2015 LEXUS RX450h clock

6574-3. Do-it-yourself maintenance
4
Maintenance and care Holding a rag under the end, pull the dipsti ck out and check the
oil level.
Low
Normal
Excessive
The shape of the dipstick may dif-
fer depending on the type of vehi-
cle or engine.
Wipe the dipstick and reinsert it fully.
■ Adding engine oil
If the oil level is below or near the
low level mark, add engine oil of
the same type as th at already in the
engine.
Make sure to check th e oil type and prepare the items needed before
adding oil.
Remove the oil filler cap by turning it counterclockwise.
Add engine oil slowly, checking the dipstick.
Install the oil filler cap by turning it clockwise.STEP 5
STEP 6
Engine oil
selection  P. 8 0 2
Oil quantity
(Low  Full) 1.6 qt. (1.5 L, 1.3 Imp. qt.)
Items Clean funnel
STEP 1
STEP 2
STEP 3

7114-3. Do-it-yourself maintenance
4
Maintenance and care Turn the bulb base counterclock-
wise.
Replace the light bulb, and install
the bulb base. Align the 3 tabs on the light bulb
with the mounting, and insert.
Turn and secure the bulb base.
Connect the connector. Shake the bulb base gently to
check that it is not loose, turn the
headlight high beams on once and
visually confirm that no light is leak-
ing through the mounting.STEP 2
STEP 3
STEP 4

7124-3. Do-it-yourself maintenance
■ Headlight high beams (vehicles with LED headlights)
Turn the cover counterclockwise
and remove it.
Unplug the connector while pull-
ing the lock release.
Turn the bulb base counterclock-
wise.
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb
with the mounting, and insert.STEP 1
STEP 2
STEP 3
STEP 4

7134-3. Do-it-yourself maintenance
4
Maintenance and care Turn and secure the bulb base.
Connect the connector. Shake the bulb base gently to
check that it is not loose, turn the
headlight high beams on once and
visually confirm that no light is leak-
ing through the mounting.
Turn the cover clockwise.STEP 5
STEP 6

7144-3. Do-it-yourself maintenance
■ Halogen headlight low beams (if equipped)
Turn the bulb base counterclock-
wise.
Unplug the connector while
depressing the lock release.
Replace the light bulb, and install
the bulb base. Align the 3 tabs on the light bulb
with the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to
check that it is not loose, turn the
headlight low beams on once and
visually confirm that no light is leak-
ing through the mounting.STEP 1
STEP 2
STEP 3
STEP 4

7154-3. Do-it-yourself maintenance
4
Maintenance and care ■ Front turn signal light (left side)
Move the fuse box.
Vehicles with LED headlights:
Unplug the connector while
depressing the lock release.
Turn the bulb base counterclock-
wise.
Remove the light bulb.STEP 1
STEP 2
STEP 3
STEP 4

7164-3. Do-it-yourself maintenance
■ Front turn signal light (right side)
Move the washer fluid filler open-
ing.
Turn the bulb base counterclock-
wise.
Remove the light bulb.STEP 1
STEP 2
STEP 3

7174-3. Do-it-yourself maintenance
4
Maintenance and care ■ Rear turn signal and tail lights
Remove the access hole cover. Use a flathead screwdriver
wrapped in a cloth.
Turn the bulb base counterclock-
wise.
Tail light
Rear turn signal light
Remove the light bulb.
Tail light
Rear turn signal lightSTEP 1
STEP 2
STEP 3