Maintenance
70
7
Headlight, position light, turn sig-
nal light, and front fog light bulbreplacement
(1) Headlight (Low/High)
(2) Parking(Position) light
(3) Front turn signal light
(4) Front fog light / Daytime running light
(if equipped)
✽✽NOTICE
If the headlight aiming adjustment is
necessary after the headlight assembly is
reinstalled, consult an authorized
HYUNDAI dealer.
OBA073018OHD076046
WARNING - Halogen bulbs
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
Always handle them carefully, and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact with liquids. Never touchthe glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated onlywhen installed in a headlight.
(Continued)
(Continued)
If a bulb becomes damaged orcracked, replace it immediately
and carefully dispose of it.
Wear eye protection when chang- ing a bulb. Allow the bulb to cool
down before handling it.
771
Maintenance
Headlight (Low/High)
1. Open the hood.
2. Remove the headlight bulb cover byturning it counterclockwise.
3. Disconnect the headlight bulb socket- connector.
4. Unsnap the headlight bulb retaining wire by depressing the end and push-
ing it upward.
5. Remove the bulb from the headlight assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
7. Connect the headlight bulb socket con- nector.
8. Install the headlight bulb cover by turn- ing it clockwise.
Turn signal light
1. Remove the turn signal light bulb coverby turning it counterclockwise.
2. Remove the socket from the assembly by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until it locks into
place.
4. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
Parking(Position) light
1. Remove the socket from the assemblyby pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
OBA073047R
Headlight
Parking(Position) light
Turn signal light
BULB WATTAGE
Specifications & Consumer information
2
8
DIMENSIONS
* : If equipped
*
1
: 4 Door
* 2
: 5 Door Light Bulb Wattage
Front Headlights (High/Low) 60/55
Front turn signal light 21
Parking(Position) light 5
Front fog light* 35
Side repeater light* 5
Daytime running light* 21
Rear Stop and tail light 21/5
Back-up light 16
Rear turn signal light 21
Rear fog light* 21
High mounted stop light* 5
Interior License plate light 5
Room lamp 8
Luggage room lamp* 8
Glove box lamp* 5
ENGINE
Item 1.0 Kappa 1.2 Kappa
Displacement cc (cu. in) 997 (60.8) 1,248 (76.2)
Bore x Stroke mm (in.)71.0x84.0
(2.8x3.3) 71.0x78.8
(2.8x3.1)
Firing order 1-2-3 1-3-2-4
No. of cylinders 3 4
Item mm (in)
Overall length 3995 (157.3)* 1
/3765 (148.2)* 2
Overall width 1660 (65.4)* 1
*2
Overall height 1520 (59.8)* 1
*2
Front tread 1479 (58.2) Rear tread 1493 (58.8)
Wheelbase 2425 (95.5)* 1
*2
