2015 MAZDA MODEL 3 HATCHBACK air condition

*Some models.6–46
Maintenance and Care
Owner Maintenance
Tyre Infl ation Pressure
WARNING
Always infl ate the tyres to the correct
pressure:
Overinfl ation or underinfl ation of tyres
is dangerous. Adverse handling or
unexpected tyre failure could result in
a serious accident.
Refer to Tyres on page 9-13 .
Use only a Mazda-genuine tyre valve
cap:
Use of a non-genuine part is dangerous
as the correct tyre air pressure cannot
be maintained if the tyre valve becomes
damaged. If the vehicle is driven under
this condition, the tyre air pressure
will decrease which could result in a
serious accident. Do not use any part
for the tyre valve cap that is not a
Mazda-genuine part.
Inspect all tyre pressures monthly
(including the spare
* ) when the tyres are
cold. Maintain recommended pressures for
the best ride, handling, and minimum tyre
wear.
Refer to the specifi cation charts (page
9-13 ).
After adjusting the tyre pressure,
initialization of the tyre pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tyre Pressure Monitoring System
Initialization on page 4-164 .
NOTE

 Always check tyre pressure when
tyres are cold.
  Warm tyres normally exceed
recommended pressures. Do not
release air from warm tyres to adjust
the pressure.
  Underinfl ation can cause reduced
fuel economy, uneven and
accelerated tyre wear, and poor
sealing of the tyre bead, which
will deform the wheel and cause
separation of tyre from rim.
  Overinfl ation can produce a harsh
ride, uneven and accelerated tyre
wear, and a greater possibility of
damage from road hazards.
 Keep your tyre pressure at the correct
levels. If one frequently needs
infl ating, have it inspected.
Tyre Rotation
WARNING
Rotate tyres periodically:
Irregular tyre wear is dangerous. To
equalize tread wear for maintaining
good performance in handling and
braking, rotate the tyres every 10,000
km (6,250 miles), or sooner if irregular
wear develops.
During rotation, inspect them for correct
balance.
.B[EB@&'&&"@&EJUJPOJOEC







6–47
Maintenance and Care
Owner Maintenance
NOTE
(Without temporary spare tyre)
Because your vehicle is not equipped
with a spare tyre, you cannot do a tyre
rotation safely with the jack that comes
with your vehicle. Have an expert
repairer, we recommend an Authorised
Mazda Repairer perform tyre rotation.
Do not include (TEMPORARY USE ONLY)
spare tyre in rotation.Forward
Also, inspect them for uneven wear and
damage. Abnormal wear is usually caused
by one or a combination of the following:
 


 Incorrect tyre pressure



 Improper wheel alignment



 Out-of-balance wheel



 Severe braking
After rotation, infl ate all tyre pressures to
specifi cation (page 9-13 ) and inspect the
wheel nuts for tightness.
After adjusting the tyre pressure,
initialization of the tyre pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tyre Pressure Monitoring System
Initialization on page 4-164 .
CAUTION
Rotate unidirectional tyres and radial
tyres that have an asymmetrical tread
pattern or studs only from front to rear,
not from side to side. Tyre performance
will be reduced if rotated from side to
side.
Replacing a Tyre
WARNING
Always use tyres that are in good
condition:
Driving with worn tyres is dangerous.
Reduced braking, steering, and traction
could result in an accident.
Replace all four tyres at the same time:
Replacing just one tyre is dangerous.
It could cause poor handling and poor
braking resulting in loss of vehicle
control. Mazda strongly recommends
that you replace all four tyres at the
same time.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–48
Maintenance and Care
Owner Maintenance
If a tyre wears evenly, a wear indicator
will appear as a solid band across the
tread.
Replace the tyre when this happens.
New treadTread wear indicator
Worn tread
You should replace the tyre before the
band crosses the entire tread.
After adjusting the tyre pressure,
initialization of the tyre pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tyre Pressure Monitoring System
Initialization on page 4-164 .
Temporary Spare Tyre *
Inspect the temporary spare tyre at least
monthly to make sure it is properly
infl ated and stored.
NOTE
The temporary spare tyre condition
gradually deteriorates even if it has not
been used.
The temporary spare tyre is easier to
handle because of its construction which
is lighter and smaller than a conventional
tyre. This tyre should be used only for an
emergency and only for a short distance. Use the temporary spare tyre only until
the conventional tyre is repaired, which
should be as soon as possible.
Refer to Tyre on page 9-13 .
CAUTION
  Do not use your temporary spare
tyre rim with a snow tyre or a
conventional tyre. Neither will
properly fi t and could damage both
tyre and rim.
  The temporary spare tyre has a tread
life of less than 5,000 km (3,000
miles). The tread life may be shorter
depending on driving conditions.
  The temporary spare tyre is for
limited use, however, if the tread
wear solid-band indicator appears,
replace the tyre with the same type of
temporary spare (page 6-48 ).
Replacing a Wheel
WARNING
Always use wheels of the correct size
on your vehicle:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–69
Maintenance and Care
Owner Maintenance
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
19 CNG 15 A —
20 AT 15 A Transaxle control system
21 R.WIPER 15 A Rear window wiper
*
22 A/C 7.5 A Air conditioner
23 ENGINE3 15 A Engine control system
24 ENGINE2 15 A Engine control system
25 ENGINE1 15 A Engine control system
26 GLOW SIG 5 A Engine control system
*
27 EVVT 20 A Engine control system *
28 WIPER 20 A Front window wiper and washer
29 DCDC REG 30 A For protection of various circuits *
30 FUEL PUMP2 30 A —
31 ADD FAN DE 40 A Cooling fan *
32 P.WINDOW1 30 A Power windows
33 H/L LOW R 15 A Headlight low beam (RH) *2
34 H/L LOW L
HID L 15 A Headlight (LH) *1 , Headlight low beam (LH) *2
35 METER1 10 A Instrument cluster
36 IG2 30 A For protection of various circuits
37 LPG 30 A —
38 FAN DE 40 A Cooling fan
*
39 DCDC DE 40 A For protection of various circuits *
40 SRS1 7.5 A Air bag
41 ENGINE. IG1 15 A Engine control system
42 C/U IG1 15 A For protection of various circuits
43 — — —
*1 With xenon fusion headlights
*2 With halogen headlights
.B[EB@&'&&"@&EJUJPOJOEC







