2015 FIAT 500C turn signal bulb

NOTE:•A continuous chime will sound if the vehicle is
driven more than 1 mile (1.6 km) with either turn
signal on.
• Check for an inoperative outside light bulb if either
indicator remains on and does not flash, or flashes at
a rapid rate.
4. Electronic Stability Control (ESC) Activation/
Malfunction Indicator Light
The “ESC Activation/Malfunction Indicator
Light” in the instrument cluster will come on
when the ignition switch is turned to the
ON/RUN position. It should go out with the
engine running. If the “ESC Activation/Malfunction In-
dicator Light” comes on continuously with the engine
running, a malfunction has been detected in the ESC
system. If this light remains on after several ignition
cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see
your authorized dealer as soon as possible to have the
problem diagnosed and corrected.
NOTE:
•The “ESC Off Indicator Light” and the “ESC
Activation/Malfunction Indicator Light” come on
momentarily each time the ignition switch is turned
to ON/RUN.
• Each time the ignition is turned to ON/RUN, the
ESC system will be ON, even if it was turned off
previously.
• The ESC system will make buzzing or clicking
sounds when it is active. This is normal; the sounds
will stop when ESC becomes inactive following the
maneuver that caused the ESC activation.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 145

▫Automatic Transmission — If Equipped .....374
▫ Appearance Care And Protection From
Corrosion .......................... .376
▫ Convertible Top Care — If Equipped .......383
 FUSES ............................. .385
▫ Interior Fuses ....................... .386
▫ Underhood Fuses ..................... .388
 VEHICLE STORAGE ....................391
 REPLACEMENT BULBS .................392
 BULB REPLACEMENT ..................393
▫ Headlamps Low Beam and High Beam ......393▫
Front Turn Signal, Parking And Daytime Running
Lamps ............................ .394
▫ Front Fog Lamps ..................... .394
▫ Front/Rear Side Marker Lamps ............395
▫ Rear Tail, Stop, Backup And Turn Signal
Lamps ............................ .395
▫ Center High Mounted Stop Lamp (CHMSL) . . .396
 FLUID CAPACITIES ....................397
 FLUIDS, LUBRICANTS, AND GENUINE
PARTS ............................. .398
▫ Engine ............................ .398
▫ Chassis ........................... .400
344 MAINTAINING YOUR VEHICLE

REPLACEMENT BULBS
Interior Bulbs
Bulb Number
Overhead Lamp C5W
Courtesy Lamp W5W
Exterior Bulbs
Bulb Number
Front Low and High Beam Headlamp HIR2LL
Front Parking/Daytime Running Lamps W21/5W
Front Fog Lamps H11LL
Front Side Marker Lamps W3W
Front Turn Signal Lamps WY21W
Side Direction Lamps WY5W
Rear Turn Signal Lamps PY21W
Rear Side Marker Lamps W3W
392 MAINTAINING YOUR VEHICLE

Front Turn Signal, Parking And Daytime Running
Lamps
1. Turn the steering wheel completely to the left or right.
2. Open the wheel housing access door.3. Remove the plastic cap from the back of the lamp
housing.
4. Rotate bulb/socket counter-clockwise.
5. Remove the bulb and replace as needed.
6. Install the bulb into socket, and rotate bulb/socket clockwise into lamp locking it in place.
7. Reinstall the plastic cap.
Front Fog Lamps
To replace the front fog lights, see your authorized dealer.
Wheel Housing Access Door
394 MAINTAINING YOUR VEHICLE

Front/Rear Side Marker Lamps
1. Remove portion of the wheel liner to allow handaccess to side marker lamp.
2. Rotate the bulb socket counterclockwise, and remove the bulb and socket assembly from the housing.
3. Pull the bulb from the socket and insert the replace- ment bulb.
4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place.
5. Reinstall the wheel liner.
Rear Tail, Stop, Backup And Turn Signal Lamps
1. Open the liftgate.
2. Remove the two screws and remove the tail lamp assembly.
Tail Lamp Assembly Screws
7
MAINTAINING YOUR VEHICLE 395

3. Remove four screws and separate the backplate fromthe lamp housing.
4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise.
5. Remove the backup lamp bulb by pulling straight out.
6. Replace lamps as required and reinstall lamp.
Center High Mounted Stop Lamp (CHMSL)
1. Remove the two guard caps and the two fastening screws.
2. Remove the center high mounted stop lamp assembly. 3. Disconnect the electric connector.
4. Press the retaining device and open the bulb holder.
5. Remove the snap-fitted bulb to be replaced and re-
place it.
6. Close the back cap locking it properly.
7. Reinstall the two fastening screws and reinstall the guard caps.
396 MAINTAINING YOUR VEHICLE

Keys...................................11
Key, Sentry (Immobilizer) ....................13
Lane Change Assist ....................... .109
Lap/Shoulder Belts .........................29
Latches .................................78
Hood ............................... .104
Lead Free Gasoline .....................292, 293
Leaks, Fluid ..............................78
Life Of Tires ............................ .278
Liftgate (Sedan) ...........................25
Light Bulbs .......................... .78, 392
Lights .............................. .78, 106
AirBag .........................51, 76, 143
Anti-Lock ............................ .143
Brake Assist Warning ....................255
Brake Warning ........................ .143
Bulb Replacement ...................... .393
Check Engine (Malfunction Indicator) .........143Engine Temperature Warning
...............143
Exterior ...............................78
Fog ................................ .143
High Beam ....................... .107, 143
High Beam Indicator .....................143
Low Fuel ............................ .143
Oil Pressure .......................... .143
Park ............................... .107
Passing ............................. .107
Seat Belt Reminder ..................... .143
Service .............................. .393
Tire Pressure Monitoring (TPMS) ............143
Traction Control ....................... .255
Turn Signal ........................ .78, 108
Voltage ............................. .143
Warning (Instrument Cluster Description) ......143
Loading Vehicle Tires ............................... .263
10
INDEX 427