2015 JEEP RENEGADE lights

•Unstored Messages
This message type is displayed indefinitely or until the
condition that activated the message is cleared. Examples
of this message type are#Turn Signal On#(if a turn signal
is left on) and#Lights On#(if driver leaves the vehicle).
•Unstored Messages Until RUN
These messages deal primarily with the Remote Start
feature. This message type is displayed until the ignition
is in the MAR/RUN state. Examples of this message type
are#Remote Start Aborted - Door Ajar#and#Press Brake
Pedal and Push Button to Start.#
•Five Second Unstored Messages
When the appropriate conditions occur, this type of
message takes control of the main display area for five
seconds and then returns to the previous screen. Ex-
amples of this message type are#Memory System Un-
available - Not in Park#and#Automatic High Beams On.#
Telltales On The EVIC/DID Instrument Cluster
Low Brake Fluid
•What Does It Mean
The light comes on when the brake fluid
level in the reservoir drops below the mini-
mum level, due to a possible loss of liquid
from the circuit.
•What To Do
Restore the brake fluid level, and then
check that the indicator light goes off.
If the light remains on, see an authorized dealer.
184 GETTING TO KNOW YOUR INSTRUMENT PANEL

Electric Park Brake (EPB) Engaged
•What Does It Mean
The light comes on with Electric Park Brake
(EPB) engaged.
•What To Do
Switch off the EPB and check that the
indicator light goes off.
If the light remains on, see an authorized dealer.
Electronic Breakforce Distribution (EBD) Failure
•What Does It Mean
The simultaneous firing ofBRAKE lights
(Red) and(Amber) with the engine
running indicates a failure of the Elec-
tronic Breakforce Distribution (EBD) sys-
tem or that the system is not available. In
this case, with heavy braking, the rear
wheels may lock early and increase the possibility
of skidding.
The dedicated message will appear on the display.
•What To Do
Drive with extreme caution, immediately reach the
nearest authorized dealer for the verification of the
system.
Air Bag
•What Does It Mean
By placing the ignition switch in MAR/
RUN, the indicator light illuminates but
should go out after a few seconds. If the
indicator illuminates, this indicates a failure of the air
bag system.
The dedicated message shows in the display.
For more details, refer to#Occupant Restraint Sys-
tems#in#Safety#for more information.
5
GETTING TO KNOW YOUR INSTRUMENT PANEL 185

LaneSense System
•What Does It Mean
Electronic Vehicle Information Center
(EVIC) — If Equipped
The light comes on in the following ways:
Light illuminated (white):indicates that the system
is active and both of the lane markings have been
detected (the lines of the aisle are gray in color).
Light on as flashing light (amber):indicates that the
vehicle is going to cross over the lane marking.
Light illuminated (green):indicates that both lane
markings have been detected, and the system is
“armed.” The system will provide a torque warning
in the steering wheel if an unintentional lane depar-
ture occurs.
Driver Information Display (DID) — If Equipped
On the vehicles equipped with DID, the light on the
side of the screen will be replaced by an icon in the
upper left area of the display.
These icons are displayed in the same way as vehicles
equipped with EVIC (see as previously described).
Park/Headlight ON Indicator
•What Does It Mean
The light comes on by activating the park-
ing lights or headlights.
This feature allows you to maintain the lights for a
period of 30, 60, or 90 seconds after placing the
ignition in the STOP position.
In some conditions, such as the poor quality of the
fuel, the light may come on only after starting the
engine.
192 GETTING TO KNOW YOUR INSTRUMENT PANEL

Automatic High Beam Lights
•What Does It Mean
The indicator light comes on by activating the
automatic high beam headlights.
Front Fog Lights
•What Does It Mean
The light comes on by activating the fog lights.
Left/Right Turn Signals
•What Does It Mean
The indicator lights flash when the multi-
function lever is moved up/down to show
proper operation of the front and rear turn
signal lights (down (left signal) up (right signal). It is
also used along with the right arrow when the
Hazard Warning flashers are turned on.
Headlights On
•What Does It Mean
The indicator light comes on by turning on the
headlights.
Cruise SET Indicator — If Equipped
•What Does It Mean
This light will turn on when the electronic
speed control is SET.
Symbols Displayed In The EVIC/DID
Oil Pressure Warning Light
•What Does It Mean
This telltale indicates low engine oil pressure.
If the light turns on while driving, stop the vehicle
and shut off the engine as soon as possible. A chime
will sound when this light turns on.
5
GETTING TO KNOW YOUR INSTRUMENT PANEL 193

