2015 MAZDA MODEL 3 HATCHBACK turn signal

4–54
When Driving
Transaxle
Indicators
Manual shift mode indication
In manual shift mode, the “M” of the shift
position indication in the instrument panel
illuminates.
Gear position indication
The numeral for the selected gear
illuminates.
Type A
Manual shift mode indication
Gear position indication
Type B
Gear position indication
Manual shift mode indication
Type C
Manual shift mode indicationGear position indication
NOTE
  If the gears cannot be shifted down
when driving at higher speeds, the
gear position indication will fl ash
twice to signal that the gears cannot
be shifted down (to protect the
transaxle).
  If the automatic transaxle fl uid
(ATF) temperature becomes too
high, there is the possibility that the
transaxle will switch to automatic
shift mode, cancelling manual
shift mode and turning off the gear
position indication illumination.
This is a normal function to protect
the AT. After the ATF temperature
has decreased, the gear position
indication illumination turns back on
and driving in manual shift mode is
restored.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–68
When Driving
Switches and Controls
Coming Home Light System *
The coming home light system turns on
the headlights (low beams) when the lever
is operated.
When the lever is pulled with the ignition
switched to ACC or OFF, the low beam
headlights turn on.
The headlights turn off after a certain
period of time has elapsed after the doors
are closed.
NOTE
  The time until the headlights turn off
after the all of the doors are closed
can be changed.
 Refer to Personalisation Features on
page 9-16 .
  If no operations are done for 3
minutes after the lever is pulled, the
headlights turn off.
  The headlights turn off if the lever is
pulled again while the headlights are
illuminated.
Leaving Home Light System *
The leaving home light system turns on
the lights when the key unlock switch is
pressed while away from the vehicle.
When the ignition switch and the
headlight switch are as indicated below,
the headlights will illuminate when the
transmitter unlock button is pressed and
the vehicle receives the transmitter signal.
The headlights turn off after a certain
period of time has elapsed (30 seconds).
 


 Ignition switch: off



 Headlight switch: or
The following lights turn on when the
leaving home light system is operated.
Low beams, Position lights, Tail lights,
Number plate lights
Unlock button
Lock button
NOTE
  Operation of the leaving home light
system can be turned on or off.
 Refer to Personalisation Features on
page 9-16 .
  When the transmitter lock button is
pressed and the vehicle receives the
transmitter signal, the headlights turn
off.
  When the headlight switch is in a
position other than
or , the
headlights turn off.
.B[EB@&'&&"@&EJUJPOJOEC







4–72
When Driving
Switches and Controls
Type B (Without Front Fog Light)
The headlights must be turned on to turn
on the rear fog light.
To turn the rear fog light on, rotate the fog
light switch to the
position (the fog
light switch returns to its original position
automatically).
The rear fog light indicator light in the
instrument cluster illuminates while the
rear fog light is on.
Fog light switch
To turn the rear fog light off, do any of the
following:
 


 Rotate the fog light switch to the
position again (the fog light switch
returns to its original position
automatically).
 


 Turn the headlight switch to the
position.
The rear fog light indicator light in the
instrument cluster goes off when the rear
fog light is turned off.
NOTE
(With auto-light control)
When the headlight switch is in the
position and the headlights, exterior
lights and instrument panel illuminated,
the rear fog light turns on when the rear
fog light switch is turned on.
Turn and Lane-Change
Signals
The ignition must be switched ON to use
the turn and lane-change signals.
Direction Indicators
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to fl ash
after a turn, manually return the lever to its
original position.
Right turn
Left turn Right lane change
Left lane changeOFF
The direction indicators (green) in the
instrument cluster fl ash according to the
operation of the direction indicator lever to
show which signal is working.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–73
When Driving
Switches and Controls
NOTE

 If an indicator light stays on without
fl ashing or if it fl ashes abnormally,
one of the direction indicator bulbs
may be burned out.
  A personalised function is available
to change the turn indicator sound
volume. (page 9-16 )
Lane-Change Signals
Move the lever halfway toward the
direction of the lane change—until the
indicator fl ashes— and hold it there. It will
return to the off position when released.
Three-Flash Turn Signal *
After releasing the direction indicator
lever, the direction indicator fl ashes three
times. The operation can be cancelled by
moving the lever in the direction opposite
to which it was operated.
NOTE
The three-fl ash turn signal function can
be switched to operable/inoperable using
the personalisation function.
Refer to Personalisation Features on
page 9-16 .
Windscreen Wipers and
Washer
The ignition must be switched ON to use
the wipers.
WARNING
Use only windscreen washer fl uid or
plain water in the reservoir:
Using radiator antifreeze as washer
fl uid is dangerous. If sprayed on the
windscreen, it will dirty the windscreen,
affect your visibility, and could result in
an accident.
Only use windscreen washer fl uid
mixed with anti-freeze protection in
freezing weather conditions:
Using windscreen washer fl uid without
anti-freeze protection in freezing
weather conditions is dangerous as it
could freeze on the windscreen and
block your vision which could cause
an accident. In addition, make sure
the windscreen is suffi ciently warmed
using the defroster before spraying the
washer fl uid.
.B[EB@&'&&"@&EJUJPOJOEC







