2015 MAZDA MODEL 3 HATCHBACK clock

6–59
Maintenance and Care
Owner Maintenance
Brake lights/Tail lights (Bulb type)
5. Install the new bulb in the reverse order
of the removal procedure.
6. Insert the cover tabs and install the
cover.
Tabs
NOTE
Verify that the cover is securely
installed.(Right side)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the knob and remove the cover.
3. Turn the wing bolt and jack screw
anticlockwise.
4. Remove the jack
5. Turn the socket and bulb assembly
anticlockwise and remove it.
.B[EB@&'&&"@&EJUJPOJOEC







6–60
Maintenance and Care
Owner Maintenance
6. Disconnect the bulb from the socket.
Rear direction indicator lights
Brake lights/Tail lights (Bulb type)
7. Install the new bulb.
8. Insert the wing bolt into the jack with
the jack screw pointing to the down
and turn the wing bolt clockwise to
temporarily tighten it.9. Turn the jack screw in the direction
shown in the fi gure.
10. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suffi ciently tightened.
11. Install the cover in the reverse order of
the removal procedure.
12. Insert the cover tabs and install the
cover.
Tabs
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–61
Maintenance and Care
Owner Maintenance
NOTE
Verify that the cover is securely
installed.
Reverse lights(Saloon), Reverse lights/
Rear fog light (Hatchback)
*
Saloon
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
3. Peel back the boot lid trim.
Removal
Installation
4. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your fi nger and pulling
the connector.
5. Turn the socket and bulb assembly
anticlockwise and remove it.
6. Disconnect the bulb from the socket.
7. Install the new bulb in the reverse order
of the removal procedure.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–62
Maintenance and Care
Owner Maintenance
Hatchback
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the cover.
3. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your fi nger and pulling
the connector.
4. Turn the socket and bulb assembly
anticlockwise and remove it.
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order
of the removal procedure.
Rear fog light (Saloon)
*
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
anticlockwise and remove it.
3. Disconnect the bulb from the socket.
4. Install the new bulb in the reverse order
of the removal procedure.
.B[EB@&'&&"@&EJUJPOJOEC







6–63
Maintenance and Care
Owner Maintenance
Number plate lights
Saloon
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
3. Peel back the boot lid trim.
Removal
Installation
4. Turn the socket and bulb assembly
anticlockwise and remove it.
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order
of the removal procedure. Hatchback
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Wrap a fl athead screwdriver with a soft
cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
fl athead screwdriver.
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse order
of the removal procedure.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–5
If Trouble Arises
Flat Tyre
Jack *
NOTE
Your vehicle may or may not be
equipped with a jack and wheel brace.
For details, consult an Authorised
Mazda Dealer.
To remove the jack
1 . (Saloon)
Push the tabs and remove the cover.
Tabs
(Hatchback)
Turn the knob and remove the cover.
2. Turn the wing bolt and jack screw
anticlockwise.
To secure the jack
1. Insert the wing bolt into the jack with
the jack screw pointing to the down
and turn the wing bolt clockwise to
temporarily tighten it.
2. Turn the jack screw in the direction
shown in the fi gure.
3. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suffi ciently tightened.
.B[EB@&'&&"@&EJUJPOJOEC







7–7
If Trouble Arises
Flat Tyre
CAUTION
  When using the temporary spare
tyre, driving stability may decrease
compared to when using only the
conventional tyre. Drive carefully.
  To avoid damage to the temporary
spare tyre or to the vehicle, observe
the following precautions:
 


 Do not exceed 80 km/h (50 mph).



 Avoid driving over obstacles. Also,
do not drive through an automatic
car wash. This tyre's diameter is
smaller than a conventional tyre,
so the ground clearance is reduced
about 10 mm (0.4 in).
 


 Do not use a tyre chain on this tyre
because it will not fi t properly.




 Do not use your temporary spare
tyre on any other vehicle, it has
been designed only for your
Mazda.
 


 Use only one temporary spare tyre
on your vehicle at the same time.
To remove the spare tyre
1. Lift the boot/luggage compartment mat.
Boot/Luggage compartment mat
2. Turn the spare tyre hold-down bolt
anticlockwise.
Spare tyre hold-down bolt
To secure the spare tyre
Store the spare tyre in the reverse order
of removal. After storing, verify that the
spare tyre is stored securely.
.B[EB@&'&&"@&EJUJPOJOEC







7–16
If Trouble Arises
Flat Tyre
Removing a Flat Tyre
1. If your vehicle is equipped with a
wheel cover, pry off the wheel cover
with the bevelled end of the jack lever.
NOTE
Force the end of the jack lever fi rmly
between wheel and cover, or removal
will be diffi cult.
2. Loosen the wheel nuts by turning them
anticlockwise one turn each, but do not
remove any wheel nuts until the tyre
has been raised off the ground.
3. Place the jack on the ground. 4. Turn the jack screw in the direction
shown in the fi gure and adjust the jack
head so that it is close to the jack-up
position.
Jack head
5. Place the jack under the jack-up
position closest to the tyre being
changed with the jack head squarely
under the jack-up point.
Jacking position
.B[EB@&'&&"@&EJUJPOJOEC