2015 LEXUS LX570 display

2052-2. Instrument cluster
2
When driving
LX570_OM_OM60L96U_(U) ■ Tire inflation pressure
■ Display off
A blank screen is displayed Displays inflation pre ssure of each tire. There
is no correlation between the order of the dis-
played values and the tire positions. If the inflation pressure of any tire drops a cer-
tain amount below the tire inflation pressure
value currently memorized in the system, the
displayed values will be highlighted.
It may take a few minutes to display the tire infla-
tion pressure after the “ENGINE START
STOP” switch is turned to IGNITION ON
mode. It may also take a few minutes to display
the tire inflation pressure after inflation pressure
has been adjusted.
If the tire pressure warning light is on or flashing,
a message describing the situation will be dis-
played.

2062-2. Instrument cluster
LX570_OM_OM60L96U_(U) ■
System check display
After turning the “ENGINE START STOP ” switch to IGNITION ON mode,
“LEXUS” is displayed while system operation is checked. When the system check
is complete, the normal screen will return.■
Turn-by-turn navigation
The turn-by-turn navi gation appears only
while route guidance of the navigation sys-
tem is being performed. When a turn
approaches, the distance to the turn and the
turn direction are displayed.
Turn direction
Distance to the next turn
The image shown may differ from the
actual intersection.

2072-2. Instrument cluster
2
When driving
LX570_OM_OM60L96U_(U) ■
Outside temperature display
In the following situations, the correct ou tside temperature may not be displayed, or
the display may take longer than normal to change: ●
When stopped, or driving at low speeds (less than 12 mph [20 km/h]) ●
When the outside temperature has change d suddenly (at the entrance/exit of a
garage, tunnel, etc.)■
When “--” or “E” is displayed
The outside temperature display may be ma lfunctioning. Take your vehicle to your
Lexus dealer. ■
When disconnecting and reconnecting battery terminals
The following information data will be reset: ●
Average fuel consumption after refueling ●
Average fuel consumption ●
Average vehicle speed
CAUTION■
The information displa y at low temperatures
Allow the interior of the vehicle to warm up before using the information display. At
extremely low temperatures, the information display monitor may respond slowly,
and display changes may be delayed.
For example, there is a lag between the driver’s shifting and the new gear number
appearing on the display. This lag could ca use the driver to downshift again, causing
rapid and excessive engine br aking and possibly an accident resulting in death or
serious injury.

2182-3. Operating the lights and wipers
LX570_OM_OM60L96U_(U) ■
If a warning message of the Auto matic High Beam is displayed...
It may indicate a malfunction in th e system. Contact your Lexus dealer.■
Temporary lowering sensor sensitivity
The sensitivity of the sensor can be temporarily lowered.
To lower the sensitivity, push and hold on the inside rear view mirror for 15 to
20 seconds, and release. The indicator light on the inside rear view mirror will flash
to indicate that the sensitivity has been lowered.
When the “ENGINE START STOP” switch is turned off, the sensitivity will be
returned to its normal level. ■
Customization
The Automatic High Beam can be turned off.
(Customizable features  P. 912)

2342-4. Using other driving systems
LX570_OM_OM60L96U_(U) ■
Cruise control can be set when ●
The shift lever is in the “D” or range “4” or higher of “S” has been selected. ●
Range “4” or higher has been selected by using the paddle shift. (vehicles with
paddle shift switches) ●
Vehicle speed is above approximately 25 mph (40 km/h).■
Accelerating after s etting the vehicle speed●
The vehicle can be accelerated normally. After acceleration, the set speed
resumes. ●
Even without canceling the cruise control, the set speed can be increased by
first accelerating the vehicle to the de sired speed and then pushing the lever
down to set the new speed. ■
Automatic cruise control cancelation
Cruise control will stop maintaining the ve hicle speed in any of the following situa-
tions. ●
Actual vehicle speed falls more than approximately 10 mph (16 km/h) below
the preset vehicle speed.
At this time, the memorized set speed is not retained.●
VSC is activated. ●
Actual vehicle speed is below approximately 25 mph (40 km/h). ●
The switching operation continues for 5 seconds or more after the center dif-
ferential lock switch has been operated.■
If the warning message for the cruise control is shown on the multi-information
display
Press the “ON-OFF” button once to deactiv ate the system, and then press the but-
ton again to reactivate the system.
If the cruise control speed cannot be set or if the cruise control cancels immediately
after being activated, there may be a malfunction in the cruise control system. Have
the vehicle inspected by your Lexus dealer.

2362-4. Using other driving systems
LX570_OM_OM60L96U_(U) Dynamic radar cruise control 
 : If equippedDynamic radar cruise control suppleme nts conventional cruise control
with a vehicle-to-vehicle distance co ntrol. In vehicle-to-vehicle distance
control mode, the vehicle automatica lly accelerates or decelerates in
order to maintain a set followin g distance from vehicles ahead.
Display
Set speed
Indicators
Vehicle-to-vehicle distance
button
Cruise control switch

2382-4. Using other driving systems
LX570_OM_OM60L96U_(U) ■ Adjusting the set speed
To change the set speed, operate the lever until the desired set
speed is displayed.
Increases the speed
Decreases the speed Fine adjustment: Momentarily
move the lever in the desired
direction.
Large adjustment: Hold the
lever in the desired direction.
In the vehicle-to-vehicle distance control mode, the set speed will be
increased or decreased as follows:
• When the set speed is shown in “MPH”
Fine adjustment: By approximately 5 mph (8 km/h) each time the
lever is operated
Large adjustment: By approximately 5 mph (8 km/h) for each 0.75
seconds the lever is held
• When the set speed is shown in “km/h”
Fine adjustment: By approximately 3.1 mph (5 km/h) each time the
lever is operated
Large adjustment: By approximatel y 3.1 mph (5 km/h) for each 0.75
seconds the lever is held
In the constant speed control mode ( 
P. 243), the set speed will be
increased or decreased as follows:
Fine adjustment: By approximately 1 mp h (1.6 km/h) each time the lever
is operated
Large adjustment: The set speed can be increased or decreased contin-
ually until the lever is released

2392-4. Using other driving systems
2
When driving
LX570_OM_OM60L96U_(U) ■ Changing the vehicle-to-vehicle distance
Pressing the button changes the
vehicle-to-vehicle distance as
follows:
Long
Medium
Short The vehicle-to-vehicle distance
is set automatically to long
mode when the “ENGINE
START STOP” switch is turned
to IGNITION ON mode.
If a vehicle is running ahead of
you, the preceding vehicle mark
will also be displayed.
■ Vehicle-to-vehicle distance settings
Select a distance from the tabl e below. Note that the distances
shown correspond to a vehicle sp eed of 50 mph (80 km/h). Vehi-
cle-to-vehicle distance increa ses/decreases in accordance with
vehicle speed. Preceding vehicle mark
Distance options Vehicle-to-vehicle distance
Long Approximately 220 ft. (65 m)
Medium Approximately 130 ft. (40 m)
Short Approximately 100 ft. (30 m)