2015 FORD F750 tire type

Irregular Wear:If irregular wear is present, check the axle alignment,
tire pressure, wheel balancing, shock and suspension component
condition, and wheel bearing end play.
This condition not only shortens tire life, but also adversely affects the
handling of your vehicle, which is dangerous.
Rotating tires from one wheel position to another is an often-used way to
even out many types of irregular wear or to avoid it altogether. Some of
the more effective tire rotation programs are:
•You can rotate steer tires that have developed some type of irregular
wear pattern to drive axles if using rib tires on all wheel positions.
Applying steer tires to a drive position often cleans them. You can
move them back to the steer axles or run out to re-tread stage on the
rear axle.
•Another rotation possibility for fleets with rib tires in all wheel
positions is to break in the new steer tires in the drive axle positions,
then move them to steer axles. This wears away tread rubber
relatively quickly in the early life of a tire when it is most likely to
develop an unusual wear pattern.
•You can place drive axle tires on the other end of the same axle to
reverse the direction of rotation. This is often helpful if a heel and
toe or alternate lug wear pattern has developed.
You can help minimize irregular wear by:
•Using the right inflation pressure for the load being carried.
•Maintaining proper front wheel alignment, especially toe-in, to
specifications.
•Maintaining proper tire and wheel balance.
•Maintaining shock absorbers and suspension components.
Use of Tire Chains
See the chain manufacturer’s recommendation for correct tire chain
usage, installation and removal.
WHEELS
General Information
Note:Remember to replace the wheel air valves when replacing the road
tires at the end of their useful lives.
Inspect, lubricate and adjust wheel bearings at regular intervals. This is
especially important if operating in deep sand, mud or water. See the
Capacities and Specificationschapter.
Mount wheel balance weights on the dome-side of the wheel only. Failure
to do so may result in loss of wheel weight or damage to brakes or
wheels.
Wheels and Tires249
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

Oil-lubricated Front Wheel Bearings
During normal vehicle duty cycle, the lubricant and air inside the
hub/wheel cavity expands and, if not vented, causes pressure build-up
that could cause accelerated seal wear. You can use two venting methods
to prevent pressure build-up:
•A slit or small hole in the rubber check vent
•The window.
Over a period, if not routinely cleaned, a slight film of oil can collect dirt
around the rubber fill plug and face, which could appear to be a leak.
Routine cleaning helps make sure that you can easily observe the
lubricant level through the window as intended. In situations where the
window is clean on the outside but discolored on the inside, you can
check the lubricant level by inserting a finger through the rubber check
vent hole.
The specified lubricant level for a window-type hubcap is from the
minimum line to five–sixteenth inch (8 millimeters) above the minimum
line. If the lubricant level should suddenly drop dramatically below the
minimum level, see theWorkshop Manualfor diagnostic procedure.
Installation, Tightening and Alignment
Make sure the threads on the studs and nuts are clean to permit correct
torque when installing wheels. The mounting surfaces of rims, wheels,
spacer rings and clamps must be free of dirt, rust, lubricants or damage.
Use a wire brush to clean the mounting contact surfaces. Do not use
lubricant on threads.
After properly tightening the rim or wheel, check it for proper alignment.
Rotate the wheel with a piece of chalk attached to a steady, firm surface,
and placed to just barely clear the outside surface of the tire bead seat;
this procedure points out the high spot. A high spot does not necessarily
indicate unevenly tightened lug nuts, but may be the result of a bent
wheel.
Use the following installation procedure:
1. Slide inner rear or front tire and wheel in position over studs and push
it back as far as possible. Use care so you do not damage the threads on
the studs.
250Wheels and Tires
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

Note:Make sure the tire valve stem clears the brake caliper when
installing the tire and rim assembly on disc-brake equipped axles. The
use of a tire manufacturer’s stem forming tool is the only acceptable
method of obtaining clearance when necessary.
Proper Torque
It is important to tighten and maintain wheel and rim mounting nuts to
the proper torque. Loose nuts or over-tightened nuts can lead to
premature wear and possible failure of the wheel or mounting hardware.
Changing Wheel Types
WARNING:Use only the same type and style wheels and
mounting hardware to replace original parts. Failure to do so may
result in an assembly that looks fine, but does not fit together properly.
This could possibly cause wheel or fastener failures which could result
in property damage, personal injury or death.
Note:Do not attempt to mix stud-piloted wheels or fasteners with
hub-piloted wheels or fasteners.
Note:Do not change from aluminum wheels to steel wheels or
vice-versa without changing the mounting hardware required or, with
flange nut mounting systems, changing the hub and stud assembly.
Consult your dealer or wheel or rim distributor before attempting any
wheel or fastener changes.
TECHNICAL SPECIFICATIONS
Wheel Lug Nut Torque Specifications
Note:Do not use lubrication on dry threads. Where excessive corrosion
exists, you can apply a light coat of lubricant on the first three threads
of the stud bolt. Keep lubricant away from the:
•Hex nut and rim clamp contact surfaces.
•Cap nut ball face and ball seat on the disc wheel.
•Flange nut washer surface and flat on the disc wheel.
Size Nut MountingTorque
ft-lb N•m
22 mm Flange 450–500 610–678
Wheels and Tires253
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

Every Oil Change
ClutchLubricate the clutch release cross shaft and all
linkages.
Check the clutch fluid level.
Fuel SystemDrain the accumulated water or sediment from
the fuel tank(s).
Steering SystemLubricate the steering shaft(s), U-joints and
splines if equipped with grease fittings.
Lubricate the front axle spindle pins.
Lubricate the steering linkage when equipped
with grease fittings.
Lubricate the power steering gear output shaft.
*Make coolant protection checks just before the onset of freezing
weather, where applicable. If coolant is dirty or rusty in appearance,
drain the system, flush and refill the system with the prescribed solution
of cooling system fluid and distilled water. Use only permanent type
coolant that meets specifications as listed in your engine operator’s
manual. See the engine manufacturer’s operating guide for supplemental
corrosion inhibitor specifications.
Periodic Component and System Checks
The following are vehicle checks that should be made periodically either
by the owner or a qualified technician. Bring any deficiencies to the
attention of an authorized dealer or another qualified service outlet as
soon as possible to obtain advice about the need for service or
replacement.
Frequency Recommended Action
At every engine start up. Check ABS lamp operation.
After first 500 and 1000 miles (800
and 1600 km), then every 500 and
1000 mile (800 and 1600 km)
interval after tire removal or
replacement.Tighten the wheel mounting nuts
to the specified torque. See
Technical specificationsin the
Wheels and Tireschapter.
At least twice annually. Clean body and door drain holes.
As required. Clean windshield wiper blades.
Scheduled Maintenance343
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)