2015 INFINITI Q70 light

12
INFINITI Intelligent Key System

The INFINITI Intelligent Key system allows you to lock
or unlock your vehicle, open your trunk and start
the engine. It is important to make sure the Intelligent
Key is with you (that is, in your pocket or purse).

The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.


To lock the vehicle, push either door handle request switch
1
once or press the
button
2 on the key fob.

To unlock the vehicle, perform one of the following procedures:
•
Push either door handle request switch

1 once;
the corresponding
door will unlock. Push the door handle request switch 1 again within

1 minute; all other doors will unlock, or
•
Press the

button
3 on the key fob to unlock the driver’s side door.

Press the
button again; all other doors will unlock.

To open the trunk, press the HOLD button
4 for more than 1 second.


The Intelligent Key can also be used to activate the panic alarm by pres\
sing
and holding the
button
5 for more than 1 second. Once activated, the

panic alarm and headlights will stay on for a period of time.
INTELLIGENT KEY BATTERY DISCHARGE


If the battery of the Intelligent Key is discharged
or environmental conditions interfere with the
Intelligent Key operation, start the engine according
to the following procedure:
1. Move the shift lever to the P (PARK) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key,
and a chime will sound.
4.
Within 10 seconds after the chime sounds, push the ignition switch while depressing the
brake pedal and the engine will start.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and
the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
1
2
3
4
5
first drive features
1727653‎_15b_Infiniti_Q70_QRG_100814.indd 1210/8/14 11:36 AM

14
first drive features
Automatic Drive Positioner
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner

1 memory.

Follow this procedure to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Push the ignition switch to the ON position.
•
Adjust the driver’s seat, steering column and outside mirrors to the \
desired positions using

the adjusting switches for each feature.
•
Push the SET switch and within 5 seconds push the memory switch (1
or 2) for at least
1 second.
•
The indicator light on the memory switch you select will illuminate for \
approximately

5 seconds.
• The driver’s seat, steering column and outside mirror positions are n\
ow set to
your preferences.

These memorized positions can also be linked to your INFINITI Intelligen\
t Key.

To link a memorized position to your INFINITI Intelligent Key, press the\
unlock button on the
key fob after completing the previous step.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the control
switch

1 right or left.

Adjust each mirror to the desired position using
the switch

2 .

To fold the outside rearview mirrors, push the switch
3 to the
position. To unfold the outside rearview
mirrors, push the switch
3 to the
position.
REVERSE TILT-DOWN FEATURE

When backing up the vehicle, the right or left outside mirror can be sel\
ected to automatically
turn downward.
1. Push the ignition switch to the ON position.
2. Move the shift lever to the R (REVERSE) position.
3. Choose the right or left outside mirror by operating the outside mirr\
or control switch

1 .
4. The outside mirror surface moves downward.

When one of the following conditions has occurred, the outside mirror su\
rface will return to
its original position.
• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center or neutral positi\
on.
• The ignition switch is pushed to the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
1
1
23
1727653‎_15b_Infiniti_Q70_QRG_100814.indd 1410/8/14 11:36 AM

15
Starting/Stopping the Engine
It is important to make sure the INFINITI Intelligent
Key is with you (that is, in your pocket or purse).

Depress the brake pedal.

Press the ignition switch START/STOP button to start
the engine.
TURNING THE ENGINE OFF

Move the shift lever to the P (PARK) position and
apply the parking brake.

Press the ignition switch START/STOP button to turn the engine off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Headlight Control Switch
HEADLIGHT CONTROL

Turn the headlight control switch to the position
1 to turn on the front parking, side marker, tail, license

plate and instrument panel lights. Turn the switch to
the
position
2 to turn on the headlights.
AUTOLIGHT SYSTEM

The autolight system will automatically turn the headlights on when it i\
s dark and off when it is
light. The system will keep the headlights on for a period of time after\
you turn the ignition off
and all doors are closed.

To activate the autolight system, turn the headlight control switch to t\
he AUTO position
3
then push the ignition switch to the ON position. To deactivate the autolight system, turn the
headlight control switch to the OFF,
position
1 or
position
2 .
HIGH BEAM SELECT

Push the headlight control switch forward
4 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel.
Pull the headlight switch back to the original
position to select the low beam. The blue indicator
light extinguishes.

Pull and release the headlight control switch
5 to

flash the headlight high beams on and off.
3
1
2
45
1727653‎_15b_Infiniti_Q70_QRG_100814.indd 1510/8/14 11:37 AM

16
first drive features
FOG LIGHT SWITCH

The headlights must be on and the low beams

selected for the fog lights to operate.

Turn the switch (inside collar) to the position
6
to turn the fog lights on.

Turn the switch (inside collar)
to the OFF position to

turn the fog lights off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
6
Windshield Wiper and Washer Switch
Move the lever to one of the following positions to
operate the windshield wipers:

1 Mist (MIST) - One sweep operation of the wipers.

2
Auto
(AUTO) - Operates the rain-sensing wipers
intermittently. To increase or decrease wiper
sensitivity, twist the control ring
3 .

4
Low
(LO) - Wipers operate at a continuous
low-speed.

5
High
(HI) - Wipers operate at a continuous
high-speed.

6
Pull the lever toward you to activate the washer.

The wipers will operate several times.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service position in order to replac\
e the wiper blades. To move
the wiper blades to the service position, follow this procedure:

When the ignition switch is in the ON position, lift the windshield wiper and washer lever up to
the MIST position
1 two times in less than 0.5 seconds. The windshield wipers will move to \
the
service position automatically, and the wiper blades can now be replaced\
.
To move the wiper blades back to the original position:

Lift the windshield wiper and washer lever up for more than 1 second or \
push the lever down to
operate at any wiper speed.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
MIST
OFF
AUTO
LO
HI
2
4
5
13
6
1727653‎_15b_Infiniti_Q70_QRG_100814.indd 1610/8/14 11:37 AM

18
first drive features
7 FAN SPEED CONTROL BUTTONS

Press the left button to decrease the fan speed or press the right
button to

increase the fan speed.
8 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS

Press the defroster button
to turn the system on. The A/C automatically turns

on when the defroster mode is selected. This feature removes humidity fr\
om the air.

To defrost the front and side windows, set the temperature controls
3 and fan speed

controls 7 to their maximum settings.
9 DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS

Push the rear window defroster switch
to turn the system on or off.
This function automatically turns off after approximately 15 minutes.
10 INTAKE AIR CONTROL BUTTON

Press the intake air control button to recirculate interior air inside the vehicle.
The
indicator light on the button will illuminate. This system is used to a\
void certain
outside odors and to help adjust the inside vehicle temperature more eff\
ectively.

The air recirculation mode cannot be activated when the climate control \
system is in the
front defroster mode

or front defroster and foot vent mode
.

Press the intake air control button again to change the air circulation from the
intake air to the outside air. The
indicator light on the button will extinguish.
11 OFF BUTTON

Press the OFF button to turn the climate control system off.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (secti\
on 4)” of your
Owner’s Manual.
1727653‎_15b_Infiniti_Q70_QRG_100814.indd 1810/8/14 11:37 AM

20
first drive features
Conventional (Fixed Speed) Cruise Control
The cruise control system enables you to set a
constant cruising speed once the vehicle has reached
25 mph (40 km/h).

The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.

To activate the cruise control, push the ON/OFF
switch
1 . The
CRUISE
indicator light in the

instrument panel will illuminate.

To set a cruising speed, accelerate the vehicle to the desired speed, pu\
sh the COAST/SET
switch

2 and release. The
SET
indicator light
in the instrument panel will

illuminate. Take your foot off the accelerator pedal. Your vehicle will \
maintain the set speed.

To reset at a faster cruising speed, push and hold the ACCEL/RES switch
3 . When the
vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch
2. Release the
switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
4 .

To turn off cruise control, push the ON/OFF switch
1 . Both the CRUISE indicator light and
the SET indicator light in the instrument panel will extinguish.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
1
3
2
4
USB (Universal Serial Bus) Connection Port/iPod® Interface

The USB port
1 is located in the center console under
the arm rest.

When a compatible USB memory device or iPod® is

plugged into the USB port, compatible audio and
video files stored on the device can be played
through the vehicle’s audio system and front display.
For more information, refer to the “Monitor, climate, audio, phone
and voice recognition systems (section 4)” of your Owner’s Manual.1
1727653‎_15b_Infiniti_Q70_QRG_100814.indd 2010/8/14 11:37 AM

21
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button
1 for less

than 1.5 seconds. The CRUISE indicator light
2
will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch
3 and release
it. Intelligent Cruise Control will be set to the
desired speed.

Press the distance button
4 repeatedly to change
the set distance between long, middle and short.

When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed indicator
lights will illuminate
5 in set mode.

When a vehicle is detected ahead of you in the lane, the vehicle ahead
detection, set distance and set vehicle speed indicator lights will
illuminate

6 in set mode.

To reset at a faster cruising speed, push and hold the ACCEL/RES switch 7 . When the
vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch
3 . Release the
switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
8 or tap the brake pedal. The set
vehicle speed indicator 5 will extinguish.

To turn off Intelligent Cruise Control, press the CRUISE ON/OFF button
1 . The CRUISE

indicator light 2 in the instrument panel will extinguish.
To set conventional (fixed speed) cruise control mode:

While Intelligent Cruise Control is off, press the CRUISE ON/OFF
button
1 and hold it
down for more than 1.5 seconds. The CRUISE
indicator light will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control should be set to the desired speed.
To switch between the two cruise control modes:

When one of the two cruise modes is in use, you must turn the system off\
and then turn it on
again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
25
6
87
3
1
4
1727653‎_15b_Infiniti_Q70_QRG_100814.indd 2110/8/14 11:37 AM

26
system guide
Navigation System (if so equipped)
1 Touch-screen display
2 DEST (Destination)– Press to enter a destination.
3 INFO
(Information) – Press to display the vehicle, traffic (if so equip\
ped), weather (if so
equipped) or Voice Recognition information.
4 SETTING – Press to access the system settings.
5 Multi-Function Controller

• ENTER – Press the ENTER button to select the highlighted item on the screen.
• Center Dial – Turn the dial to highlight an item on the screen, adjus\
t a setting or adjust
the map scale.
• Slide the controller (push upward/downward/leftward/rightward) to sele\
ct an item on the
screen, to adjust a setting or scroll the map in eight directions.
6 ROUTE – Press to access guidance control functions, such as guidance cance\
llation, route

priority or waypoint setting on the route.
7 MAP – Press to display the map. While following a programed route, press\
multiple times to
change the type of route information.
23
5
4
98
1110
76
1
1727653‎_15b_Infiniti_Q70_QRG_100814.indd 2610/8/14 11:38 AM