Light Sensor Failure
•What Does It Mean
The light illuminates in a the light sensor
failure.
•What To Do
Please contact an authorized dealer.
Exterior Light Failure
•What Does It Mean
This light illuminates to indicate a failure of
any of the following lights:
1. Daytime Running Lights (DRL)
2. Parking lights
3. Turn Signals for trailer (if equipped)
4. Trailer lights (if equipped)
5. Position lights
6. Turn Signals
7. Rear Fog light
8. Reverse light
9. Stop lights
10. License Plate lights
The failure could be due to the burning out of the
lamp or protection fuse, or the interruption of the
electrical connection.
•What To Do
Replace the lamp or its fuse. Please contact an autho-
rized dealer.
Keyless Enter-N-Go™ System Failure
•What Does It Mean
The light illuminates in case of failure of
the Keyless Enter-N-Go™.
•What To Do
Please contact an authorized dealer.
198 GETTING TO KNOW YOUR INSTRUMENT PANEL

Enhanced Accident Response System Failure
•What Does It Mean
The light illuminates in case of failure of
the Enhanced Accident Response System.
•What To Do
Please contact an authorized dealer as soon as pos-
sible.
LaneSense System Failure
•What Does It Mean
The light illuminates if there is dirt on the
windshield that could interfere with the
proper operation of the camera.
For vehicles equipped with multifunctional display,
the icon is located on the top right side of the display.
LaneSense System Failure
The light illuminates on if there is a fault in the
LaneSense system.
•What To Do
Clean the windshield, using a soft, clean cloth, being
careful not to scratch it. If the light remains on,
contact an authorized dealer.
Loose Fuel Filler Cap Message Indicator
•What Does It Mean
This light will illuminate to indicate the
fuel filler cap is loose.
•What To Do
Properly close the filler cap.
Automatic Headlights Failure
•What Does It Mean
The light turns on to indicate the failure of
the main beam automatic headlights.
•What To Do
Please contact an authorized dealer as soon as pos-
sible.
5
GETTING TO KNOW YOUR INSTRUMENT PANEL 199

Restore Default Settings
Selecting this item, and you can reset and restore the
default settings.
Vehicle Setup
This menu item allows you to change the settings for the
following:
•Display
•Units of measure
•Clock and Data
•Safety
•Safety and Assistance
•Lights
•Doors and Locks
•Compass (If Equipped)
Vehicles Equipped With Multifunctional Display
Reconfigurable:Menu items#Display#(you can select
only the items#See Phone#and#See Navigation,##Secu-
rity,#and#Safety & Assistance#(only#Volume Alerts#is
selectable) are present.
All other entries are displayed and selected on the
display of the Uconnect® system.
“Display”
By selecting the#Display,#you can access the following
settings:
•Language: allows you to select the language in which
to display the information/warnings.
•See Phone:allows you to view, on the instrument
cluster display, the information relating to Phone
mode displayed on the display of the Uconnect®
system.
5
GETTING TO KNOW YOUR INSTRUMENT PANEL 213

•Buzzer Volume
•Maintenance Brakes (If Equipped): activation of the
procedure to carry out braking system maintenance
•Auto Park Brake (If Equipped): enable/disable auto-
insertion of the Electric Parking Brake
$Lights$
By selecting the item#Lights,#you can make the follow-
ing adjustments:
•Headlight Off Delay: set the delay for headlight shut-
off after engine shutoff
•Lights in the opening: activate the direction indicators
when opening the doors
•Headlight Sensor: adjust the sensitivity of headlight
brightness
•Auto. High Beam: activate/deactivate the automatic
main beam headlights (If Equipped)
•Daytime Lights: activate/deactivate the daytime run-
ning lights
•Cornering lights: activate/deactivate the cornering
lights (If Equipped)
$Doors & Safety$
By selecting the item#Doors & Safety,#you can make the
following adjustments:
•Auto Door Lock: activate/deactivate the automatic
locking of the doors with the vehicle moving
•Auto Unlock On Exit: automatic unlocking of the
doors when exiting the vehicle
•Flash Light with Lock: activate the direction indicators
when closing the doors
216 GETTING TO KNOW YOUR INSTRUMENT PANEL