2015 MAZDA MODEL 3 HATCHBACK instrument cluster
[x] Cancel search: instrument clusterPage 158 of 689
4–8
When Driving
Start/Stop Engine
NOTE
After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to
the ON position.
(SKYACTIV-G 1.5, MZR 1.6,
SKYACTIV-G 2.0)
After pressing the push button start
and before the engine starts, the
operation sound of the fuel pump
motor from near the fuel tank can be
heard, however, this does not indicate
a malfunction.
NOTE
(SKYACTIV-D 2.2)
When starting the engine, do
not release the clutch pedal
(manual transaxle) or the brake
pedal (automatic transaxle) until
the glow indicator light in the
instrument cluster turns off and
the engine starts, after pressing the
push button start.
If the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) is released
before the engine starts, depress
the clutch pedal (manual transaxle)
or the brake pedal (automatic
transaxle) again and press the push
button start to start the engine.
If the ignition is left switched ON
for a long period of time without
the engine running after the glow
plugs are warmed up, the glow
plugs may warm up again which
will illuminate the glow indicator
light.
The starter does not rotate until the
glow indicator light turns off.
8. After starting the engine, let it idle
for about ten seconds (Prohibited in
Germany).
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 169 of 689
4–19
When Driving
Start/Stop Engine
NOTE
If any one of the following occurs, the length of time the engine is stopped
automatically could be shorter or the length of time required before i-stop functions
again could be longer.
The ambient temperature is high or low.
The battery power is depleted.
The power consumption of vehicle equipment is high.
The i-stop function does not operate when the ambient temperature is extremely high
or low.
The engine may not stop automatically for a while after the battery leads are
reconnected after temporarily disconnecting them. In addition, if the battery is
replaced, the i-stop system will need to be reset and checked to make sure it operates
correctly. When replacing the battery, consult an expert repairer, we recommend an
Authorised Mazda Repairer.
i-stop OFF Switch
The i-stop function can be turned off by
pressing the switch until the beep sounds
and the i-stop warning light (amber) in the
instrument cluster illuminates. The i-stop
function can be turned back on by pressing
the switch again until the beep sounds and
the i-stop warning light (amber) turns off.
NOTE
If the i-stop function was turned off
using the i-stop OFF switch, the system
will resume operation the next time the
engine is started.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 174 of 689
4–24
When Driving
Instrument Cluster and Display
Meters and Gauges
Type A
Type B
Type C
Steering Switch (Digital Speed Meter Type)
(Analog Speed Meter Type (With Tachometer))
(Analog Speed Meter Type (Without Tachometer))
Some models.
Instrument Cluster
Speedometer .......................................................................................................... page 4-25
Odometer, Trip Meter and Trip Meter Selector .................................................... page 4-25
Tachometer ............................................................................................................ page 4-27
Fuel Gauge ............................................................................................................ page 4-27
Instrument panel Illumination ............................................................................... page 4-28
Outside Temperature Display ................................................................................ page 4-29
Cruise Control Set Vehicle Speed Display ............................................................ page 4-29
Multi Information Display .................................................................................... page 4-32
Active Driving Display ......................................................................................... page 4-38
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 175 of 689
*Some models.4–25
When Driving
Instrument Cluster and Display
Trip Computer and INFO Switch .......................................................................... page 4-30
Speed Unit Selector ............................................................................................... page 4-25
Speedometer
The speedometer indicates the speed of the
vehicle.
Speed Unit Selector (Type A
instrument cluster) *
In some countries, you may have to
change the speed units between km/h and
mph.
Press the speed unit selector for 1.5
seconds or more.
The speed units for the speedometer will
change between km/h and mph.
Speedometer
Speed unit selector
Odometer, Trip Meter and Trip
Meter Selector
The display mode can be changed from
odometer to trip meter A to trip meter B
and then back to odometer by pressing the
selector while one of them is displayed.
The selected mode will be displayed.Type A/Type B
Press the selector
Press the selector
Press the selector Odometer
Trip meter A
Trip meter B
Type C
Press the selector
Press the selector
Press the selector Odometer
Trip meter A
Trip meter B
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 176 of 689
4–26
When Driving
Instrument Cluster and Display
NOTE
When the ignition is switched to ACC
or off, the odometer or trip meters
cannot be displayed, however, pressing
the selector can inadvertently switch
the trip meters or reset them during an
approximate ten-minute period in the
following cases:
After the ignition is switched to off
from ON.
After the driver's door is opened.
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.
