2015 MAZDA MODEL 3 HATCHBACK ignition

*Some models.4–46
When Driving
Instrument Cluster and Display
Wrench Indicator Light *
When the ignition is switched ON, the
warning light is illuminated and then turns
off after a few seconds.
When illuminated
The wrench indicator light is illuminated
when the preset maintenance period
arrives. Verify the content and perform
maintenance.
Refer to Maintenance Monitor on page
6-15 .
When fl ashing (SKYACTIV-D 2.2)
The sedimentor separates water from the
fuel.
If water accumulates in this fi lter, the
warning light will fl ash. When it does,
consult an expert repairer, we recommend
an Authorised Mazda Repairer as soon as
possible.
Low Engine Coolant Temperature
Indicator Light (Blue)
The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.
If the low engine coolant temperature
indicator light remains illuminated after
the engine has been suffi ciently warmed
up, the temperature sensor could have a
malfunction. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Glow Indicator Light
(SKYACTIV-D 2.2)
This light may illuminate when the
ignition is switched ON.
It turns off when the glow plugs are warm.
If the ignition is left switched ON for a
long period of time without the engine
running after the glow plugs are warmed
up, the glow plugs may warm up again
which will illuminate the glow indicator
light.
.B[EB@&'&&"@&EJUJPOJOEC







4–50
When Driving
Transaxle
Automatic Transaxle Controls
Lock-release button
Indicates the selector lever can be shifted freely into any position.
Indicates that you must hold in the lock-release button to shift.
Indicates that you must depress the brake pedal and hold in the lock-release
button to shift (The ignition must be switched ON).
Various Lockouts:
NOTE
The Sport AT has an option that is not included in the traditional automatic transaxle that
gives the driver the option of selecting each gear instead of leaving it to the transaxle to
shift gears. Even if you intend to use the automatic transaxle functions as a traditional
automatic, you should also be aware that you can inadvertently shift into manual shift
mode and an inappropriate gear may be retained as the vehicle speed increases. If you
notice the engine speed going higher or hear the engine racing, confi rm you have not
accidentally slipped into manual shift mode (page 4-53 ).
.B[EB@&'&&"@&EJUJPOJOEC







4–51
When Driving
Transaxle
Shift Position Indication
The selector position is indicated when the
ignition is switched ON.
Gear position indication
In manual shift mode, the “M” of the shift
position indication illuminates and the
numeral for the selected gear is displayed.
Warning Light
The warning light turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-41 .
Transaxle Ranges
 












 The shift position indicator light in the
instrument cluster illuminates. Refer to
Warning/Indicator Lights on page 4-40 .
 


 The selector lever must be in P or N to
operate the starter.
P (Park)
P locks the transaxle and prevents the front
wheels from rotating.
WARNING
Always set the selector lever to P and
set the parking brake:
Only setting the selector lever to the
P position without using the parking
brake to hold the vehicle is dangerous.
If P fails to hold, the vehicle could
move and cause an accident.
CAUTION
  Shifting into P, N or R while the
vehicle is moving can damage your
transaxle.
  Shifting into a driving gear or reverse
when the engine is running faster
than idle can damage the transaxle.
R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete
stop before shifting to or from R, except
under rare circumstances as explained in
Rocking the Vehicle (page 3-56 ).
N (Neutral)
In N, the wheels and transaxle are not
locked. The vehicle will roll freely even
on the slightest incline unless the parking
brake or brakes are on.
WARNING
If the engine is running faster than
idle, do not shift from N or P into a
driving gear:
It's dangerous to shift from N or P
into a driving gear when the engine
is running faster than idle. If this is
done, the vehicle could move suddenly,
causing an accident or serious injury.
Do not shift into N when driving the
vehicle:
Shifting into N while driving is
dangerous. Engine braking cannot be
applied when decelerating which could
lead to an accident or serious injury.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–52
When Driving
Transaxle
CAUTION
Do not shift into N when driving the
vehicle. Doing so can cause transaxle
damage.
NOTE
Apply the parking brake or depress the
brake pedal before moving the selector
lever from N to prevent the vehicle from
moving unexpectedly.
D (Drive)
D is the normal driving position. From
a stop, the transaxle will automatically
shift through a 4-gear (4-speed transaxle
model)/6-gear (6-speed transaxle model)
sequence.
M (Manual)

