2015 JEEP CHEROKEE Head lamp

CavityBlade FuseCartridge FuseDescription
F37––Not Used
F38––Not Used
F38–60 Amp Yellow Glow Plugs (Diesel Only) - If
Equipped
F39–40 Amp GreenHVAC Blower Motor
F40–20 Amp BlueTrailer Tow Park Light - If
Equipped
F40–30 Amp PinkHeadlamp Washer Pump - If
Equipped
F41–60 Amp Yellow Body Controller Module (BCM)
- Feed 1
F41–50 Amp RedVoltage Stability Module - Feed
1 - If Equipped with Stop/Start
Engine Option
F42–30 Amp PinkTrailer Tow Electric Brake Mod-
ule
710 MAINTAINING YOUR VEHICLE

CavityBlade FuseCartridge FuseDescription
F6910 Amp Red–Power Transfer Unit Switch
(TSBM) / Active Grill Shutter
(AGS) - If Equipped
F705 Amp Tan–Intelligent Battery Sensor If
Equipped with Stop/Start
Engine Option
F7120 Amp Yellow–HID Headlamp Right if
Equipped with Stop/Start
Engine Option
F7210 Amp Red–Heated Mirrors - If Equipped
F73–20 Amp BlueTrailer Tow Back Up - If
Equipped
F74–30 Amp PinkRear Defroster
F7520 Amp Yellow–Cigar Lighter
F7620 Amp Yellow–Rear Differential Module
(RDM) - If Equipped
7
MAINTAINING YOUR VEHICLE 715

CavityBlade FuseCartridge FuseDescription
F87A20 Amp Yellow–HID Headlamp Left - If
Equipped with Stop/Start En-
gine Option
F8815 Amp Blue–Collision Mitigation Module
(CMM) / Electrochromatic Mir-
ror / Smart Camera Module -
If Equipped
F8910 Amp Red–Headlamp Leveling - If
Equipped
F90––Not Used
F9120 Amp Yellow–Power Outlet Rear
F92––Not Used
F93–40 Amp GreenBrake System Module (BSM) -
Pump Motor
F94–30 Amp PinkElectric Park Brake (EPB) -
Right
7
MAINTAINING YOUR VEHICLE 717

REPLACEMENT BULBS
Interior Bulbs
Bulb Number
Cargo LampTL212–2
Overhead Console LampPLW214–2A
Reading LampWL212–2
Exterior Bulbs
Bulb Number
Low Beam/High Beam (Bi-Halogen) HeadlampsHIR2LL
Low Beam/High Beam (Bi-Xenon) HeadlampsD3S (Serviced at an Authorized Dealer)
Front Park/Daytime Running LampsLED (Serviced at an Authorized Dealer)
Front Turn Signal LampsWY21W or 7440NA
Front Fog LampsH11LL
Front Side Marker Lamps194
Front Fog Lamps (Trailhawk)PSX24W
7
MAINTAINING YOUR VEHICLE 721

Bulb Number
Rear Tail/Turn/Stop LampsLED ( Serviced at an Authorized Dealer)
Center High Mounted Stop Lamp (CHMSL)LED (Serviced at an Authorized Dealer)
Back-Up LampsW16W or 921
License Plate LampW5W
BULB REPLACEMENT
NOTE:Lens fogging can occur under certain atmo-
spheric conditions. This will usually clear as atmospheric
conditions change to allow the condensation to change
back into a vapor. Turning the lamps on will usually
accelerate the clearing process.
Low Beam And High Beam Headlamps
Bi-Xenon High Intensity Discharge (HID)
Headlamps — If Equipped
The headlamps contain a type of high voltage discharge
light source. High voltage can remain in the circuit even
with the headlamp switch off. Because of this, you should
not attempt to service a HID headlamp light source
yourself. If an HID headlamp light source fails, take your
vehicle to an authorized dealer for service.
NOTE:On vehicles equipped with HID headlamps,
when the headlamps are turned on, there is a blue hue to
the lights. This diminishes and becomes more white after
approximately 10 seconds, as the system charges.
722 MAINTAINING YOUR VEHICLE

WARNING!
A transient high voltage occurs at the bulb sockets of
HID headlamps when the headlamp switch is turned
ON. It may cause serious electrical shock or electro-
cution if not serviced properly. See your authorized
dealer for service.
Bi-Halogen Headlamps
1. Remove the 3 hex head screws from the wheel liner.
2. Pull the exterior edge of the liner towards the tire to
gain access to the headlamp bulb cap.
3. Firmly grasp the cap and rotate it counterclockwise to
unlock it.
4. Firmly grasp the bulb and connector assembly and
rotate counterclockwise to remove from the housing.
5. Disconnect the bulb from the electrical connector and
then connect the replacement bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
6. Install the bulb and connector assembly into the
headlamp housing and rotate clockwise to lock it in
place.
7. Install the bulb cap in the headlamp housing and
rotate clockwise to lock it in place.
8. Install the 3 hex head screws into the wheel liner.
7
MAINTAINING YOUR VEHICLE 723

Front Turn Signals And Front Side Marker Lamps
1. Open the hood.
NOTE:Removal of the air cleaner filter housing may be
necessary prior to replacing bulbs in the upper lamp
assembly on the passenger side of the vehicle.
2. Twist the appropriate bulb and socket assembly coun-
terclockwise, and then remove the bulb and socket
assembly from the lamp housing.
3. Pull the bulb out of the socket and insert the replace-
ment bulb.
4. Install the bulb and socket assembly into the housing,
and rotate the socket clockwise to lock it in place.
5. Re-install air cleaner filter housing, if removed.
Front Fog Lamp
1. Remove the 3 hex head screws from the wheel liner.
2. Pull the exterior edge of the liner towards the tire to
gain access to the bulb.
3. Rotate the bulb’s socket counterclockwise, and remove
the bulb and socket assembly from the fog lamp
housing.
4. Pull the bulb out of the socket and insert the replace-
ment bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
5. Install the bulb and socket assembly into the into the
fog lamp housing, and rotate the connector clockwise
to lock it in place.
724 MAINTAINING YOUR VEHICLE

6. Install the 3 hex head screws into the wheel liner.
Front Fog Lamp (Trailhawk)
1. Unlock lower access door in wheel liner.
2. Reach behind the fog lamp housing to access the bulb.
3. Squeeze the two tabs on the side of the bulb socket and
pull straight out from the fog lamp.
4. Disconnect the wire harness from the bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
5. Reconnect the wiring harness to the new bulb and
reinstall by inserting the new bulb straight into the fog
lamp housing until it locks in place.
6. Lock the lower door in the wheel liner.
Bodyside Mounted Back-up Lamp
1. Open the liftgate.
2. Remove the screws that fasten the tail lamp housing to
the vehicle.
3. Grasp the tail lamp and pull firmly rearward to
disengage the lamp from the vehicle.
4. Disconnect the electrical connector.
5. Twist the socket counterclockwise and remove from
housing.
6. Pull the bulb to remove it from the socket.
7. Replace the bulb and install the socket.
7
MAINTAINING YOUR VEHICLE 725