2015 MAZDA MODEL CX-3 ECO mode

*Some models.6–66
Maintenance and Care
Appearance Care
Interior Care
WARNING
Do not spray water in the cabin:
Splashing water on electrical parts
such as the audio unit and switches
is dangerous as it could cause a
malfunction or a fi re.
Instrument panel Precautions
Prevent caustic solutions such as perfume
and cosmetic oils from contacting the
instrument panel. They will damage and
discolour the instrument panel. If these
solutions get on the instrument panel, wipe
them off immediately.
CAUTION
Do not use glazing agents.
Glazing agents contain ingredients
which may cause discolouration,
wrinkling, cracks and peeling.
Instrument panel top
 




 When cleaning, it is recommended that
you use a clean towel dampened in a
mild detergent to remove soiling.
 


 If the surface is rubbed harshly, it could
result in the surface being damaged
leaving white scratch marks.
Cleaning the Upholstery and
Interior Trim
Vinyl
Remove dust and loose dirt from vinyl
with a whisk broom or vacuum cleaner.
Clean vinyl with a leather-and-vinyl
cleaner.
Leather
*
Remove dust and sand fi rst using a
vacuum cleaner or other means, then wipe
dirt off using a soft cloth with a leather
cleaner or a soft cloth soaked in mild soap.
Wipe off the remaining cleaner or soap
using a cloth soaked in clean water and
wrung out well.
Remove moisture with a dry, soft cloth
and allow the leather to further dry in a
well-ventilated, shaded area. If the leather
gets wet such as from rain, also remove
moisture and dry it as soon as possible.
NOTE
  Because genuine leather is a natural
material, its surface is not uniform
and it may have natural scars,
scratches, and wrinkles.
  To maintain the quality for as long
as possible, periodical maintenance,
about twice a year, is recommended.
  Sand and dust on the seat surface
may damage the overcoat of the
genuine leather surfaces and
accelerate wear.
  Greasy soiling on genuine leather
may cause molding and stains.
  Rubbing hard with a stiff brush or
cloth may cause damage.
$9@&;&&%@&EJUJPOJOEC







*Some models.6–68
Maintenance and Care
Appearance Care
NOTE

 Do not wipe leather parts using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
or petrol. Otherwise, it may cause
discolouration or stains.
  Scratches or nicks on the panels and
metallic trim resulting from the use
of a hard brush or cloth may not be
repairable.
  Be particularly careful when cleaning
high lustre panels and metallic trim
as they can be easily scratched.
Maintenance of the Active Driving
Display*
The combiner and mirror surface have a
special coating. When cleaning, do not use
a hard or rough-surface cloth, or cleaning
detergent. In addition, if a chemical
solvent gets on the active driving display,
wipe it off immediately. Otherwise, the
combiner and mirror could be damaged
and the surface coating could be scratched.
Use a fi ne, soft cloth such as those used
for cleaning eyeglasses.
Cleaning the Lap/Shoulder Belt
Webbing
Clean the webbing with a mild soap
solution recommended for upholstery or
carpets. Follow instructions. Do not bleach
or dye the webbing; this may weaken it.
After cleaning the belts, thoroughly dry
the belt webbing and make sure there is no
remaining moisture before retracting them.
WARNING
Have an expert repairer, we
recommend an Authorised Mazda
Repairer replace damaged seat belts
immediately:
Using damaged seat belts is dangerous.
In a collision, damaged belts cannot
provide adequate protection.
Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy fi lm, clean them with
glass cleaner. Follow the directions on the
container.
CAUTION
  Do not scrape or scratch the inside of
the window glass. It could damage
the thermal fi laments and the aerial
lines.
  When washing the inside of the
window glass, use a soft cloth
dampened in lukewarm water, gently
wiping the thermal fi laments and the
aerial lines.
 Use of glass cleaning products could
damage the thermal fi laments and the
aerial lines.
$9@&;&&%@&EJUJPOJOEC







*Some models.7–10
If Trouble Arises
Flat Tyre
Emergency Flat Tyre
Repair Kit
*
The emergency fl at tyre repair kit included
with your Mazda is for a temporary repair
of a slightly damaged fl at tyre resulting
from running over nails or similar sharp
objects on the road surface.
Perform the emergency fl at tyre repair
without removing the nail or similar sharp
object which punctured the tyre.
NOTE
Your vehicle is not equipped with a
spare tyre. In the event of a fl at tyre,
use the emergency fl at tyre repair kit
to repair the tyre temporarily. When
doing the repair, refer to the instructions
included in the emergency fl at tyre
repair kit. If an emergency repair was
performed on a fl at tyre using the
emergency fl at tyre repair kit, have
an expert repairer, we recommend an
Authorised Mazda Repairer, repair or
replace the tyre as soon as possible.
About the Emergency Flat Tyre
Repair Kit
The emergency fl at tyre repair kit includes
the following items.
Tyre sealant
Injection hoseCompressorValve core tool
Spare valve core
Speed restriction sticker Instructions
WARNING
Do not allow children to touch the tyre
sealant:
 
