2015 LEXUS RX350 low beam

2162-3. Operating the lights and windshield wipers
■
Fog lights can be used when
The headlights are on in low beam. Type B
Turns the front fog
lights off
Turns the front fog
lights on

7104-3. Do-it-yourself maintenance
46
FILTER 10 A47
IG1 MAIN 30 A ECU-IG1 NO. 6, BK/UP LP, ECU-
IG1 NO. 5, ECU-IG1 NO. 448
H-LP RH HI 15 A Right-hand headlight (high beam)49
H-LP LH HI 15 A Left-hand headlight (high beam)50
BIXENON 10 A51
H-LP RH LO 15 A Right-hand headlight (low beam)52
H-LP LH LO 15 A Left-hand headlight (low beam)53
HORN 10 A Horn54
A/F 20 A Multiport fuel injection system/
sequential multiport fuel injection sys-
tem55
S-HORN 7. 5 A S-HORNFuse Ampere Circuit

7194-3. Do-it-yourself maintenance
4
Maintenance and care Light bulbs You may replace the following bulbs by yourself. The difficulty level of
replacement varies depending on the bulb. If necessary bulb replacement
seems difficult to perform, contact your Lexus dealer.
For more information about replacing other light bulbs, contact your Lexus
dealer.
■ Preparing for light bulb replacement
Check the wattage of the light bulb to be replaced. (  P. 817)
■ Removing the engine compartment covers
 P. 6 7 1
■ Turning off the power back door main switch
 P. 5 8
■ Front bulb locations
Vehicles with halogen headlights Headlight high beamHeadlight low beam
Front turn signal light

7224-3. Do-it-yourself maintenance
Replacing light bulbs
■ Headlight high beams
Right side:
Open the cap.
Move the washer fluid filler
opening to allow easy access to
the light bulbs.
Unplug the connector while
depressing the lock release.
Turn the bulb base counterclock-
wise.STEP 1
STEP 2
STEP 3

7244-3. Do-it-yourself maintenance
■ Halogen headlight low beams (if equipped)
Turn the bulb base counterclock-
wise.
Unplug the connector while
depressing the lock release.
Replace the light bulb, and install
the bulb base. Align the 3 tabs on the light bulb
with the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to
check that it is not loose, turn the
headlight low beams on once and
visually confirm that no light is leak-
ing through the mounting.STEP 1
STEP 2
STEP 3
STEP 4

7294-3. Do-it-yourself maintenance
4
Maintenance and care ■ Rear side marker light (left side)
Turn the bulb base counterclock-
wise.
Remove the light bulb.
■ Lights other than the above
If any of the lights listed below ha s burnt out, have it replaced by your
Lexus dealer.
● Discharge headlight low beams (if equipped)
● Daytime running lights
● Parking lights
● Front side marker lights
● Front fog lights
● Side turn signal lights
● Stop lights
● High mounted stoplight
● License plate lightsSTEP 1
STEP 2

7314-3. Do-it-yourself maintenance
4
Maintenance and care CAUTION■
Replacing light bulbs ●
Turn off the lights. Do not attempt to replace the bulb immediately after turning
off the lights.
The bulbs become very hot and may cause burns.●
Do not touch the glass portion of the li ght bulb with bare hands. When it is
unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid
getting moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.●
Fully install light bulbs and any parts used to secure them. Failure to do so may
result in heat damage, fire, or water en tering the headlight unit. This may damage
the headlights or cause condensation to build up on the lens. ●
Vehicles with discharge headlights:
While the low beam headlights are turned
on, and for a short time after they have
been turned off, metal components at the
rear of the headlight assembly will be
extremely hot. To prevent burns, do not
touch these metal components until you
are certain they have cooled down.Metal components

7324-3. Do-it-yourself maintenance
CAUTION■
Discharge headlights (if equipped) ●
Contact your Lexus dealer be fore replacing discharge he adlights (including light
bulbs).●
Do not touch the discharge headlight’s high voltage socket when the headlights
are turned on.
An extremely high voltage of 30000 V wi ll be discharged and could result in
serious injury or death by electric shock.●
Do not attempt to take apart or repair the low beam discharge headlight bulbs,
connectors, power supply circuits, or related components.
Doing so could result in electric shock and serious injury or death.■
To prevent damage or fire
Make sure bulbs are fully seated and locked.