2015 FORD F650 wheel bolts

Front brakes
HosesInspect for cracked, worn or frayed hoses.
Verify all couplings are secure.
Brake chambersVerify:
•There are no cracks or dents
•They are securely mounted.
Slack adjustersInspect for broken, loose or missing parts.
Note:The angle between the push rod and
adjuster arm should be approximately 90
degrees when the brakes are applied. When
pulled by hand, the push rod should not move
more than approximately 1 inch (2.5
centimeters).
DrumsVerify:
•There are no cracks, dents, holes, and no
loose or missing bolts
•The brake linings are not worn, dangerously
thin or contaminated by lubricant.
Front wheels
RimsInspect for damaged or bent rims. They should
not have welding repairs, and there should be no
rust trails, which indicate it is loose on the wheel.
Lug nutsVerify all lug nuts are present and not loose (look
for rust trails around the lug nuts). There should
be no cracks radiating from the lug bolt holes or
distortion of the bolt holes.
Hub oil sealsInspect wheel hub oil seal for leaks and, if sight
glass if present, verify the oil level is adequate.
Oil-lubricated
front wheel
bearingsInspect for proper lubrication level if the hubcap
has a transparent window. If the hubcap does not
have a transparent window, remove the rubber
fill-plug and inspect for proper level.
Fuel area
Fuel tank(s)Verify:
•Tank(s) and cap(s) are secure
•There is no damage to the tank(s).
LeaksInspect for leaks from the tank(s).
18Vehicle Inspection Guide
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

Rear of vehicle
Lights and
reflectorsVerify:
•All exterior lights illuminate and are clean
•Reflectors are clean, unbroken and of proper
color (red on rear, amber elsewhere)
•Running lights are clean and unbroken.
Note:Inspect rear running lights separately from
signal, flasher and brake lights.
Tractor-coupling system
Mounting boltsInspect for loose or missing mounting brackets,
clamps, bolts or nuts. Verify solid attachment of
both fifth wheel and the slide mounting.
PlatformInspect for cracks or breaks in the platform
structure.
Safety latchVerify engagement of the safety latch.
Release armVerify:
•The safety latch is in the engaged position
•Any safety latch is in place.
Kingpin and
apronVerify:
•The kingpin is not bent or worn
•The apron lies flat on the fifth-wheel skid plate
•The visible part of the apron is not bent, worn,
cracked or broken.
Rear suspension
SpringsInspect for broken or shifted leaves or leaves that
are in contact with (or nearly contacting) a tire,
rim, brake drum, frame or body component.
Inspect for missing or broken leaves in the leaf
spring.
Spring mountsInspect for any:
•Cracked or broken spring hangers
•Broken, missing or loose bolts
•Missing or damaged bushings
•Broken, loose or missing axle mounting parts.
20Vehicle Inspection Guide
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

Rear suspension
Torsion arm and
shock absorbersVerify torsion arm is not cracked, broken or
missing.
Inspect the shock absorber for cracks or leaks.
There should be no missing or broken mounting
bolts or worn bushings.
Rear brakes
Hoses•Inspect for cracked, worn or frayed hoses.
Verify all couplings are secure.
Brake chambersVerify:
•There are no cracks or dents
•They are securely mounted.
Slack adjusterInspect for broken, loose or missing parts.
Note:The angle between the push rod and
adjuster arm should be approximately 90 degrees
when the brakes are applied. When pulled by
hand, the push rod should not move more than
approximately 1 inch (2.5 centimeters).
DrumVerify:
•There are no cracks, dents, holes and no loose
or missing bolts
•The brake linings are not worn, dangerously
thin or contaminated by lubricant.
Rear wheels
SpacersVerify:
•Even separation of dual wheels
•The tires are not touching one another.
RimsInspect for damaged or bent rims. Rims should
not have welding repairs, and no rust trails,
which indicate it is loose on the wheel.
Lug nutsVerify all lug nuts are present and not loose (look
for rust trails around the lug nuts). There should
be no cracks radiating from the lug bolt holes or
distortion of the bolt holes.
Vehicle Inspection Guide21
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

