2015 MAZDA MODEL CX-3 ECU

5–152
Interior Features
Interior Equipment
Centre Console Tray
WARNING
Never use a cup holder to hold hot
liquids while the vehicle is moving:
Using a cup holder to hold hot
liquids while the vehicle is moving is
dangerous. If the contents spill, you
could be scalded.
A cup or small items can be placed on
the centre console tray using the centre
console divider.
The centre console tray is large enough to
place a small item when the centre console
divider is not in use.
Cargo Securing Loops
WARNING
Make sure luggage and cargo is
secured before driving:
Not securing cargo while driving
is dangerous as it could move or be
crushed during sudden braking or a
collision and cause injury.
Use the loops in the luggage compartment
to secure cargo with a rope or net. The
tensile strength of the loops is 196 N (20
kgf, 44 lbf). Do not apply excessive force
to the loops as it will damage them.
$9@&;&&%@&EJUJPOJOEC







*Some models.5–153
Interior Features
Interior Equipment
Cargo Sub-Compartment *
CAUTION

 Do not apply excessive force to
the luggage board when setting it
up. Otherwise, it could deform or
damage the luggage board.
  Return the luggage board to its
original position before driving the
vehicle. If the vehicle is driven with
the luggage board set up, it could
cause an unexpected accident.
The cargo sub-compartment is located
under the luggage mat, and it can be used
to store small items.
1. Lift up the luggage board.
2. Pull the luggage board outward a
little and insert the opposite end into
the holders so that the luggage board
stands.
Luggage board
Holders
3. Lift the luggage mat.
Luggage mat
Cargo sub-compartment
Luggage Board
When using the luggage board in the
upper level
CAUTION
Make sure the luggage board is securely
inserted into the grooves. Otherwise,
the luggage board may detach while the
vehicle is being driven or during sudden
braking resulting in injury or damage to
the luggage board.
Insert the luggage board into the left and
right grooves.
GrooveLuggage board
Luggage board
$9@&;&&%@&EJUJPOJOEC







6–19
Maintenance and Care
Owner Maintenance
Bonnet
WARNING
Always check that the bonnet is closed
and securely locked:
A bonnet that is not closed and securely
locked is dangerous as it could fl y open
while the vehicle is moving and block
the driver's vision which could result in
a serious accident.
Opening the Bonnet
1. With the vehicle parked, pull the
release handle to unlock the bonnet.
Release handle
2. Insert your hand into the bonnet
opening, slide the latch lever to the
right, and lift up the bonnet.
Lever
NOTE
The lever is located a little to the left of
centre when facing the vehicle.
3. Grasp the support rod in the padded
area and secure it in the support rod
hole indicated by the arrow to hold the
bonnet open.
Pad
Clip
Clip
$9@&;&&%@&EJUJPOJOEC







6–20
Maintenance and Care
Owner Maintenance
Closing the Bonnet
1. Check under the bonnet area to make
certain all fi ller caps are in place and all
loose items (e.g. tools, oil containers,
etc.) have been removed.
2. Lift the bonnet, grasp the padded area
on the support rod, and secure the
support rod in the clip. Verify that the
support rod is secured in the clip before
closing the bonnet.
Clip
Clip
Clip
3. Lower the bonnet slowly to a height of
about 20 cm (7.9 in) above its closed
position and then let it drop.
CAUTION
When closing the bonnet, do not push
it excessively such as by applying your
weight. Otherwise, the bonnet could be
deformed.
$9@&;&&%@&EJUJPOJOEC







6–30
Maintenance and Care
Owner Maintenance
SKYACTIV-D 1.5
Cooling system cap Coolant reservoir
Cooling fan
If it is at or near L, add enough coolant to
the coolant reservoir to provide freezing
and corrosion protection and to bring the
level to F or FULL.
Securely tighten the coolant reservoir tank
cap after adding coolant.
CAUTION
  Radiator coolant will damage paint.  Rinse it off quickly if spilled.


