2015 MAZDA MODEL 3 HATCHBACK light

*Some models.6–42
Maintenance and Care
Owner Maintenance
Battery Maintenance
To get the best service from a battery:




 Keep it securely mounted.



 Keep the top clean and dry.



 Keep terminals and connections clean,
tight, and coated with petroleum jelly or
terminal grease.
 


 Rinse off spilled electrolyte immediately
with a solution of water and baking
soda.
 


 If the vehicle will not be used for an
extended time, disconnect the battery
leads and charge the battery every six
weeks.
Inspecting Electrolyte Level *
A low level of electrolyte fl uid will cause
the battery to discharge quickly.
Upper level
Lower level
Inspect the electrolyte level at least once
a week. If it is low, remove the caps and
add enough distilled water to bring the
level between the upper and lower level
(illustration).
Do not overfi ll.
Examine the specifi c gravity of the
electrolyte with a hydrometer, especially
during cold weather. If it is low, recharge
the battery.
Battery Recharging
NOTE
  Before performing maintenance or
recharging the battery, turn off all
accessories and stop the engine.
  To disconnect the battery, remove the
negative lead fi rst. Install it last when
connecting the battery.
  Be sure to remove the caps before
recharging the battery.
 (With i-stop system) Do not quick-charge the battery.




 If the battery quickly discharges
because, for example, the lights were
left on too long with the engine off,
slow-charge it as required by battery
size and charger capacity.
 


 If the battery gradually discharges
because of high electric load while the
vehicle is being used, recharge it as
required by battery size and charger
capacity.
Battery Replacement
Contact an Authorised Mazda Dealer for a
battery replacement purchase.
.B[EB@&'&&"@&EJUJPOJOEC







6–43
Maintenance and Care
Owner Maintenance
Key Battery Replacement
If the buttons on the transmitter are
inoperable and the operation indicator
light does not fl ash, the battery may be
dead.
Replace with a new battery before the
transmitter becomes unusable.
CAUTION
  Make sure the battery is installed
correctly. Battery leakage could
occur if it is not installed correctly.
  When replacing the battery, be
careful not to touch any of the
internal circuitry and electrical
terminals, bend the electrical
terminals, or get dirt in the
transmitter as the transmitter could
be damaged.
  There is the danger of explosion if
the battery is not correctly replaced.
  Dispose of used batteries according
to the following instructions.
 


 Insulate the plus and minus
terminals of the battery using
cellophane or equivalent tape.
 


 Never disassemble.



 Never throw the battery into fi re or
water.
 


 Never deform or crush. 

 Replace only with the same type
battery (CR2025 or equivalent).
The following conditions indicate that the
battery power is low:
 


 The KEY indicator light (green) fl ashes
in the instrument cluster for about 30
seconds after the engine is turned off.
 


 The system does not operate and
the operation indicator light on the
transmitter does not fl ash when the
buttons are pressed.
 


 The system's operational range is
reduced.
Replacing the battery at an Authorised
Mazda Repairer is recommended to
prevent damage to the key. If replacing the
battery by yourself, follow the instruction
below.
Replacing the key battery
1. Press the knob and pull out the
auxiliary key.
Knob
.B[EB@&'&&"@&EJUJPOJOEC







