2015 Citroen C4 PICASSO lock

197
To make your approach to the vehicle easier, these   illuminate:
-
 
t
he   zones   facing   the   driver’s   and  
p

assenger’s
 do
ors,
-
 
t
he   zones   for ward   of   the   door   mirrors   and  
r

ear ward   of   the   front   doors.
Door mirror spotlamps
Switching on
The spotlamps come on automatically:- when  you   unlock   the   vehicle,- when  you   remove   the   electronic   key   from   the   reader,- when  you   open   a   door,- when  you   use   the   remote   control   to   locate   the v
ehicle.
Switching off
They go off automatically after 30 seconds.
Exterior welcome lighting
Switching on
F Press   the   open   padlock   on   the  r
emote   control   or   one   of   the   front  
d

oor   handles   with   Keyless   Entry  
an

d
 S
tarting.
 T

he   dipped   beam   headlamps  
a

nd   the   sidelamps   come   on;   your  
v

ehicle   is   also   unlocked.
Programming
Daytime running lamps
(LEDs)
They come on automatically when the engine is   started,   when   the   lighting   control   stalk   is   in  
p

osition " 0" or " AUTO ".
In
  some   weather   conditions   (e.g.   low  
t

emperature   or   humidity),   the   presence  
o

f   misting   on   the   internal   sur face   of   the  
g

lass   of   the   headlamps   and   rear   lamps  
i

s   normal;   it   disappears   after   the   lamps  
h

ave   been   on   for   a   few   minutes. The
  remote   switching   on   of   the   lighting   makes  
y

our approach to the vehicle easier in poor
light.   It   is   activated   when   the   lighting   control  
i

s in the "
AUTO"   position   and   the   level   of   light  
d

etected   by   the   sunshine   sensor   is   low.
Switching off
The activation, deactivation and choice of w
elcome   lighting   duration   are   done   in   the  
"D

riving assistance "
  menu   then   "Vehicle
settings ".
The
  exterior   welcome   lighting   switches   off  
a

utomatically   after   a   set   time,   when   the   ignition  
i

s   switched   on   or   on   locking   the   vehicle.
5
Visibility

203
Screenwash and washer jets
Windscreen wash and
headlamp wash
Adjusting the jets
The f ront  w ashers  i nclude  a n  a djustment  f or  t he  
h

eight   of   delivery   from   the   jets.
If
  you   want   to   modify   the   factory   setting,   turn  
t

he   screw   on   each   jet   anti-clockwise,   towards  
t

he   "+"   to   raise   the   jet   or   clockwise,   towards  
t

he "-"   to   lower   it.
Headlamp wash
F Pull  the   windscreen   wiper   stalk   towards  y
ou.   The   windscreen   wash   then   the  
w

indscreen   wipers   operate   for   a   fixed  
p

eriod.
A
  few   moments   after   releasing   the   wiper   stalk,  
t

here   is   a   last   wipe   to   clear   any   runs   from   the  
sc

reen. The
  headlamps   operate   when   the   vehicle   is  m
oving   and   when   the   dipped   beam   headlamps  
a

re   on.   However,   to   reduce   the   consumption  
o

f   screenwash   fluid,   the   headlamp   wash   only  
o

perates   with   every   7th   use   of   the   screenwash  
o

r   once   every   25   miles   (40   km),   during   a   given  
j

o u r n ey.
5
Visibility

206
Courtesy lamps
1. Front  courtesy   lamp
2. F ront   map   reading   lamps
3.
 R

ear   courtesy   lamp
4.
 R

ear   map   reading   lamps
Front - rear courtesy lamps
F With  the   ignition   on,   press   the  c
orresponding s witch.
Front - rear map reading
lamps
With the "permanent lighting" mode, the lighting time   varies   according   to   the   circumstances:
- with  the   ignition   off,   approximately t
en minutes,
- in   energy   economy   mode,   approximately t
hirty   seconds,
- with  the   engine   running,   unlimited.
In this position, the courtesy lamp c
omes   on   gradually:
Permanently
  off.
Permanent
 l

ighting.
-
 
w

hen
  the   vehicle   is   unlocked,
-
 
w

hen
  the   electronic   key   is   removed   from  
t

he
 r

eader,
-
 
w

hen
  opening   a   door,
-
 
w

hen
  the   remote   control   locking   button   is  
u

sed,
  in   order   to   locate   your   vehicle.
It
 
switches   off   gradually:
-
 
w

hen
  the   vehicle   is   locked,
-
 
w

hen
  the   ignition   is   switched   on,
-
 
3

0
 
seconds   after   the   last   door   is   closed.Take
  care   to   avoid   leaving   anything   in  
c