 Ingestion of tyre sealant is
dangerous. In the event tyre sealant
is accidentally swallowed, drink
large amounts of water immediately
and seek medical assistance.
  Tyre sealant that comes into contact
with the eyes and skin is dangerous.
If tyre sealant enters the eyes or
contacts the skin, fl ush immediately
with large amounts of water and
seek medical assistance.
$9@&;&&%@&EJUJPOJOEC







7–38
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Power Steering
Malfunction Indicator
Light The light illuminates/fl ashes if the electric power steering has a malfunction.
If the light illuminates/fl ashes, stop the vehicle in a safe place and do not operate the
steering wheel. There is no problem if the light turns off after a while. Contact an
expert repairer, we recommend an Authorised Mazda Repairer if the light illuminates/
fl ashes continuously.
NOTE
If the indicator light illuminates/fl ashes, the power steering will not operate
normally. If this happens, the steering wheel can still be operated, however, the
operation may feel heavy compared to normal, or the steering wheel could vibrate
when turning.
Repeatedly jerking the steering wheel left and right while the vehicle is stopped
or moving extremely slowly will cause the power steering system to go into
protective mode which will make the steering feel heavy, but this does not
indicate a problem. If this occurs, park the vehicle safely and wait several minutes
for the system to return to normal.
Contact Authorised Mazda Repairer and Have Vehicle Inspected
If any of the following warning lights turns on/fl ashes, the system may have a malfunction.
Contact an expert repairer, we recommend an Authorised Mazda Repairer to have your
vehicle inspected.
Signal Warning
Master Warning
Light(Vehicles with type C/type D audio)
The light turns on when the system has a malfunction.
Operate the centre display and verify the content.
Refer to If a Warning Light Turns On or Flashes on page 7-35 .
(Vehicles without type C/type D audio)
The light illuminates continuously if any one of the following occurs. Consult an expert
repairer, we recommend an Authorised Mazda Repairer. There is a malfunction in the battery management system. There is a malfunction in the brake switch. (SKYACTIV-D 1.5)
There is a malfunction in the engine's hydraulic control. There is a malfunction in the engine's timing chain. There is a malfunction in the blow-by heater.
$9@&;&&%@&EJUJPOJOEC







*Some models.7–39
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
ABS Warning Light If the ABS warning light stays on while you're driving, the ABS control unit has detected a
system malfunction. If this occurs, your brakes will function normally as if the vehicle had
no ABS.
Should this happen, consult an expert repairer, we recommend an Authorised Mazda
Repairer as soon as possible.
NOTE
When the engine is jump-started to charge the battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs, it is the result of the weak battery and
does not indicate an ABS malfunction.
Recharge the battery.
(With DSC vehicles)
The brake assist system does not operate while the ABS warning light is illuminated.
Check Engine Light If this light illuminates while driving, the vehicle may have a problem. It is important to
note the driving conditions when the light illuminated and consult an expert repairer, we
recommend an Authorised Mazda Repairer.
The check engine light may illuminate in the following cases:
The engine's electrical system has a problem. The emission control system has a problem. (SKYACTIV-G 2.0)
The fuel tank level being very low or approaching empty. The fuel-fi ller cap is missing or not tightened securely.
If the check engine light remains on, or it fl ashes continuously , do not drive at high speeds
and consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible.
(Amber)
i-stop Warning
Light
*
When the light is turned on
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The light does not turn on when the ignition is switched ON. The light continues to remain on even though the i-stop OFF switch has been pressed
while the engine is running.
When the light is fl ashing
The light continues to fl ash if the system has a malfunction. Have your vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer.
(Amber)
i-ELOOP Warning
Light
*
The light turns on if there is any malfunction in the i-ELOOP system. Consult an expert
repairer, we recommend an Authorised Mazda Repairer.
$9@&;&&%@&EJUJPOJOEC