 Use only soft (demineralised) water
in the coolant mixture. Water that
contains minerals will cut down on
the coolant's effectiveness.
  Do not add only water. Always add a
proper coolant mixture.
  The engine has aluminium parts and
must be protected by an ethylene-
glycol-based coolant to prevent
corrosion and freezing.
  DO NOT USE coolants Containing
Alcohol, methanol, Borate or
Silicate.
 These coolants could damage the
cooling system.
  DO NOT MIX alcohol or methanol
with the coolant. This could damage
the cooling system.
CAUTION
  Do not use a solution that contains
more than 60% antifreeze.
 This would reduce effectiveness.
 
 If the “FL22” mark is shown on or
near the cooling system cap, use
of FL-22 is recommended when
replacing engine coolant. Using
engine coolant other than FL-22 may
cause serious damage to the engine
and cooling system.
If the coolant reservoir is empty or new
coolant is required frequently, consult
an expert repairer, we recommend an
Authorised Mazda Repairer.
$9@&;&&%@&EJUJPOJOEC







6–38
Maintenance and Care
Owner Maintenance
Battery Maintenance
To get the best service from a battery:
 


 Keep it securely mounted.



 Keep the top clean and dry.



 Keep terminals and connections clean,
tight, and coated with petroleum jelly or
terminal grease.
 


 Rinse off spilled electrolyte immediately
with a solution of water and baking
soda.
 


 If the vehicle will not be used for an
extended time, disconnect the battery
leads and charge the battery every six
weeks.
Inspecting Electrolyte Level
A low level of electrolyte fl uid will cause
the battery to discharge quickly.
Upper level
Lower level
Inspect the electrolyte level at least once
a week. If it is low, remove the caps and
add enough distilled water to bring the
level between the upper and lower level
(illustration).
Do not overfi ll.
Examine the specifi c gravity of the
electrolyte with a hydrometer, especially
during cold weather. If it is low, recharge
the battery.
Battery Recharging
NOTE
  Before performing maintenance or
recharging the battery, turn off all
accessories and stop the engine.
  To disconnect the battery, remove the
negative lead fi rst. Install it last when
connecting the battery.
  Be sure to remove the caps before
recharging the battery.
 (With i-stop system) Do not quick-charge the battery.




 If the battery quickly discharges
because, for example, the lights were
left on too long with the engine off,
slow-charge it as required by battery
size and charger capacity.
 


 If the battery gradually discharges
because of high electric load while the
vehicle is being used, recharge it as
required by battery size and charger
capacity.
Battery Replacement
Contact an Authorised Mazda Dealer for a
battery replacement purchase.
$9@&;&&%@&EJUJPOJOEC







6–55
Maintenance and Care
Owner Maintenance
3. Pull the fuse straight out with the
fuse puller provided on the fuse block
located in the engine compartment.
4. Inspect the fuse and replace it if it is
blown.
NormalBlown
5. Insert a new fuse of the same amperage
rating, and make sure it fi ts tightly. If
it does not fi t tightly, have an expert
install it. We recommend an Authorised
Mazda Repairer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage the
electric system.
6. Reinstall the cover and make sure that
it is securely installed.
Replacing the fuses under the bonnet
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block under the bonnet. If a fuse is blown,
it must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is
blown, replace it with a new oneof the
same amperage rating .
Normal
Blown
$9@&;&&%@&EJUJPOJOEC







6–56
Maintenance and Care
Owner Maintenance
WARNING
Do not replace the main fuse and
multiplex slow blow fuse by yourself.
Have an Authorised Mazda Repairer
perform the replacement:
Replacing these fuses by yourself
is dangerous because they are high
current fuses. Incorrect replacement
could cause an electrical shock or a
short circuit resulting in a fi re.
4. Reinstall the cover and make sure that
it is securely installed.
$9@&;&&%@&EJUJPOJOEC