Towing the Vehicle with the Front Wheels Suspended
Note:To avoid transmission damage, do not tow your vehicle even a
short distance without suspending rear wheels or removing the axle
shafts or driveshaft.
Note:When towing a vehicle equipped with a tandem axle from the
front, raise the forward rear axle so it can clear the road surface and
secure it to the frame with chains or U-bolts, allowing only the rear rear
axle to contact the road surface. Remove axle shafts from the rear rear
axle assembly. Cover the wheel hub ends to prevent loss of axle lubricant
and entrance of contaminants. Use extreme care in securing the chains
or U-bolts to avoid possible damage to the brake lines, hoses or other
components.
When it is necessary to tow a vehicle with the front wheels suspended,
take extra precautions to avoid transmission or differential damage:
•Remove the axle shafts from the axle assembly to prevent the wheels
from driving the differential and the transmission.
•Cover the wheel hub ends to prevent loss of axle lubricant and
entrance of other contaminants. If you do not remove the axle shafts,
removal of the driveshaft is required.
Towing the Vehicle with the Rear Wheels Suspended
Note:To avoid damage to the cab roof or air deflector when towing your
vehicle backward (rear wheels suspended), remove the air deflector.
Whenever possible, it is preferable to tow a disabled vehicle from the
rear by raising the rear of the chassis. When towing a vehicle with the
rear of the chassis suspended, you must lock the front wheels in the
straight-ahead position.
Vehicles equipped with a manual transmission must have at least 1.0 pint
(0.5 liter) of transmission fluid drained from the case. This prevents the
transmission fluid from entering the clutch housing and saturating the
clutch discs. Make sure to replace the transmission fluid before returning
your vehicle to service.
Towing Vehicles Equipped with a Driver-controlled Differential
Lock
Note:If you have to tow your vehicle to a service facility with the drive
axle wheels on the ground, it is necessary to remove the axle shafts
before towing your vehicle.
172Towing
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

Climate Control System
Have the air conditioning system checked each spring. The refrigerant
charge, cleanliness of the condenser-evaporator cores and belt condition
are essential to system performance.
When the air conditioning system is being used daily, remove the fresh
air filter (if equipped) once each season and check for things such as
dirt and lint. Replace the filter if necessary. Vehicles operating in
unusually dusty conditions may require more frequent filter inspection
and replacement.
Front Axle
Maintaining the front axle alignment to specifications is very important.
A qualified technician should check and maintain the alignment. Regular
inspections should include:
•Toe-in inspection and adjustment (if necessary), particularly with
radial tires.
•Checking for proper tightness of axle mounting U-bolt nuts, attaching
or mounting bolts and nuts.
•Checking the axle for damage, binding, worn parts and adequate
lubrication..
•Checking the kingpins for excessive wear. Also, perform this check
during other scheduled maintenance (such as tire rotation or service,
wheel bearing service and alignment). See the workshop manual for
proper procedures.
Toe-in
It is essential to maintain correct toe-in and tire pressure for optimum
tire wear.
Inspecting steer axle tires in the first 3000–10000 service miles
(5000–16000 service kilometers) generally shows if tires are wearing
normally.
Rapid outside shoulder wear on both tires indicates too much toe-in.
Rapid inside shoulder wear on both tires indicates too much toe-out.
In P&D-type service, there can be a left-to-right steer tire tread life
differential up to 40% depending on routes and other variables.
Follow the tire manufacturer’s recommended cold inflation pressure for
the tire size, load range (ply rating) and steer axle loading typical for
their operation (each steer axle tire equals
12steer axle loading).
Maintenance199
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