ontact   with   the   courtesy   lamps.
Depending
 o

n
 v

ersion, you can
also switch the
courtesy
  lamp   on   or  
o

ff   by   pressing   this  
b

utton.
Visibility

214
Electronic Stability Control (ESC) incorporating the   following   systems:
-
 
a
nti-lock   braking   system   (ABS)   and   the  
e

lectronic   brake   force   distribution   (EBFD),
-
 
e
mergency   braking   assistance   (EBA),
-
 
w
heel   anti-slip   regulation   (ASR)   or   traction  
c

ontrol,
-
 
d
ynamic   stability   control   (DSC).
Electronic stability control (ESC)
Definitions
Anti-lock braking system (ABS)
and electronic brake force
distribution (EBFD)
This system improves the stability and manoeuvrability   of   your   vehicle   when   braking  
a

nd   contributes   towards   improved   control   in  
c

orners,   in   particular   on   poor   or   slippery   road  
su

rfaces.
The
  ABS   prevents   wheel   lock   in   the   event   of  
em

ergency
 b
raking.
The
  electronic   brake   force   distribution   system  
m

anages   the   braking   pressure   wheel   by   wheel.
Emergency braking assistance
(EBA)
In an emergency, this system enables you to reach   the   optimum   braking   pressure   more  
q

uickly   and   therefore   reduce   the   stopping  
di

stance.
It
  is   triggered   according   to   the   speed   at   which  
t

he   brake   pedal   is   pressed.   This   is   felt   by   a  
r

eduction   in   the   resistance   of   the   pedal   and   an  
i

ncrease   in   the   effectiveness   of   the   braking.
Anti-slip regulation (ASR)
The ASR system (also known as Traction Control)   optimises   traction   in   order   to   limit  
w

heel   slip   by   acting   on   the   brakes   of   the   driving  
w

heels   and   on   the   engine.   It   also   improves  
t

he   directional   stability   of   the   vehicle   on  
a

cceleration.
Dynamic stability control (DSC)
If there is a difference between the path followed   by   the   vehicle   and   that   required   by  
t

he   driver,   the   DSC   monitors   each   wheel   and  
a

utomatically   acts   on   the   brake   of   one   or   more  
w

heels   and   on   the   engine   to   return   the   vehicle  
t

o   the   required   path,   within   the   limits   of   the   laws  
o

f   physics.
Safety

215
Intelligent traction control
system ("Snow motion")
When this warning lamp comes on, coupled   with   the   STOP w arning lam p, a

ccompanied   by   an   audible   signal   and   a
 m

essage,   it   indicates   that   there   is   a   fault
 w

ith   the   electronic   brake   force   distribution
 (

EBFD),   which   could   cause   loss   of   control
 o

f   the   vehicle   when   braking.
Operation
When this warning lamp comes on, accompanied   by   an   audible   signal  
a

nd   a   message,   it   indicates   that   there  
i

s   a   fault   with   the   ABS,   which   could  
c

ause loss of control of the vehicle
when
 b

raking. Depending
  on   version,   your   vehicle   has   a  
s

ystem   to   help   driving   on   snow:   intelligent
traction control .
This   system   detects   situations   of   difficult  s
ur face   adhesion   that   could   make   it   difficult   to  
m

ove   off   or   make   progress   on   deep   fresh   snow  
o

r   compacted   snow.
In these situations, the intelligent traction
control
 

limits   the   amount   of   wheel   slip   to  
p

rovide   the   best   traction   and   trajectory   control  
f

or   your   vehicle.
The
  use   of   snow   tyres   is   strongly  
r

ecommended   on   sur faces   offering   low   levels  
o

f   adhesion.
Anti-lock braking system (ABS)
and electronic brake force
distribution (EBFD)When changing w heels  ( tyres  a nd  r ims),  m
ake   sure   that   these   are   approved   for  
y

our   vehicle.
Normal
  operation   of   the   ABS   may   make  
i

tself   felt   by   slight   vibrations   of   the   brake  
ped

al.
In emergency braking, press
very firmly without releasing the
pressure.
You must stop as soon as it is safe to do so.
In
 
both
 
cases,
 
contact
 
a
 
CITROËN
 
dealer
 
or
 
a
 
q

ualified
 w

orkshop.
6
Safety

247
Child seats
The incorrect installation of a child seat in a vehicle   compromises   the   child's   protection   in  
t

he   event   of   an   accident.
Check
  that   there   is   no   seat   belt   or   seat   belt  
b

uckle   under   the   child   seat   as   this   could  
de

stabilise
 i
t.
Remember
  to   fasten   the   seat   belts   or   the  
c

hild   seat   harnesses   keeping the slack in
relation
  to   the   child's   body   to a minimum,
even
  for   short   journeys.
For
  the   installation   of   a   child   seat   using   a  
s

eat   belt,   ensure   that   this   is   well   tensioned  
o

n   the   child   seat   and   that   it   is   holding   the  
c

hild   seat   firmly   against   the   seat   of   your  
v

ehicle.   If   your   front   passenger   seat   is  
a

djustable,   move   it   for ward   if   necessary.
at t

he rear seats, always leave sufficient
space
  between   the   front   seat   and:
-
 
a
  rear ward   facing   child   seat,
-
 
t
he   feet   of   a   child   seated   in   a   for ward  
f

acing   child   seat.
Recommendations
For this, move the front seat for ward and if necessary   straighten   its   backrest.
For
 o

