Black plate (210,1)
5. Press and hold the just-trainedHomeLink button and observe the
indicator light.
If the indicator light stays on constantly,
programming is complete and your
device should activate when the
HomeLink button is pressed and released.
NOTE
To program the remaining two HomeLink
buttons, begin with “Programming ”―step 2.
Do not repeat step 1.
If the indicator light blinks rapidly for
two seconds and then turns to a
constant light, continue with
“ Programming ”steps 6 ―8to complete
the programming of a rolling code
equipped device (most commonly a
garage door opener).
6. At the garage door opener receiver (motor-head unit) in the garage, locate
the “learn ”or “smart ”button. This can
usually be found where the hanging
antenna wire is attached to the motor-
head unit.
7. Firmly press and release the “learn ”or
“ smart ”button. (The name and color of
the button may vary by manufacturer.)
NOTE
There are 30 seconds in which to initiate step
8.
8. Return to the vehicle and firmly press,
hold for two seconds and release the
programmed HomeLink button. Repeat
the “press/hold/release ”sequence a
second time, and, depending on the
brand of the garage door opener (or
other rolling code equipped device),
repeat this sequence a third time to
complete the programming process. HomeLink should now activate your
rolling code equipped device.
NOTE
To program the remaining two HomeLink
buttons, begin with
“Programming ”―step 2.
Do not repeat step 1.
For questions or comments, please contact
HomeLink at www.homelink.com or1-
800-355-3515.
Gate operator/Canadian Programming
Canadian radio-frequency laws require
transmitter signals to “time-out ”(or quit)
after several seconds of transmission ―
which may not be long enough for
HomeLink to pick up the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are
designed to “time-out ”in the same
manner.
If you live in Canada or you are having
difficulties programming a gate operator
by using the “Programming ”procedures
(regardless of where you live), replace
“ Programming HomeLink ”step 3 with
the following:
NOTE
If programming a garage door opener or gate
operator, it is advised to unplug the device
during the “cycling ”process to prevent
possible overheating.
Continue to press and hold the HomeLink
button while you press and release ―
every two seconds (“ cycle ”) your hand-
held transmitter until the frequency signal
has successfully been accepted by
HomeLink. (The indicator light will flash
slowly and then rapidly.) Proceed with
“ Programming ”step 4 to complete.
5-66
Driving Your Mazda
Switches and Controls
MX-5_8EN7-EA-14E_Edition3 Page210
Friday, September 5 2014 3:19 PM
Form No.8EN7-EA-14E
Black plate (211,1)
Operating the HomeLink System
Press the programmed HomeLink button
to operate a programmed device. The
code will continue being transmitted for a
maximum of 20 seconds.
Reprogramming the HomeLink system
To program a device to HomeLink using a
HomeLink button previously trained,
follow these steps:
1. Press and hold the desired HomeLinkbutton. DO NOT release the button.
2. The indicator light will begin to flash after 20 seconds. Without releasing the
HomeLink button, proceed with
“Programming ”- step 2.
Erasing Programmed HomeLink
Buttons
To erase the existing programming from
all three operating channels, press and
hold the two outside buttons (
,)
on the auto-dimming mirror until the
HomeLink indicator light begins to flash
after approximately 20 seconds.
Verify that the programming has been
erased when you resell the vehicle.
Driving Your Mazda
Switches and Controls
5-67
MX-5_8EN7-EA-14E_Edition3 Page211
Friday, September 5 2014 3:19 PM
Form No.8EN7-EA-14E
Black plate (444,1)
F
Flat Tire ............................................... 7-3Changing .................................... 7-11
Instant Mobility System
(IMS) Emergency Flat Tire Repair
Kit ................................................ 7-5
Tool storage .................................. 7-3
Fluids
Classification .............................. 10-4
Owner maintenance ................... 8-16
Fog Lights ......................................... 5-56
Foot Brake .......................................... 5-5
Fuel Filler lid and cap ........................ 3-40
Gauge ......................................... 5-39
Requirements ............................... 4-2
Tank capacity ............................. 10-5
Fuses ................................................. 8-47 Panel description ........................ 8-49
Replacement ............................... 8-47
G
Glove Compartment .......................... 6-83
H
Hazard Warning Flasher .................... 5-59
Hazardous Driving .............................. 4-7
HeadlightsControl ....................................... 5-54
Flashing ...................................... 5-55
High-low beam .......................... 5-55
On reminder ............................... 5-55
HomeLink Wireless Control
System .............................................. 5-60
Hood Release .................................... 3-41
Horn .................................................. 5-59
I
Ignition
Keys ........................................... 3-23
Switch .......................................... 5-2
Immobilizer System
(with Advanced Key) ........................ 3-63
Immobilizer System
(without Advanced Key) ................... 3-67
Indicator Lights ................................. 5-41 Cruise ......................................... 5-52
DSC OFF .................................... 5-52
Headlight high-beam .................. 5-51
KEY ............................................ 5-49
Security ...................................... 5-50
Shift position .............................. 5-51
TCS/DSC ................................... 5-51
Turn-signal/hazard warning ....... 5-52
Inside Trunk Release Lever ............... 3-35
Instrument Cluster ............................. 5-36
Interior Care ...................................... 8-59
Interior Lights ................................... 6-81
J
Jump-Starting .................................... 7-21
K
Keyless Entry System ....................... 3-24
Keys .................................................. 3-23
L
Label Information ............................. 10-2
Lane-Change Signals ........................ 5-56
Light Bulbs Replacement ............................... 8-38
Specifications ............................. 10-6
Lighting Control ............................... 5-54
11-4
Index
MX-5_8EN7-EA-14E_Edition3 Page444
Friday, September 5 2014 3:21 PM
Form No.8EN7-EA-14E