For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is fi lled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed. The trip meter records the total distance
the vehicle is driven until the meter
is again reset. Return it to “0.0” by
depressing and holding the selector for
one second or more. Use this meter to
measure trip distances and to compute fuel
consumption.
NOTE
(Vehicles with type C/type D audio) If the fuel economy data is reset
using the fuel economy monitor,
or trip A is reset using the trip
meter when the function which
synchronizes the fuel economy
monitor and the trip meter is on, the
fuel economy data and trip A are
reset simultaneously.
Refer to Fuel Economy Monitor on
page 4-94 .
Only the trip meters record tenths of
kilometres (miles).
The trip record will be erased when:
The power supply is interrupted
(blown fuse or the battery is
disconnected).
The vehicle is driven over 9999.9
km (mile).
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 177 of 689
*Some models.4–27
When Driving
Instrument Cluster and Display
Tachometer *
The tachometer shows engine speed in
thousands of revolutions per minute (rpm).
CAUTION
Do not run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine damage.
Type A
*1The range varies depending on the type
of gauge.*1
Striped zone
*1
Red zone
Type B
*1The range varies depending on the type
of gauge.*1
Striped zone
*1
Red zone
NOTE
When the tachometer needle enters the
STRIPED ZONE, this indicates to the
driver that the gears should be shifted
before entering the RED ZONE.
Fuel Gauge (Without Multi-
information display)
The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4 full.
Digital speed meter type/Type A
instrument cluster/Type B instrument
cluster
Full
1/4 Full
Type C
Full
1/4 Full
If the low fuel warning light illuminates or
the fuel level is very low, refuel as soon as
possible.
Refer to Warning/Indicator Lights on page
4-40 .
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 178 of 689
4–28
When Driving
Instrument Cluster and Display
NOTE
After refuelling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve
since the fuel moves in the tank.
The display indicating a quarter
or less remaining fuel has more
segments to show the remaining fuel
level in greater detail.
The direction of the arrow ()
indicates that the fuel-fi ller fl ap is on
the left side of the vehicle.
(SKYACTIV-D 2.2)
If inconsistency in engine performance
or stalling occurs due to low fuel level
conditions, refuel the vehicle as soon as
possible and add at least 10 L (2.7 US gal,
2.2 Imp gal) of fuel.
Instrument panel Illumination
When the light switch is turned to the
or position with the ignition switched
ON, the brightness of instrument panel
illumination is dimmed.
The brightness of the instrument panel
and instrument panel illuminations can be
adjusted by rotating the knob.
The brightness decreases by rotating the
knob to the left. A beep sound will be
heard when the knob has been rotated to
the maximum dim position.
The brightness increases by rotating the
knob to the right.
Dim
Bright
Function for cancelling illumination
dimmer
The illumination dimmer can be cancelled
by rotating the knob to the right until a
beep sound is heard while the light switch
is in the
or position with the
ignition switched ON. If the instrument
cluster's visibility is reduced due to glare
from surrounding brightness, cancel the
illumination dimmer.
. B [ E B @ & ' & & " @ & E J U J P O J O E C
Page 179 of 689
*Some models.4–29
When Driving
Instrument Cluster and Display
NOTE
When the illumination dimmer is
cancelled, the instrument cluster
cannot be dimmed even if the light
switch is turned to the
or
position. When the illumination dimmer is
cancelled, the screen in the centre
display switches to constant display
of the daytime screen.
Outside Temperature Display
(Without Multi-information
display)
*
When the ignition is switched ON, the
outside temperature is displayed.
NOTE
Under the following conditions, the
outside temperature display may differ
from the actual outside temperature
depending on the surroundings and
vehicle conditions:
Signifi cantly cold or hot
temperatures.
Sudden changes in outside
temperature.
The vehicle is parked.
The vehicle is driven at low
speeds. The outside temperature unit can be
switched between Celsius and Fahrenheit
using the following procedure.
1. Press the INFO button with the ignition
switched off and continue pressing the
INFO button for 5 seconds or longer
while switching the ignition ON. The
outside temperature display fl ashes.
2. Press the up
or down part of the
INFO switch to change the outside
temperature unit.
3. Press and hold the INFO button for 3
seconds or longer while the outside
temperature display is fl ashing. The
outside temperature display illuminates.
Cruise Control Set Vehicle Speed
Display (Without Multi-
information display)
*
The vehicle speed preset using the cruise
control is displayed.
. B [ E B @ & ' & & " @ & E J U J P O J O E C