6–44
Maintenance and Care
Owner Maintenance
2. Twist a tape-wrapped fl athead
screwdriver in the direction of the
arrow and open the cover slightly.
Cover
3. Insert the tape-wrapped fl athead
screwdriver into the gap and slide it in
the direction of the arrow.
Cover
Gap
4. Twist the fl athead screwdriver in the
direction of the arrow and remove the
cover.
Cover
5. Remove the battery cap, then remove
the battery.
6. Insert a new battery with the positive
pole facing up, and then cover the
battery with the battery cap.
7. Close the cover.
8. Reinsert the auxiliary key.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–48
Maintenance and Care
Owner Maintenance
If a tyre wears evenly, a wear indicator
will appear as a solid band across the
tread.
Replace the tyre when this happens.
New treadTread wear indicator
Worn tread
You should replace the tyre before the
band crosses the entire tread.
After adjusting the tyre pressure,
initialization of the tyre pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tyre Pressure Monitoring System
Initialization on page 4-164 .
Temporary Spare Tyre *
Inspect the temporary spare tyre at least
monthly to make sure it is properly
infl ated and stored.
NOTE
The temporary spare tyre condition
gradually deteriorates even if it has not
been used.
The temporary spare tyre is easier to
handle because of its construction which
is lighter and smaller than a conventional
tyre. This tyre should be used only for an
emergency and only for a short distance. Use the temporary spare tyre only until
the conventional tyre is repaired, which
should be as soon as possible.
Refer to Tyre on page 9-13 .
CAUTION
  Do not use your temporary spare
tyre rim with a snow tyre or a
conventional tyre. Neither will
properly fi t and could damage both
tyre and rim.
  The temporary spare tyre has a tread
life of less than 5,000 km (3,000
miles). The tread life may be shorter
depending on driving conditions.
  The temporary spare tyre is for
limited use, however, if the tread
wear solid-band indicator appears,
replace the tyre with the same type of
temporary spare (page 6-48 ).
Replacing a Wheel
WARNING
Always use wheels of the correct size
on your vehicle:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident.
.B[EB@&'&&"@&EJUJPOJOEC







6–49
Maintenance and Care
Owner Maintenance
CAUTION
A wrong-sized wheel may adversely
affect:
 
 Tyre fi t 
 Wheel and bearing life 
 Ground clearance 
 Snow-chain clearance 
 Speedometer calibration 
 Headlight aim 
 Bumper height 
 Tyre Pressure Monitoring System
When replacing a wheel, make sure the
new one is the same as the original factory
wheel in diameter, rim width, and offset
(inset/outset).
Proper tyre balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tyres can cause
vibration and uneven wear, such as
cupping and fl at spots.
.B[EB@&'&&"@&EJUJPOJOEC







6–50
Maintenance and Care
Owner Maintenance
Light Bulbs
Saloon HatchbackWith Xenon Fusion Headlights
With Halogen Headlights
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–51
Maintenance and Care
Owner Maintenance
Headlights (Low/High beam)
Running lights
Headlights (Low beam)
Headlights (High beam)/Running lights *
Front fog lights *
Front direction indicator lights
Position lights
Side direction indicator lights
Brake lights (With xenon fusion headlights)
Tail lights (With xenon fusion headlights)
Brake lights/Tail lights (With halogen headlights)
Rear direction indicator lights
Tail lights (With xenon fusion headlights)
Reverse lights
Rear fog light *
Reverse light (Left-hand drive model)
Reverse light (Right-hand drive model)
Rear fog light *1 /Reverse light *2 (Left-hand drive model)
Rear fog light *1 /Reverse light *2 (Right-hand drive model)
High-mount brake light
Number plate lights
Overhead lights (Front)/Map lights
Vanity mirror lights *
Overhead lights (Rear) *
Boot light (Saloon)
Luggage compartment light (Hatchback)
*1 With rear fog light
*2 Without rear fog light
.B[EB@&'&&"@&EJUJPOJOEC







6–52
Maintenance and Care
Owner Maintenance
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer when the replacement is
necessary.
Never touch the glass portion of a
halogen bulb with your bare hands
and always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurised gas. If one is broken, it will
explode and serious injuries could be
caused by the fl ying glass.
If the glass portion is touched with bare
hands, body oil could cause the bulb to
overheat and explode when lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
NOTE
  To replace the bulb, contact an
expert repairer, we recommend an
Authorised Mazda Repairer.
  If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
  Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
Replacing Exterior Light Bulbs
Headlights (With xenon fusion
headlights)
Low/High beam bulbs
You cannot replace the low/high beam
bulbs by yourself. The bulbs must
be replaced at an expert repairer, we
recommend an Authorised Mazda
Repairer.
Headlights (With halogen headlights)
Low-beam bulbs
1. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right, and turn
off engine.
2. Make sure the headlight switch is off.
.B[EB@&'&&"@&EJUJPOJOEC