2015 MAZDA MODEL 3 HATCHBACK reset

*Some models.4–34
When Driving
Instrument Cluster and Display
Outside Temperature Warning *
When the outside temperature is low, the
indication fl ashes and a beep sound is
heard to warn the driver of the possibility
of icy roads.
If the outside temperature is lower than
about 4 °C, the outside temperature
display and the
mark fl ashes for about
ten seconds and a beep sound is heard
once.
NOTE
If the outside temperature is lower than
-20 °C, the beep sound does not operate.
However, the
mark illuminates.
Cruise Control Set Vehicle Speed
Display
The vehicle speed preset using the cruise
control is displayed.
.B[EB@&'&&"@&EJUJPOJOEC







4–35
When Driving
Instrument Cluster and Display
Distance-to-empty Mode
This mode displays the approximate distance you can travel on the remaining fuel based on
the fuel economy.
The distance-to-empty will be calculated and displayed every second.
NOTE
  Even though the distance-to-empty display may indicate a suffi cient amount of
remaining driving distance before refuelling is required , refuel as soon as possible if
the fuel level is very low or the low fuel warning light illuminates.
  The display will not change unless you add more than approximately 9 L (2.3 US gal,
1.9 Imp gal) of fuel.
  The distance-to-empty is the approximate remaining distance the vehicle can be driven
until all the graduation marks in the fuel gauge indicating the remaining fuel supply
disappear.
Average Fuel Economy Mode
This mode displays the average fuel economy by calculating the total fuel consumption
and the total travelled distance since purchasing the vehicle, re-connecting the battery after
disconnection, or resetting the data.
The average fuel economy is calculated and displayed every minute.
To clear the data being displayed, press the INFO button for more than 1.5 seconds. After
pressing the INFO button, - - - L/100 km (- - - mpg) will be displayed for about 1 minute
before the fuel economy is recalculated and displayed.
.B[EB@&'&&"@&EJUJPOJOEC







4–36
When Driving
Instrument Cluster and Display
Current Fuel Economy Mode
This mode displays the current fuel economy by calculating the amount of fuel consumption
and the distance travelled.
Current fuel economy will be calculated and displayed every 2 seconds.
When you've slowed to about 5 km/h (3 mph), - - - L/100 km (- - - mpg) will be displayed.
Average Vehicle Speed Mode
This mode displays the average vehicle speed by calculating the distance and the time
travelled since connecting the battery or resetting the data.
Average vehicle speed will be calculated and displayed every 10 seconds.
To clear the data being displayed, press the INFO button for more than 1.5 seconds. After
pressing the INFO button, - - - km/h (- - - mph) will be displayed for about 1 minute before
the vehicle speed is recalculated and displayed.
Vehicle Speed Alarm
In this mode, the current setting for the vehicle speed alarm is displayed.
You can change the vehicle speed setting at which the warning is triggered.
NOTE
The vehicle speed alarm display is activated at the same time the beep sound is heard. The
set vehicle speed fl ashes several times.
The vehicle speed alarm can be set using the INFO switch.
.B[EB@&'&&"@&EJUJPOJOEC







4–39
When Driving
Instrument Cluster and Display
NOTE
  It may be diffi cult to view the display when wearing sunglasses. Take off your
sunglasses or adjust the luminosity.
  If the battery terminal has been disconnected and re-connected or the battery voltage is
low, the adjusted position may deviate.
  The display may be diffi cult to view or temporarily affected by weather conditions
such as rain, snow, light, and temperature.
  If the audio system is removed, the active driving display cannot be operated.
The active driving display indicates the following information:
 


 Mazda Radar Cruise Control (MRCC) Operation Conditions and Warnings
 Refer to Mazda Radar Cruise Control (MRCC) on page 4-123 .



 Lane Departure Warning System (LDWS) Operation Conditions and Warnings
 Refer to Lane Departure Warning System (LDWS) on page 4-107 .



 Smart Brake Support (SBS) Operation Conditions and Warnings
 Refer to Smart Brake Support (SBS) on page 4-145 .



 Distance Recognition Support System (DRSS) Operation Conditions and Warnings
 Refer to Distance Recognition Support System (DRSS) on page 4-120 .



 Adjustable Speed Limiter Operation Conditions and Warnings
 Refer to Adjustable Speed Limiter on page 4-133 .



 Vehicle Speed Setting Using Cruise Control
 Refer to Cruise Control on page 4-156 .



 Turn-by-Turn (TBT) (Direction and Distance) and Lane Guidance



 Vehicle Speed
Each setting/adjustment for the active driving display can be performed on the centre
display (Type C/Type D audio).
1. Select the (
) icon on the home screen and display the Settings screen.
2. Select the AD-Disp tab.
3. Select the desired item and perform the setting/adjustment.
 