provided by the service manual. Hydraulic brake systems are
power-assisted. There is a great reduction in braking capabilities
without engine assist.
•Proper fluid level. The level should be at the bottom edge of the ring
on each reservoir fill port. Do not fill the master cylinder to the top of
the reservoir. If fluid level requires attention to maintain a proper
master cylinder level, this is an indication of either severe operation
(pad wear) or fluid leakage. A more frequent and thorough brake
inspection is required.
•Brake lines, hoses and fittings. Repair or replace brake line tubes,
hoses or fittings as required. Inspect these components every
4000 miles (6000 kilometers):
•Lines for kinks, dents, corrosion or rupture.
•Hoses for abrasions, kinks, soft spots or rupture, collapse, cracks,
twists or loose frame supports. When replacing a hose, be sure
there is adequate clearance to the hose to avoid an abrasion to the
new hose.
•All connections for leaks.
Driveline Parking Brake
WARNING:Use wheel chocks and exercise caution when
inspecting under the vehicle. A vehicle roll-away could result in
property damage, personal injury or death.
A qualified technician should adjust the parking brake and keep to the
instructions in the service manual.
Steering System
WARNING:Failure to maintain the steering system in proper
condition can cause reduced steering ability resulting in property
damage, personal injury or death.
Note:Have any steering problems immediately corrected by a qualified
service technician.
Ask your service technician to examine the steering mechanism. Only
minor adjustments may be necessary. Regular inspections should include:
•Checking the tie rod, drag link end clamp bolts and ball joints for
proper tightness.
•Checking for installation and spread of cotter pins and tightness of
nuts at both ends of the tie rod and drag link.
204Maintenance
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

Periodically check:
•Condition of spring leaves for evidence of fatigue, bending or
breakage.
•Condition of suspension mounting brackets and bushings.
•Torque rod mounting fasteners for tightness.
•For proper suspension alignment. Maintain proper alignment at all
times.
•U-bolts. After the chassis has been operating under load for
1000 miles (1600 kilometers) or six months (whichever comes first),
the U-bolt nuts must be re-torqued. Re-torque the U-bolt nuts every
36000 miles (60000 kilometers) thereafter. Clean and lubricate the
U-bolt and nut threads and seats to make sure a like new condition
when re-torqueing.
Note:SeeSpring U-bolt checklater in this chapter.
Supporting Your Vehicle for Service
WARNING:Do not use a jack when working under a vehicle. It
may give way, causing the vehicle to fall and result in property
damage, personal injury or death. Always use floor stands to support
the vehicle.
Prepare your vehicle for service repairs by doing the following:
1. Park your vehicle on a level, concrete floor.
2. Set the parking brake and block the wheels to prevent your vehicle
from moving.
3. Select a jack with a rated capacity sufficient to lift and hold up your
vehicle.
4. Raise your vehicle with the jack applied to the axle(s). Do not use
the bumper as a lifting point.
5. Support your vehicle with floor stands under the axle(s). When
servicing the axle or the suspension, support your vehicle with floor
stands under the frame side-members, preferably between the axles.
Frame and Tow Hooks
Your vehicle’s chassis is manufactured with frame rails of either HSLA
steel or heat-treated steel. Handle each in a specific manner to make
sure maximum service life. Consult the service manual or an authorized
dealer before attempting frame repair or modification.
It is important, particularly on vehicles that use tow hooks frequently, to
inspect the front and rear tow hooks for damage or a loose mounting.
Maintenance207
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)

Daily Owner Checks
U.S. Department
of Transportation,
Federal Highway
Administration
Requirements
(Make sure the
entire system is
functioning
properly.)Service brakes and parking brake.
Steering mechanism.
Lighting devices and reflectors.
Tires.
Horn.
Windshield wipers.
Rear vision mirrors.
Wheels and rims.
Emergency equipment.
Every Oil Change
EngineInspect engine cooling system hoses, clamps and
protection.
*
Inspect drive belt(s).
Exhaust SystemInspect entire exhaust system (including the inlet
pipe(s), muffler(s), outlet pipe(s), clamps and
fasteners) for holes, leakage, breakage, corrosive
damage and separation from other components.
Adjust, service or replace with the same or the
equivalent part. (Also a noise emission control
service.)
SuspensionTighten the front and rear spring U-bolts to the
specified torque.
Driveline and
Rear AxleLubricate the U-joints and the slip yoke.
BrakesLubricate the air brake foot control valve, hinge
and roller.
Inspect the drum brake linings through the
inspection holes.
Lubricate the rear caliper slide rails.
Lubricate the brake camshafts and slack adjuster
(air brakes only).
Inspect the disc brake pads and the piston boots
(hydraulic brakes only).
342Scheduled Maintenance
2015 F-650/750(f67)
Owners Guide gf(ownloose), 1st Printing, December 2013
Canadian_French(fr_can)