ptimum
 in
stallation
 o
f
 t
he
 fo
rward
 f
acing
 c

hild   seat,   ensure   that   the   back   of   the   child  
s

eat   is   as   close   as   possible   to   the   backrest  
o

f   the   vehicle's   seat,   or   in   contact   if   possible.
The
  head   restraint   must   be   removed   before  
i

nstalling   a   child   seat   with   a   backrest   on   the  
p

assenger
 sea
t.
Ensure
  that   the   head   restraint   is   stowed   or  
a

ttached   securely   so   that   it   is   not   thrown  
a

round   the   vehicle   in   the   event   of   sharp  
b

raking.
Refit
  the   head   restraint   as   soon   as   the   child  
s

eat   is   removed.Installing a booster
cushion
As a safety precaution, do not leave:
-  o ne   or   more   children   alone   and  
u

nsupervised   in   a   vehicle,
-
 
a
  child   or   an   animal   in   a   vehicle   which  
i

s   exposed   to   the   sun,   with   the   windows  
c

losed,
-
 
t
he   keys   within   reach   of   children   inside  
t

he   vehicle.
To
  prevent   accidental   opening   of   the   doors,  
u

se   the   child   lock.
Take
  care   not   to   open   the   rear   windows   by  
m

ore   than   one   third.
To
  protect   young   children   from   the   rays   of  
t

he   sun,   fit   side   blinds   on   the   rear   windows.
The
  chest   part   of   the   seat   belt   must   be  
p

ositioned   on   the   child's   shoulder   without  
t

ouching   the   neck.
Ensure that the lap part of the seat belt
passes   correctly   over   the   child's   thighs.
CITROËN   recommends   the   use   of   a   booster  
s

eat   which   has   a   back,   fitted   with   a   seat   belt  
g

uide   at   shoulder   level.
The
 
legislation
 
on
 
carrying
 
a
 
child
 
on
 
the
 
f

ront
 
passenger
 
seat
 
is
 
specific
 
to
 
each
 
c

ountry.
 
Refer
 
to
 
the
 
legislation
 
in
 
force
 
in
 
t

he
 
country
 
in
 
which
 
you
 
are
 
driving.
Deactivate
 
the
 
passenger's
 
front
 
airbag
 
w

hen
 
a
 
rear ward
 
facing
 
child
 
seat
 
is
 
installed
 
o

n
 
the
 
front
 
passenger
 
seat.
 
Other wise,
 
the
 
c

hild
 
would
 
risk
 
being
 
seriously
 
injured
 
or
 
k

illed
 
if
 
the
 
airbag
 
were
 
deployed.
Children at the front
6
Safety

248
Child lock
This mechanical system prevents opening of a rear door using its interior control.
T he   control   is   located   on   the   edge   of   each   rear   door   and   locking   is   independent   for   each   door.
Locking
F Using  the   integral   ignition   key,   turn   the   control   as   far   as   it   will   go:
-  t o   the   left   on   the   left-hand   rear   door,
-
 
t
o   the   right   on   the   right-hand   rear   door.
Unlocking
F Using  the   integral   ignition   key,   turn   the   control   as   far   as   it   will   go:
-  t o   the   right   on   the   left-hand   rear   door,
-
 
t
o   the   left   on   the   right-hand   rear   door.
Safety

260
Taking out the spare wheelThe spare wheel is supported by a carrier underneath t he v ehicle.
Access to the spare wheel*
F Take  out   the   wheel   /   tool   box   assembly  f
rom   the   rear   of   the   vehicle.
F
 
S
traighten   the   spare   wheel   for   access   to  
t

he   tools   (A ).
F
 
F

old
 
the
 
concertina
 
board
 
and
 
put
 
the
 
left
 
h

and
 
third
 
row
 
seat
 
into
 
position
 
(if
 
your
 
v

ehicle
 
has
 
them).
F
 
R

aise
 
the
 
pre-cut
 
section
 
of
 
carpet
 
to
 
e

xpose
 
the
 
nut
 
for
 
operating
 
the
 
spare
 
w

heel
 
carrier.
F
 
U

sing
 
the
 
extension
 
6
 
fitted
 
to
 
the
 
end
 
of
 
t

he wheelbrace 1 ,
 
turn
 
the
 
nut
 
clockwise
 
t

o
 
unwind
 
the
 
carrier
 
cable
 
until
 
the
 
spare
 
w

heel
 
reaches
 
the
 
ground.
 
Unwind
 
the
 
l

ength
 
needed
 
for
 
access
 
to
 
the
 
wheel.
Only
 
a
 
"space-saver"
 
type
 
of
 
spare
 
w

heel
 
can
 
be
 
fitted
 
under
 
the
 
vehicle.
*
 
Depending
 
on
 
version. F
 
D
etach   the   link   piece   from   the   tool   box  
l

id (B - C ).
F
 
P
ass   the   link   piece   through   the   middle   of  
t

he   wheel   to   free   it   (D ).
Practical information