotes on servic eproducts
(Y page 371).
The brak efluid chang eintervals can be foun din
th eS ervic eBooklet.
Only use brak efluid approve dbyMercedes-
Benz in accordanc ewithM B-Freig abe or MB-
Approval 331.0.
Information about approve dbrak efluid can be
obtained at any qualified specialis tworkshop or
on th eInterne tat
http://bevo.mercedes-benz.co m.
i Have the brake fluid regularly replaced at a
qualified specialist workshop in accordance
with the replacement intervals and the
replacement confirmed in the Service Book-
let. Coolant
Importan tsafety notes G
WARNING
If antifreeze comes into contact with hot com- ponents in the engine compartment, it may
ignite. There is arisk of fire and injury.
Let the engine cool dow nbefore yo utop up
the antifreeze .Make sur ethat antifreeze is
not spilled next to the filler neck. Thoroughly clea
nthe antifreeze from components before
starting the engine.
! Only ad
dcoolant that has bee npremixed
with the desire dantifreeze protection. You
coul dotherwise damag ethe engine.
Furthe rinformatio noncoolants can be found
in the Mercedes-Benz Specifications for Ser-
vice Products, MB Specifications for Service
Products 310.1, e.g. on the Internet at
http://bevo.mercedes-benz.com .Orcontact
aq ualifie dspecialist workshop.
! Always use
asuitabl ecoolant mixture, even
in countries where hig htemperatures prevail.
Otherwise ,the engine cooling system is not
sufficiently protected from corrosion and
overheating.
i Have the coolant regularly replaced at a
qualified specialist workshop and the replace- ment confirmed in the Service Booklet.
Comply with the important safety precautions
for service products whe nhandling coolant
(Y page 371).
The coolant is amixture of water and anti-
freeze/corrosion inhibitor. It is responsible for
the following:
R anti-corrosion protection
R antifreeze protection
R raising the boiling point
If antifreeze/corrosion inhibito rispresent in the
correct concentration, the boiling point of the
coolant during operation will be approximately
130 †.
The antifreeze concentrate/corrosion inhibitor
concentration in the engine cooling system
should:
R be at least 50%. Thi swillp rotect the engine
cooling system against freezing dow nto
approximatel y-37 †.
R not excee d55% (antifreeze protection down
to -45 †). Hea twillo therwise not be dissipa-
ted as effectively.
Mercedes-Benz recommends an antifreeze/
corrosion inhibito rconcentrate in accordance
with MB Specifications for Service Products
310.1.
i Whe
nthe vehicle is first delivered, it is filled
with acoolant mixtur ethat ensures adequate
antifreeze and corrosion protection. 376
Service products and capacitiesTechnical data