4–81
When Driving
Switches and Controls
NOTE
  The direction indicators do not work
when the hazard warning lights are
on.
  Check local regulations about the use
of hazard warning lights while the
vehicle is being towed to verify that
it is not in violation of the law.
  If the brake pedal is depressed
while driving on slippery roads, the
emergency stop signal system could
operate causing all the turn and lane
change signals to fl ash. Refer to
Emergency Stop Signal System on
page 4-85 .
  While the emergency stop signal
system is operating, all the direction
indicators automatically fl ash rapidly
to caution the driver of a vehicle
following behind your vehicle of a
sudden braking situation. Refer to
Emergency Stop Signal System on
page 4-85 .
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–85
When Driving
Brake
Emergency Stop Signal
System
Your Mazda is equipped with an
emergency stop signal system that is
designed to determine whether you are
depressing the brake pedal with greater
force than during normal braking such
as in a situation requiring emergency
braking. If the system determines that such
a situation is occurring, it fl ashes all the
direction indicators rapidly to caution the
driver of the vehicle following behind your
vehicle of the sudden braking situation.
The system is cancelled when the brake
pedal is released or the system determines
that the brake pedal is no longer heavily
depressed based on the rate at which the
vehicle speed decreases.
NOTE
  If you bring your vehicle to a
complete stop while all the direction
indicators are fl ashing rapidly, the
rapid fl ashing of all the direction
indicators changes back to the
normal fl ashing pattern.

 The emergency stop signal system
does not operate at vehicle speeds
under about 60 km/h (37 mph).
  If the brake pedal is depressed
while driving on slippery roads, the
emergency stop signal system could
operate causing all the turn and lane
change signals to fl ash.
Hill Launch Assist (HLA) *
Hill Launch Assist (HLA) is a function
which assists the driver in accelerating
from a stop while on a slope. When
the driver releases the brake pedal and
depresses the accelerator pedal while
on a slope, the function prevents the
vehicle from rolling. The braking force is
maintained automatically after the brake
pedal is released on a steep grade.
For vehicles with a manual transaxle,
Hill Launch Assist (HLA) operates on a
downward slope when the shift lever is in
the reverse (R) position, and on an upward
slope when the shift lever is in a position
other than the reverse (R) position.
For vehicles with an automatic transaxle,
Hill Launch Assist (HLA) operates on a
downward slope when the shift lever is in
the reverse (R) position, and on an upward
slope when the shift lever is in a forward
gear.
.B[EB@&'&&"@&EJUJPOJOEC







4–167
When Driving
Rear View Monitor
NOTE
  If water, snow, or mud is stuck on the camera lens, wipe it off using a soft cloth. If it
cannot be wiped off, use a mild detergent.
  If the camera temperature changes rapidly (Hot to cold, cold to hot), the rear view
monitor may not operate correctly.
  When replacing the tyres, consult an expert repairer, we recommend an Authorised
Mazda Repairer. Replacing the tyres could result in deviation of the guide lines which
appear on the display.
  If the vehicle's front, side, or rear has been involved in a collision, the alignment of
the rear view parking camera (location, installation angle) may have deviated. Always
consult an expert repairer, we recommend an Authorised Mazda Repairer to have the
vehicle inspected.
  If “No Video Signal Available” is indicated in the display, there could be a problem
with the camera. Have your vehicle inspected at an expert repairer, we recommend an
Authorised Mazda Repairer.
Rear View Parking Camera Location
Rear View Parking Camera Saloon Hatchback
Switching to the Rear View Monitor Display
Shift the shift lever to R with the ignition switched ON to switch the display to the rear view
monitor display.
NOTE
When the shift lever is shifted from R to another shift lever position, the screen returns to
the previous display.
.B[EB@&'&&"@&EJUJPOJOEC







5–23
Interior Features
Audio System
Strong signal noise
This occurs very close to a transmitter
tower. The broadcast signals are extremely
strong, so the result is noise and sound
breakup at the radio receiver.
Station drift noise
When a vehicle reaches the area of two
strong stations broadcasting at similar
frequencies, the original station may be
temporarily lost and the second station
picked up. At this time there will be some
noise from this disturbance.
Station 2
88.3 MHz Station 1
88.1 MHz
Operating Tips for CD Player
Condensation phenomenon
Immediately after turning on the heater
when the vehicle is cold, the CD or
optical components (prism and lens) in
the CD player may become clouded with
condensation. At this time, the CD will
eject immediately when placed in the unit.
A clouded CD can be corrected simply by
wiping it with a soft cloth. Clouded optical
components will clear naturally in about
an hour. Wait for normal operation to
return before attempting to use the unit.
Handling the CD player
The following precautions should be
observed.
 


 Do not use deformed or cracked CDs.
The disc may not eject resulting in a
malfunction.
 


 Do not use non-conventional discs such
as heart-shaped, octagonal discs, etc.
The disc may not eject resulting in a
malfunction.
.B[EB@&'&&"@&EJUJPOJOEC