7–10
If Trouble Arises
Flat Tyre
6. Shake the sealant bottle to mix the
contents. Then extend the injection
hose.
Injection hose
CAUTION
Do not shake the bottle excessively.
Otherwise, the sealant could spray out
of the injection hose, and if the sealant
contacts clothing or other objects, you
may not be able to remove it.
NOTE
The sealant hardens easily and injecting
it will be diffi cult under cold weather
conditions (0 °C (32 °F) or below).
Warm the sealant inside the vehicle to
facilitate injection. 7. Pull out the compressor hose and
the compressor plug from the air
compressor.
Compressor hose
8. Install the compressor hose which was
pulled out of the air compressor to the
injection valve of the bottle.
Compressor hose Injection hose
Injection
valve
CAUTION
Make sure that the air compressor
switch is OFF before inserting the
compressor hose to the injection valve
of the bottle. If the compressor hose is
not installed to the injection valve of the
bottle securely, the sealant may leak.
.B[EB@&'&&"@&EJUJPOJOEC







7–26
If Trouble Arises
Overheating
Overheating
If the High engine coolant temperature
warning light illuminates, the vehicle loses
power, or you hear a loud knocking or
pinging noise, the engine is probably too
hot.
WARNING
Switch the ignition to off and
make sure the fan is not running
before attempting to work near the
cooling fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running indefi nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Open the bonnet ONLY after steam is
no longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the High engine coolant temperature
warning light illuminates:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic
transaxle in park (P), a manual
transaxle in neutral.
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine compartment.
If steam is coming from the engine
compartment:
Do not go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the bonnet and start the engine.
If neither coolant nor steam is
escaping:
Open the bonnet and idle the engine
until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an expert repairer,
we recommend an Authorised Mazda
Repairer.
6. Make sure the cooling fan is operating,
then turn off the engine after the
temperature has decreased.
7. When cool, check the coolant level.
If it is low, look for coolant leaks from
the radiator and hoses.
.B[EB@&'&&"@&EJUJPOJOEC







7–28
If Trouble Arises
Emergency Towing
Towing Description
We recommend that towing be done only
by an expert repairer, we recommend
an Authorised Mazda Repairer or a
commercial tow-truck service.
Proper lifting and towing are necessary
to prevent damage to the vehicle.
Government and local laws must be
followed.
A towed vehicle usually should have its
drive wheels (front wheels) off the ground.
If excessive damage or other conditions
prevent this, use wheel dollies.
Wheel dollies
When towing with the rear wheels on the
ground, release the parking brake.
CAUTION
  Do not tow the vehicle pointed
backward with driving wheels on
the ground. This may cause internal
damage to the transaxle.
  Do not tow with sling-type
equipment. This could damage your
vehicle. Use wheel-lift or fl atbed
equipment.
If towing service is not available in an
emergency, the vehicle may be towed with
all four wheels on the ground using the
towing hook at the front of the vehicle.
Only tow the vehicle on paved surfaces for
short distances at low speeds.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–36
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
ABS Warning Light If the ABS warning light stays on while you're driving, the ABS control unit has detected a
system malfunction. If this occurs, your brakes will function normally as if the vehicle had
no ABS.
Should this happen, consult an expert repairer, we recommend an Authorised Mazda
Repairer as soon as possible.
NOTE
When the engine is jump-started to charge the battery, uneven rpm occurs and the ABS
warning light may illuminate. If this occurs, it is the result of the weak battery and
does not indicate an ABS malfunction.
Recharge the battery.
(With DSC vehicles)
The brake assist system does not operate while the ABS warning light is illuminated.
Check Engine Light If this light illuminates while driving, the vehicle may have a problem. It is important to
note the driving conditions when the light illuminated and consult an expert repairer, we
recommend an Authorised Mazda Repairer.
The check engine light may illuminate in the following cases:
The fuel tank level being very low or approaching empty. The engine's electrical system has a problem. The emission control system has a problem.
If the check engine light remains on, or it fl ashes continuously , do not drive at high speeds
and consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible.
(Amber)
i-stop warning
light
*
When illuminated
If the i-stop warning light (amber) remains illuminated even after continuously pressing the
i-stop OFF switch under conditions other than when the bonnet is opened or the driver has
exited the vehicle (driver's seat belt is unfastened and driver's door is opened), consult an
expert repairer, we recommend an Authorised Mazda Repairer.
When fl ashing
The light fl ashes if there is any malfunction in the i-stop system. Consult an expert repairer,
we recommend an Authorised Mazda Repairer.
(Amber)
RVM warning light *
This warning light illuminates when the ignition is switched ON. The colour of the light
changes from amber to green when the rear vehicle monitoring system is operable, or
turns off when the system is turned off. The light stays on if the system has a malfunction.
Consult an expert repairer, we recommend an Authorised Mazda Repairer.
NOTE
This warning light may illuminate as a result of a temporary decrease in the sensitivity
of the radar sensor due to bad weather or dirt on the bumper surface. However, this does
not indicate a malfunction.
.B[EB@&'&&"@&EJUJPOJOEC