*Some models.7–40
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Automatic
Transaxle Warning
Light
*
The light illuminates when the transaxle has a problem.
CAUTION
If the automatic transaxle warning light illuminates, the transaxle has an electrical
problem. Continuing to drive your Mazda in this condition could cause damage to your
transaxle. Consult an expert repairer, we recommend an Authorised Mazda Repairer as
soon as possible.
4WD Warning
Light*
When the light is turned on
If the 4WD warning light illuminates, contact an expert repairer, we recommend an
Authorised Mazda Repairer.
Illuminates when there is an abnormality with the 4WD system. Illuminates if there is too much difference in tyre radius between the front and rear wheels.
When the light is fl ashing
Park the vehicle in a safe place. After a few moments, if the warning light stops fl ashing,
you can resume driving. If the light does not stop fl ashing, contact an expert repairer, we
recommend an Authorised Mazda Repairer.
Flashes when the differential oil temperature is abnormally high. Flashes when there is a continuous large difference between front and rear wheel rotation,
such as when trying to pull away from an icy surface or when trying to remove the vehicle
from mud, sand or similar conditions.
Air Bag/Seat Belt
Pretensioner System
Warning Light A system malfunction is indicated if the warning light constantly fl ashes, constantly
illuminates or does not illuminate at all when the ignition is switched ON. If any of these
occur, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible. The system may not operate in an accident. WARNING
Never tamper with the air bag/pretensioner systems and always have an expert
repairer, we recommend an Authorised Mazda Repairer perform all servicing and
repairs:
Self-servicing or tampering with the systems is dangerous. An air bag/pretensioner
could accidentally activate or become disabled causing serious injury or death.
$9@&;&&%@&EJUJPOJOEC







*Some models.7–41
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
(Flashing)
Tyre Pressure
Monitoring System
Warning Light
*
If the tyre pressure monitoring system has a malfunction, the tyre pressure warning
light fl ashes for about 1 minute when the ignition is switched ON and then continues
illuminating. Have your vehicle checked by an expert repairer, we recommend an
Authorised Mazda Repairer as soon as possible.
WARNING
If the tyre pressure monitoring system warning light illuminates or fl ashes, or the tyre
pressure warning beep sound is heard, decrease vehicle speed immediately and avoid
sudden manoeuvring and braking:
If the tyre pressure monitoring system warning light illuminates or fl ashes, or the
tyre pressure warning beep sound is heard, it is dangerous to drive the vehicle at high
speeds, or perform sudden manoeuvring or braking. Vehicle drivability could worsen
and result in an accident.
To determine if you have a slow leak or a fl at, pull over to a safe position where you
can check the visual condition of the tyre and determine if you have enough air
to proceed to a place where air may be added and the system monitored again by
an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair
station.
Do not ignore the TPMS Warning Light: Ignoring the TPMS warning light is dangerous, even if you know why it is
illuminated. Have the problem taken care of as soon as possible before it develops
into a more serious situation that could lead to tyre failure and a dangerous accident.
(Red)
(Illuminate)
KEY Warning Light If any malfunction occurs in the keyless entry system, it illuminates continuously.
CAUTION
If the key warning indicator light illuminates or the push button start indicator light
(amber) fl ashes, the engine may not start. If the engine cannot be started, try starting it
using the emergency operation for starting the engine, and have the vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.
Refer to Emergency Operation for Starting the Engine on page 4-11 .
$9@&;&&%@&EJUJPOJOEC







*Some models.7–42
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
(Illuminate)
Lane Departure
Warning System
(LDWS) Warning
Light
*
The warning light remains turned on if there is a problem with the system. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The LDWS does not operate when the warning light illuminates.
CAUTION
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
When the light remains turned on while driving the vehicle.
When the system is cancelled automatically, the light turns on. Normally, the system
restores automatically and the light turns off, however, if the light remains turned on,
there may be a problem with the system.
The light does not illuminate when the ignition is switched ON. Always use tyres for all wheels that are of the specifi ed size, and the same
manufacture, brand, and tread pattern. In addition, do not use tyres with signifi cantly
different wear patterns on the same vehicle. If such improper tyres are used, the
LDWS may not operate normally.
When an emergency spare tyre is used, the system may not operate normally.
(Amber)
High Beam Control
System (HBC)
Warning Light
*
The light remains turned on if there is a problem with the system. Have your vehicle
inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
NOTE
If the windscreen area in front of the Forward Sensing Camera (FSC) is fogged or
obstructed, the light turns on temporarily. If the light remains turned on, there may be a
problem with the system.
LED Headlight
Warning Light *
This light illuminates if there is a malfunction in the LED headlight. Have your vehicle
inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
(Amber)
Mazda Radar
Cruise Control
(MRCC) Warning
Light
*
The warning light turns on if there is a malfunction in the system while the Mazda Radar
Cruise Control (MRCC) system is on.
Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda
Repairer.
$9@&;&&%@&EJUJPOJOEC