 
Height : Active driving display position


 
Brightness Control : Method for adjusting screen brightness (Automatically/Manually)


 
Calibration : Brightness initialization setting (when selecting automatic adjustment)


 
Brightness : Brightness adjustment (when selecting manual adjustment)


 
Navigation : On/Off


 
Active Driving Display : On/Off


 
Reset
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–46
When Driving
Instrument Cluster and Display
Wrench Indicator Light *
When the ignition is switched ON, the
warning light is illuminated and then turns
off after a few seconds.
When illuminated
The wrench indicator light is illuminated
when the preset maintenance period
arrives. Verify the content and perform
maintenance.
Refer to Maintenance Monitor on page
6-15 .
When fl ashing (SKYACTIV-D 2.2)
The sedimentor separates water from the
fuel.
If water accumulates in this fi lter, the
warning light will fl ash. When it does,
consult an expert repairer, we recommend
an Authorised Mazda Repairer as soon as
possible.
Low Engine Coolant Temperature
Indicator Light (Blue)
The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.
If the low engine coolant temperature
indicator light remains illuminated after
the engine has been suffi ciently warmed
up, the temperature sensor could have a
malfunction. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Glow Indicator Light
(SKYACTIV-D 2.2)
This light may illuminate when the
ignition is switched ON.
It turns off when the glow plugs are warm.
If the ignition is left switched ON for a
long period of time without the engine
running after the glow plugs are warmed
up, the glow plugs may warm up again
which will illuminate the glow indicator
light.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–94
When Driving
Fuel Economy Monitor
Fuel Economy Monitor *
For vehicles with type C/type D audio, the Control Status, Fuel Consumption, and
Effectiveness are switched and displayed by operating each icon in the display.
In addition, after completing a trip, the total energy effi ciency to date is displayed in the
ending display when the ending display is turned on.
1. Select the
icon on the home screen to display the applications screen.
2. Select the “Fuel Economy Monitor”.
3. Operate the commander switch or touch the screen and display the menu.
NOTE
When the menu is displayed by touching the screen, the display is hidden automatically
after 6 seconds.
4. Select the icon in the menu and perform the operation. Each icon operates as follows:
Indication on display Control status
Hides the menu display.
Displays the application screen.
Switches the Fuel Economy Monitor in the order of
Control Status, Fuel Consumption, and
Effectiveness.
Resets the fuel economy data.
Displays the following setting screen. Ending display on/off switching On/off switching for function which synchronizes
reset fuel economy data to trip meter (Trip A)
.B[EB@&'&&"@&EJUJPOJOEC







4–95
When Driving
Fuel Economy Monitor
Fuel Consumption Display
Information regarding the fuel economy is displayed.
Indication on display Control status
Displays the fuel economy for the past 60 minutes. Displays the fuel economy every minute for the
past 1 to 10 minutes.
Displays the fuel economy every 10 minutes for the
past 10 to 60 minutes.
Displays the average fuel economy over the past 5
resets and after the current reset.
Calculates the average fuel economy every minute
after vehicle travel begins, and displays it.
NOTE
  The fuel economy data can be reset by doing the following operation:




 Press the reset switch from the menu screen.



 When the function which synchronizes the fuel economy monitor and the trip meter
is on, reset trip A of the trip meter.
 


 Delete the average fuel economy information displayed in the trip computer. 

 After resetting the fuel economy data, “-- -” is displayed while the average fuel
economy is calculated.
Control Status Display
The i-stop operation status and the i-ELOOP power generating status are displayed.
Indication on display Control status
With i-ELOOP system
Displays the level of electricity generated by
regenerative braking.
Displays the amount of the electricity stored in the
capacitor.
.B[EB@&'&&"@&EJUJPOJOEC







4–158
When Driving
Cruise Control
3. Set the cruise control by pressing the
SET
or SET switch at the desired
speed. The cruise control is set at the
moment the SET
or SET switch is
pressed. Release the accelerator pedal
simultaneously. The cruise set indicator
light (Green) illuminates.
NOTE
  The cruise control speed setting
cannot be performed under the
following conditions:
 


(Automatic transaxle)
 The selector lever is in the P or N
position.
 


(Manual transaxle)
 The shift lever is in the neutral
position.
 


 The parking brake is applied.



(Vehicles with adjustable speed
limiter)
  The ON/OFF switch for the
adjustable speed limiter is pressed.


 Release the SET or SET switch
at the desired speed, otherwise the
speed will continue increasing while
the SET
switch is pressed and
held, and continue decreasing while
the SET
switch is pressed and held
(except when the accelerator pedal is
depressed).
  On a steep grade, the vehicle may
momentarily slow down while
ascending, or speed up while
descending.
NOTE
  Cruise control will cancel if the
vehicle speed decreases below
21 km/h (13 mph) when cruise is
activated, such as when climbing a
steep grade.
  Cruise control may cancel at about
15 km/h (9 mph) below the preset
speed (such as may happen when
climbing a long, steep grade).
To Increase Cruising Speed
Follow either of these procedures.
To increase speed using cruise control
switch
Press the SET
switch and hold it. Your
vehicle will accelerate. Release the switch
at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will increase the
preset speed according to the number of
times it is operated.
Increasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To increase speed using accelerator
pedal
Depress the accelerator pedal to accelerate
to the desired speed. Press the SET
or
SET
switch and release it immediately.
.B[EB@&'&&"@&EJUJPOJOEC