2015 CITROEN DS3 CABRIO DAG boot

201
DS3_en_Chap10_info-pratiques_ed01-2014
Important: if your vehicle's a
dblu e® tank is completely empty - w
hich
 
is
  confirmed   by   the   alert  
m

essages   and   the   impossibility   of  
s

tarting
 
the   engine,   you   must   add   at  
l

east
 
3.8   litres   (so   two   1.89   litre   bottles).If any additive is split or splashed, wash
immediately
  with   cold   water   or   wipe  
w

ith   a   damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up after
a breakdown because of a lack of
additive ,   signalled   by   the   message   "Top
 u

p   emissions   additive:   Starting   prevented",
 y

ou   must   wait   around   5   minutes   before
 s

witching  
o
n  
t
he  
i
gnition,  
w
ithout opening
the driver's door, locking the vehicle
or introducing the key into the ignition
switch .
Switch   on   the   ignition,   then,   after
 1

0 seconds,   start   the   engine.
F
o
b

tain a bottle of a
dbl
ue
®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
a
d
blu

e
® tank. N ever dispose of a
dbl
ue
® additive
bottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 
purpose
 
or
 
take
 
them
  to   your  
d

ealer.
F
 
A

fter
 
emptying
 
the
 
bottle,
 
wipe
 
away
 
any
 
s

pillage
 
around
 
the
 
tank
 
filler
 
using
 
a
 
damp
 
c

loth.
F
 
R

efit
 
the
 
blue
 
cap
 
to
 
the
 
tank
 
and
 
turn
 
it
 
a


6
th of a turn clockwise, to its stop.
F
 R
efit   the   black   cap   and   turn   it   a   quarter   of  
a

 
turn   clockwise   without   pressing.   Ensure  
t

hat the indicator on the cap lines up with
the
 
indicator   on   the   support.
F
 
D

epending   on   equipment,   return   the   spare  
w

heel   and/or   the   storage   box   to   the   bottom  
o

f
 
the   boot.
F
 
R

efit   the   boot   carpet   and   close   the   tailgate.
Practical information

207
DS3_en_Chap10_info-pratiques_ed01-2014
Changing a wheelProcedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
T he tools are installed in the boot under the
f l o o r.
To
  gain   access   to   them:
F

o
pen the boot,
F
 
l
ift   the   boot   carpet   by   pulling   the   strap  
up

wards,
F
 
r
emove   the   polystyrene   storage   box,
F
 
u
nclip   and   remove   the   box   containing   the  
to

ols.
Access to the tools
List of tools
All of these tools are specific to your vehicle. Do   not   use   them   for   other   purposes.
Wheel with trim
When removing the wheel , first
detach   the   trim   using   the   wheelbrace   1
pulling
  at   the   valve   passage   hole.
When refitting the wheel , refit the
trim
  starting   by   placing   its   cut-out   at   the  
v

alve   and   press   around   its   edge   with  
t

he   palm   of   your   hand.
3.
 "

Bolt   cover"   tool.
 F

or   removing   the   bolt   protectors   (covers)  
o

n   alloy   wheels.
4.
 S

ocket   for   the   security   wheel   bolts   (located  
i

n
  the   glove   box).
 F

or   adapting   the   wheelbrace   to   the   special  
s

ecurity wheel bolts (if your vehicle is fitted
with
  them)
1.
 W

heelbrace.
 F

or
 
removing
 
the
 
wheel
 
trim
 
and
 
removing
 
t

he
 
wheel
 
fixing
 
bolts.
2.
 J

ack
 
with
 
integral
 
handle.
 F

or
 
raising
 
the
 
vehicle.
Practical information

DS3_en_Chap10_info-pratiques_ed01-2014
The spare wheel is installed in the boot under
the  floor.
According
  to   country,   you   will   have   either   a  
"

space   saver"   spare   wheel   or   a   temporary  
p

uncture   repair   kit.
For
  access   to   it,   refer   to   the   paragraph   "Access  
t

o   the   tools"   on   the   previous   page.
Access to the spare wheel
Fitting the "space-saver"
type spare wheel
If your vehicle is fitted with alloy
wheels,  it   is   normal   to   notice,   when  
t

ightening   the   bolts   on   fitting,   that   the  
w

ashers   do   not   come   into   contact   with  
t

he   "space-saver"   type   spare   wheel.  
T

he wheel is secured by the conical
contact
  of   each   bolt.
Taking out the wheel
F Unscrew  the   yellow   central   bolt.
F  R aise   the   spare   wheel   towards   you   from  
t

he   rear.
F
 
T
ake   the   wheel   out   of   the   boot.