M is the manual shift mode position. Gears
can be shifted up or down by operating the
selector lever. Refer to Manual Shift Mode
on page 4-53 .
Active Adaptive Shift (AAS) *
Active Adaptive Shift (AAS)
automatically controls the transaxle shift
points to best suit the road conditions
and driver input. This improves driving
feel. The transaxle may switch to AAS
mode when driving up and down slopes,
cornering, driving at high elevations,
or depressing the accelerator pedal
quickly while the selector lever is in the
D position. Depending on the road and
driving conditions/vehicle operations, gear
shifting could be delayed or not occur,
however, this does not indicate a problem
because the AAS mode will maintain the
optimum gear position.
Shift-Lock System
The shift-lock system prevents shifting out
of P unless the brake pedal is depressed.
To shift from P:
1. Depress and hold the brake pedal.
2. Start the engine.
3. Press and hold the lock-release button.
4. Move the selector lever.
NOTE
  When the ignition is switched to
ACC or the ignition is switched off,
the selector lever cannot be shifted
from P.
  The ignition cannot be switched to
OFF if the selector lever is not in P.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–62
When Driving
Switches and Controls
Lighting Control
Headlights
Turn the headlight switch to turn the headlights, other exterior lights and instrument panel
illumination on or off.
When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.
NOTE
To prevent discharging the battery, do not leave the lights on while the engine is off unless
safety requires them.
Without auto-light control
Without coming home light system
Switch Position
Ignition Position ON ACC or
OFF ON ACC or
OFF ON ACC or
OFF
Headlights — — — — × ×
Running lights
* × — — — — —
Tail lights
Position lights
Number plate lights
Instrument panel illumination — — × × × ×
×: On
—: Off
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–63
When Driving
Switches and Controls
With coming home light system
Switch Position
Ignition Position ON ACC or
OFF ON ACC or
OFF ON ACC or
OFF
Headlights — — — — × ×
Running lights
* × *1 — — — — —
Tail lights
Position lights
Number plate lights
Instrument panel illumination — — × × × ×
*2
×: On
—: Off
*1 It turns on while driving the vehicle.
*2 If the driver's door is opened or 30 s have elapsed with the lights turned on, the lights turn off.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–64
When Driving
Switches and Controls
With auto-light control
Without coming home light system
Switch Position
Ignition Position ON ACC
or OFF ON ACC
or OFF ON ACC
or OFF ON ACC
or OFF
Headlights — — Auto
*1 — — — × ×
Running lights * × — Auto *1 — — — — —
Tail lights
Position lights
Number plate lights
Instrument panel illumination — — Auto
*1 — × × × ×
×: On
—: Off
*1 The headlight and other light settings switch automatically depending on the surrounding brightness detected by
the sensor.
With coming home light system
Switch Position
Ignition Position ON ACC
or OFF ON ACC
or OFF ON ACC
or OFF ON ACC
or OFF
Headlights — — Auto
*1 — — — × —
Running lights * × *2 — Auto *1 — — — — —
Tail lights
Position lights
Number plate lights
Instrument panel illumination — — Auto
*1 × *3 /— *4 × × × × *5
×: On
—: Off
.B[EB@&'&&"@&EJUJPOJOEC







4–65
When Driving
Switches and Controls
*1 The headlight and other light settings switch automatically depending on the surrounding brightness detected by
the sensor.
*2 It turns on while driving the vehicle.
*3 While the lights are turned on, they will remain on even if the ignition is switched to a position other than ON.
If the driver's door is opened or 30 s have elapsed with the lights turned on, the lights turn off.
*4 When the ignition is switched to a position other than ON, the lights will not turn on even if the light switch is
switched to
.
*5 If the driver's door is opened or 30 s have elapsed with the lights turned on, the lights turn off.
Auto-light control
When the headlight switch is in the
position and the ignition is switched ON, the light
sensor senses the surrounding lightness or darkness and automatically turns the headlights,
other exterior lights and instrument panel illumination on or off (see chart above).
CAUTION
  Do not shade the light sensor by adhering a sticker or a label on the windscreen.
Otherwise the light sensor will not operate correctly.

  The light sensor also works as a rain sensor for the auto-wiper control. Keep hands and
scrapers clear of the windscreen when the wiper lever is in the
position and the
ignition is switched ON as fi ngers could be pinched or the wipers and wiper blades
damaged when the wipers activate automatically. If you are going to clean the
windscreen, be sure the wipers are turned off completely — this is particularly
important when clearing ice and snow — when it is particularly tempting to leave the
engine running.
.B[EB@&'&&"@&EJUJPOJOEC