2015 LEXUS LX570 engine

2032-2. Instrument cluster
2
When driving
LX570_OM_OM60L96U_(U) ■ Current fuel consumption
■ Driving range
■ Speedometer Displays the current rate of fuel consumption
Displays the estimated maximum distance that
can be driven with the quantity of fuel remain-
ing • This distance is computed based on your
average fuel consumption. As a result, the
actual distance that can be driven may differ
from that displayed.
• When only a small amount of fuel is added to
the tank, the display may not be updated.
When refueling, turn the “ENGINE START
STOP” switch off. If the vehicle is refueled
without turning the “ENGINE START
STOP” switch off, the display may not be
updated.
Displays the vehicle speed. The speed units (MPH or km/h) can be
selected by pressing the “DISP” switch for
longer than 1 second when the speedometer is
displayed.

2042-2. Instrument cluster
LX570_OM_OM60L96U_(U) ■ Average vehicle speed
■ Front tire angle
■ Turn-by-turn navigation setting screen Displays the average vehicle speed since the
engine was started or the function was reset The function can be reset by pressing the “DISP”
switch for longer than 1 second when the aver-
age vehicle speed is displayed.
Displays the direction of the front tires The tire direction is displayed in 3 stages for
both left and right, in accordance with the angle
of the tire.
The turn-by-turn navigati on can be set to on or
off. The function can be activated or deactivated by
pressing the “DISP” switch for longer than 1 sec-
ond when turn-by-turn navigation setting
screen is displayed.

2052-2. Instrument cluster
2
When driving
LX570_OM_OM60L96U_(U) ■ Tire inflation pressure
■ Display off
A blank screen is displayed Displays inflation pre ssure of each tire. There
is no correlation between the order of the dis-
played values and the tire positions. If the inflation pressure of any tire drops a cer-
tain amount below the tire inflation pressure
value currently memorized in the system, the
displayed values will be highlighted.
It may take a few minutes to display the tire infla-
tion pressure after the “ENGINE START
STOP” switch is turned to IGNITION ON
mode. It may also take a few minutes to display
the tire inflation pressure after inflation pressure
has been adjusted.
If the tire pressure warning light is on or flashing,
a message describing the situation will be dis-
played.

2062-2. Instrument cluster
LX570_OM_OM60L96U_(U) ■
System check display
After turning the “ENGINE START STOP ” switch to IGNITION ON mode,
“LEXUS” is displayed while system operation is checked. When the system check
is complete, the normal screen will return.■
Turn-by-turn navigation
The turn-by-turn navi gation appears only
while route guidance of the navigation sys-
tem is being performed. When a turn
approaches, the distance to the turn and the
turn direction are displayed.
Turn direction
Distance to the next turn
The image shown may differ from the
actual intersection.

2072-2. Instrument cluster
2
When driving
LX570_OM_OM60L96U_(U) ■
Outside temperature display
In the following situations, the correct ou tside temperature may not be displayed, or
the display may take longer than normal to change: ●
When stopped, or driving at low speeds (less than 12 mph [20 km/h]) ●
When the outside temperature has change d suddenly (at the entrance/exit of a
garage, tunnel, etc.)■
When “--” or “E” is displayed
The outside temperature display may be ma lfunctioning. Take your vehicle to your
Lexus dealer. ■
When disconnecting and reconnecting battery terminals
The following information data will be reset: ●
Average fuel consumption after refueling ●
Average fuel consumption ●
Average vehicle speed
CAUTION■
The information displa y at low temperatures
Allow the interior of the vehicle to warm up before using the information display. At
extremely low temperatures, the information display monitor may respond slowly,
and display changes may be delayed.
For example, there is a lag between the driver’s shifting and the new gear number
appearing on the display. This lag could ca use the driver to downshift again, causing
rapid and excessive engine br aking and possibly an accident resulting in death or
serious injury.

208
LX570_OM_OM60L96U_(U) 2-3. Operating the lights and wipers
Headlight switch The headlights can be operated manually or automatically.
Type A
The daytime running
lights turn on.
The side marker,
parking, tail, license
plate and instrument
panel lights turn on.
The headlights and all
lights listed above
(except daytime run-
ning lights) turn on.
The headlights, day-
time running lights
and all lights listed
above turn on and off
automatically.
(When the “ENGINE
START STOP” switch
is in IGNITION ON
mode.)

2092-3. Operating the lights and wipers
2
When driving
LX570_OM_OM60L96U_(U) Type B
The daytime running
lights turn on.
The side marker,
parking, tail, license
plate and instrument
panel lights turn on.
The headlights and all
lights listed above
(except daytime run-
ning lights) turn on.
The headlights, day-
time running lights
and all lights listed
above turn on and off
automatically.
(When the “ENGINE
START STOP” switch
is in IGNITION ON
mode.)

2112-3. Operating the lights and wipers
2
When driving
LX570_OM_OM60L96U_(U) ■
Daytime running light system ●
To make your vehicle more visible to other drivers, the parking lights turn on
automatically (at an increased intensity) whenever the engine is started and the
parking brake is released. Daytime running lights are not designed for use at
night. ●
Compared to turning on the headlights, the daytime running light system offers
greater durability and consumes less electricity, so it can help improve fuel
economy.■
Headlight control sensor
■
Automatic light off system ●
When the headlights are on: The headlight s and tail lights turn off 30 seconds
after a door is opened and closed if the “ENGINE START STOP” switch has
been switched to ACCESSORY or OFF mode. ●
When only the tail lights are on: The tail lights turn off automatically if the
“ENGINE START STOP” switch is sw itched to ACCESSORY or OFF mode
and driver’s door is opened.
To turn the lights on again, turn th e “ENGINE START STOP” switch to IGNITION
ON mode, or turn the light switch off once and then back to the
or
position. The sensor may not function properly if an
object is placed on the sensor, or anything
that blocks the sensor is affixed to the wind-
shield.
Doing so interferes with the sensor detecting
the level of ambient light and may cause the
automatic headlight system to malfunction.