2015 KIA SORENTO buttons

21ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFET Y WARNINGS
CENTER PANEL
Center Panel Clock Setup*:
Press the H button A to advance the time by one hour
Press the M button B to advance the time by one minute
Navigation System Clock Setup*:
Press the Info/Settings key on the Audio Control Unit Then
press the on-screen Setup button and select the Clock icon
Then use the on-screen buttons to navigate through setup
Press button A to turn the 2nd Row Power Outlet
ON (LED lit)
Press and hold both for more than 5 seconds to switch from 12 to 24 hour formats
QUICK TIPS
Digital Clock
A
B12VMAX
120W12VMAX
120WAUX USB
Aux/USB/iPod® Port
& Power Outlets
•
• The powet outlets are inactive when the ignition is in the OFF position
• The 115 volt AC outlet operates only when vehicle engine is ON
QUICK TIPS
Kia USB Port Video To view a video on your mobile device, snap this QR Code or visit the listed website

Refer to page 2 for more information
QR Code
w w w. KuTechVideos .com/xm13/2015
REMINDER: The Center Panel Digital Clock and Navigation System Clock are not synchronized and may differ slightly
Press the DONE button* on the Navigation screen to ensure changes are saved
QUICK TIPS
*IF EQUIPPED
P
R
N
D
P R
N
DP
R
N
D
SHIFTLOCK RELEASE
activeECOAC
115VPOFF
AC 115V
MAX 150W
(Driver/Front Passenger)
(Button located below Gear Shift) (2nd Row AC Power Outlet)
A

22
REMINDER:
•
Your Automatic Climate Control system may differ from those in the illustrations See your Owner’s Manual for more details
•
When in AUTO mode, Air Flow Mode and Fan Speed do not display on the Climate Control Display
•
Warm air may flow in through vents if Recirculated Air button is not pressed ON (LED lit)
Automatic Climate Control*
Climate Control Auto Function:
1 Press AUTO to select Full Auto Operation
2 Press MODE buttons to control which vents air flows through
3 Press DUAL to select Dual Temperature Control Operation
Defrost Outside Windshield:
1 Set Fan Speed to the highest position 2 Set Temperature to Hot
3 Press the Front Defrost button
Defog Inside Windshield:
1 Set desired Fan Speed
2 Set desired Temperature
3 Press the Front Defrost button
• The A /C Rear button indicator will not illuminate unless the 3rd Row Air Conditioning Fan Speed switch is turned ON (see page 23, 3rd Row Air Conditioning Control)
• Keep inside glass as clean as possible to help reduce window fogging
• Defrost Mode activates A /C and opens Fresh Air Vent
• During Auto Operation the A /C indicator will NOT illuminate The fan speed, air intake, air flow and air conditioning may automatically engage at any time to reach desired temperature and reduce humidity
QUICK TIPS
LCD display
Driver’s temperature control
Automatic Climate Control Mode
Air conditioning ON/OFF
Front windshield defroster button
Recirculated air button
Front blower OFF
A/CA /CR EA R
0 1
2
3
4
A/C
A /C
O
FF
M O
DE D
UAL
REA R
AUTOP
U SH P
U SHFR O NTREA R
CLEAN ONAUTOA UTOD UAL
A/CA /CR EA R
0 1
2
3
4
A/C
A /C
O
FF
M O
DE D
UAL
REA R
AUTOP
U SH P
U SHFR O NTREA R
CLEAN ONAUTOA UTOD UAL
Air Flow Modes
To select Air Flow Modes, rotate the Mode selection knob:
Face-Level
Bi-Level
Floor-Level
Floor/Defrost-Level
Defrost-Level*
Rear window defroster button
3rd row air conditioning ON/OFF* button
Fan speed buttons
Mode selection buttons
Passenger’s temperature control
Dual temperature control mode
SORENTO FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
CENTER PANEL

25ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFET Y WARNINGS *IF EQUIPPED
SEATING
Driver Position Memory System*
To store a seating position into memory, first place the gear shifter into P (Park) while the ignition switch is on Then:
1 Adjust the driver’s seat and outside rearview mirror
2 Press the SET button A on the control panel System will beep once
3 Press one of the memory buttons B within 5 seconds The system will beep twice when memory has been stored
1
SET 2
Seat Warmers/Ventilated Seats*
Press button once for high setting (3 LEDs
lit) Press button twice for medium setting
(2 LEDs lit) Press button a third time for low
setting (1 LED lit) and again to turn OFF
Seat Warmers – Press right side of button
once for high setting (3 LEDs lit) Press
button twice for medium setting (2 LEDs lit)
Press a third time for low setting (1 LED lit)
and again to turn OFF
Ventilated Seats – Press left side of button
once for high setting (3 LEDs lit) Press twice
for medium setting (2 LEDs lit) Press a third
time for low setting (1 LED lit) and again to
t u r n O F F
Seat Warmers only*Seat Warmers/Ventilated Seats*
Warming (Yellow LED)Ventilating (Blue LED)
• With the seat warmer switch in the ON position, the heating system in the seat turns OFF or ON automatically depending on the seat temperature
• System turns OFF when ignition is cycled To turn system ON, press the seat warmer switch
QUICK TIPS
A
B
Hig hM ed iu m Lo wH ig h Med iu m Lo wH ig h Med iu m Lo wH ig hM ed iu m Lo w
Seat Warmers and Ventilated Seats Video To view a video on your mobile device, snap this QR Code or visit the listed website
Refer to page 2 for more information
QR Code
w w w. KuTechVideos .com/xm13/2015
(Located on Center Panel)(Located on Center Panel)
Hig hM ed iu m Lo wH ig h Med iu m Lo wH ig hM ed iu m Lo wH ig h Med iu m Lo w
H ig h Med iu m Lo wH ig h Med iu m Lo wH ig h Med iu m Lo wH ig h Med iu m Lo w

30
•
• You can reprogram a single HomeLink ® button by repeating Step 2
• Erasing programmed buttons will delete all trained transmitters
QUICK TIPS
The Auto-Dimming Rearview Mirror is designed to help
reduce glare from a vehicle’s headlights located in the
rear and also connect up to three electronic transmitters
in one location
To turn automatic dimming ON or OFF, press button F
HomeLink® with Auto-Dimming
Rearview Mirror*
How to Sync Transmitter with HomeLink®*
Erasing programmed buttons:
A HomeLink® button
B HomeLink® button
C Indicator light
D HomeLink® button
E Glare detection sensor
F Automatic dimming ON/OFF
G Compass control button
If programming for the first time, begin with Step 1
(repeating this step will delete all information)
To program non-rolling and rolling code garage door
openers and other devices:
1 Press and hold the left A and center D buttons
simultaneously until the indicator light C begins to
flash (to reprogram buttons, skip this step)
2 Press and hold the desired button A B D and hold
the button on the transmitter while it is approximately
1 to 3 inches away from the mirror The HomeLink®
Indicator light C will flash rapidly once the frequency
signal has been successfully programmed
To finish programming rolling code garage door openers,
complete these steps:
3 Locate the “learn” or “smart ” button on the garage
door’s motor head unit Press and release the button
and complete Step 4 within 30 seconds
4 Firmly press and release the programmed HomeLink®
button up to three times
Press and hold the left A and center D buttons
simultaneously for approximately 20 seconds,
and then release both buttons within 30 seconds
Operating HomeLink®:
Press one of the programmed HomeLink® buttons REMINDER: Mirror indicator light C will illuminate when automatic dimming is ON
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink® Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515 .
ABCDEFG
SORENTO FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES