2015 Hyundai Grand i10 maintenance

Maintenance
30
7
AIR CLEANER
If the stroke is more or less than speci-
fied, we recommend that the system be
serviced by an authorized HYUNDAI
dealer.
Stroke : 6~8 clicks at a force of 20kg (44lbs, 196N). Filter replacement
It must be replaced when necessary, and should not be cleaned and reused.
1. Remove the intake hose clamp.
2. Loosen the air cleaner cover attachingclips and open the cover.
OBA073025
OBA073026

731
Maintenance
3. Replace the air cleaner filter.
4. Reassemble in the reverse order ofremoval. Replace the filter according to the
Maintenance Schedule.
If the vehicle is operated in extremely
dusty or sandy areas, replace the ele-ment more often than the usual recom-
mended intervals. (Refer to“Maintenance under severe usage condi-tions” in this chapter.)
CAUTION
Do not drive with the air cleaner removed; this will result in exces-
sive engine wear.
When removing the air cleaner fil- ter, be careful that dust or dirtdoes not enter the air intake, or
damage may result.
We recommend that you use parts for replacement from anauthorized HYUNDAI dealer. Useof improper parts could damage
the air flow sensor or turbo charg-er.
OBA073027

Maintenance
32
7
CLIMATE CONTROL AIR FILTER (IF EQUIPPED)
Filter inspection The climate control air filter should be replaced according to the Maintenance
Schedule. If the vehicle is operated in
severely air-polluted cities or on dusty
rough roads for a long period, it shouldbe inspected more frequently and
replaced earlier. When you replace the
climate control air filter, replace it per-
forming the following procedure, and be
careful to avoid damaging other compo-
nents.
Filter replacement
1. With the glove box opened, push inboth sides of the glove box as shown.
This will ensure that the glove boxstopper pins will get released from its
holding location allowing the glove boxto hang. 2. Remove the climate control air filter
cover.
OBA073032
OBA073032R
■Left-hand drive
■Right-hand driveOBA073029
OBA073029R
■ Left-hand drive
■Right-hand drive

733
Maintenance
3. Pull out the air filter4. Replace the climate control air filter.
5. Reassemble in the reverse order of
disassembly.
✽✽ NOTICE
When replacing the climate control air
filter install it properly. Otherwise, the
system may produce noise and the effec-
tiveness of the filter may be reduced.
OBA073030
OBA073030R-1
■ Left-hand drive
■Right-hand driveOBA073031

Maintenance
34
7
WIPER BLADES
Blade inspection
✽✽ NOTICE
Commercial hot waxes applied by auto-
matic car washes have been known to
make the windshield difficult to clean.
Contamination of either the windshield or
the wiper blades with foreign matter can
reduce the effectiveness of the wind-
shield wipers. Common sources of con-
tamination are insects, tree sap, and hot
wax treatments used by some commer-
cial car washes. If the blades are not wip-
ing properly, clean both the window and
the blades with a good cleaner or mild
detergent, and rinse thoroughly with
clean water. Blade replacement When the wipers no longer clean ade-
quately, the blades may be worn or
cracked, and require replacement.
1JBA5122CAUTION
To prevent damage to the wiper
blades, do not use gasoline, kerosene, paint thinner, or other
solvents on or near them.
CAUTION
To prevent damage to the wiperarms or other components, do not
attempt to move the wipers manual-ly.
CAUTION
The use of a non-specified wiperblade could result in wiper malfunc- tion and failure.

735
Maintenance
Front windshield wiper blade
Type A
1. Raise the wiper arm and rotate thewiper blade assembly to expose the
plastic locking clip.
2. Compress the clip (1) and slide theblade assembly downward (2).
3. Lift it off the arm.
4. Install a blade assembly in the reverse order of removal.
5. Return the wiper arm on the wind- shield. Type B
1. Raise the wiper arm.
1LDA5023
CAUTION
Do not allow the wiper arm to fall
against the windshield, since it may chip or crack the windshield.
1JBA7037
1JBA7038
OHM078059
CAUTION
Do not allow the wiper arm to fall
against the windshield, since it may chip or crack the windshield.

Maintenance
36
7
2. Lift up the wiper blade clip (1). Then
pull down the blade assembly (2) and
remove it. 3. Install a new blade assembly in the
reverse order of removal.
4. Return the wiper arm on the wind- shield.Rear window wiper blade
(if equipped)
1. Raise the wiper arm and pull out the wiper blade assembly.
2. Slightly rotate the wiper blade assem- bly (1) and pull it out.
OHM078060OHM078061OPA077017

737
Maintenance
3. Install a new blade assembly by insert-ing the center part into the slot on the
wiper arm until it clicks into place.
4. Make sure the blade assembly is installed firmly by trying to pull it slight-
ly.
To prevent damage to the wiper arms or
other components, we recommend that
the wiper blade be replaced by an
authorized HYUNDAI dealer.
OPA077018