209
DS3_en_Chap10_info-pratiques_ed01-2014
Putting the wheel back in place
F Put  the   box   back   in   place   in   the   centre   of  t
he   wheel   and   clip   it.
F
 
P
ut   the   polystyrene   storage   box   back   in  
p

lace.
F
 
R
efit   the   boot   floor   carpet   by   lightly   folding  
i

t   in   the   middle   (refer   to   the   "Boot   fittings"  
s

ection).
F
 P
ut
 
the
 
wheel
 
back
 
in
 
its
 
housing.
F
U
nscrew the yellow central bolt by a few
turns then place it in the centre of the
wheel.
F
 
T

ighten
 
fully
 
until
 
the
 
central
 
bolt
 
clicks
 
to
 
r

etain
 
the
 
wheel
 
correctly.on v ehicles equipped with a "space-
saver" type spare wheel, the punctured
wheel can be stowed in place of the
"space-saver"
  wheel;   however   the   boot  
f

loor   will   not   then   be   flat.
Practical information

DS3_en_Chap10_info-pratiques_ed01-2014
Fitting a wheel
After changing a wheel
To store the punctured wheel in the
boot  correctly,   first   remove   the   central  
c

ove r.
When
  using   the   "space-saver"   type  
t

emporary-use   spare   wheel,   do   not  
e

xceed   50   mph   (80   km/h).
Have
  the   tightening   of   the   bolts   and   the  
p

ressure   of   the   spare   wheel   checked  
b

y a CITR
oË
N dealer or a qualified
workshop
  without   delay.
Have the punctured wheel repaired and
replace it on the vehicle as soon as
possible.
Do
  not   drive   with   more   than   one  
t

emporary-use   spare   wheel   fitted   to   the  
v

ehicle   at   one   time.
List of operations
F Put  the   wheel   in   place   on   the   hub.
F  S crew   in   the   bolts   by   hand.
F
 
P
re-tighten   the   security   bolt   (if   your   vehicle  
i

s   fitted   with   them)   using   the   wheelbrace   1
fitted
  with   the   socket   4.
F
 
P
re-tighten   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.

DS3_en_Chap10_info-pratiques_ed01-2014
1. Brake lamps / sidelamps (P21/5W).
2. Sidelamps (P5W).
3.
di

rection indicators (PY21W amber)
4.
F

oglamp, offside (PR21W red)


R
eversing lamp, nearside (P21W).
Rear lamps
Amber or red bulbs, such as those for the direction indicators and rear
foglamp,
  must   be   replaced   by   bulbs   of  
t

he   same   rating   and   colour.
changing bulbs
F Open  the   boot.
F  R emove   the   access   flap   from   the  
c

orresponding   side   trim   panel.
F
 
U
nscrew   the   butter fly   nut   securing   the  
lam

p
 u
nit.
F
 
U
nclip   the   lamp   unit   connector.
F
 
E
xtract   the   lamp   unit   carefully   pulling   in   its  
m

iddle   towards   the   outside. F
 S pread   the   four   tabs   and   remove   the   bulb  h
o l d e r.
F

T
urn the bulb a quarter of a turn and
change
 it

.
To refit, carry out these operations in reverse
o r d e r.
Take
  care   to   engage   the   lamp   unit   in   its   guides,  
w

hile   keeping   it   in   line   with   the   vehicle.

221
DS3_en_Chap10_info-pratiques_ed01-2014
changing direction indicator (4)
and foglamp or reversing
lamp
(5) bulbs
F Turn   the   bulb   a   quarter   turn   and   change   it.
changing LEd sidelamps and
brake lamps (LEds )
For the replacement of this type of LED lamp, c
ontact a CITRoË N dealer or a qualified
workshop.
3d rear lamps
Access to the bulbs
F Open   the   boot.
F  R emove   the   access   flap   from   the  
c

orresponding   side   trim   panel.
F
 
U
nscrew   the   butter fly   nut   securing   the  
lam

p
 u
nit.
F
 
U
nclip   the   lamp   unit   connector.
F
 
E
xtract   the   lamp   unit   carefully   pulling   it   in  
l

ine   towards   the   outside.
To
  refit,   carry   out   these   operations   in   reverse   order.
Take
  care   to   engage   the   lamp   unit   in   its   guides,  
w

hile   keeping   it   in   line   with   the   vehicle.
1.
3

d
L

E
d
s

idelamps (LE
d
s).
2. L
Ed
brake lamps / sidelamps (LEds
).
3. L
E
d la
teral sidelamps (LE
d
s).
4.
di

rection indicators (PY21W amber)
5.
F

oglamp, offside (H21W red)


R

eversing lamp, nearside (H21W).
Amber
 
or
 
red
 
bulbs,
 
such
 
as
 
those
 
f

or the direction indicators and rear
foglamp,
 
must
 
be
 
replaced
 
by
 
bulbs
 
of
 
t

he
 
same
 
rating
 
and
 
colour.
Practical information

DS3_en_Chap10_info-pratiques_ed01-2014
Third brake lamp (4 W5W bulbs)
F Open  the   boot.
F  R emove   the   plugs   A   on   the   inner   panel.
F
 
P
ush   on   the   centre   of   the   lamp   using   two  
s

crewdrivers   to   lever   it   outwards.
F

D
isconnect the connector and if necessary
the
  screenwash   pipe   from   the   lamp.
F

T
urn the bulb holder for the faulty bulb a
quarter
  of   a   turn.
F
 
P
ull   out   the   bulb   and   change   it.
To refit, carry out these operations in reverse
o r d e r.
Third brake lamp (LEds )
For the replacement of this type of LED lamp, c
ontact a CITRoË N dealer or a qualified
workshop.
changing the number plate lamp
bulbs (W5W)
F Insert a thin screwdriver into one of the outer   holes   of   the   lens.
F
 
P
ush   it   outwards   to   unclip.
F
 
R
emove   the   lens.
F
 
P
ull   the   bulb   out   and   change   it.