2015 Citroen C ZERO ignition

7
C-zero_en_Chap00b_vue-ensemble_ed01-2014
Instruments and controls
1. Steering lock and ignition switch.
2. Wi per stalk.
3.
Wi

ndscreen demisting vents.
4.
Gl

ove box.
Pa

ssenger's airbag deactivation.
5.
Bo

nnet release lever.
6.
Pa

rking brake.
7.
Dr

ive selector.
8.
12 V a

ccessory socket.
9.
He

ating
/ a
ir conditioning controls.
10.
Em

ergency or assistance call.
11.
Ha

zard warning switch.
12 .
Ce

ntre vents.
13.
Au

dio system.
.
Over view

10
C-zero_en_Chap01_controle-de-marche_ed01-2014
Indicator and warning lamps
Visual indicators informing the driver that a
system is in operation, is deactivated or has
a
f
ault.Associated warnings
The illumination of certain warning lamps may
be accompanied by an audible signal.
The warning lamps may come on continuously
(fixed) or flash.
Certain warning lamps may come on in
one of two modes. Only by relating the
type of lighting to the operating status
of the vehicle can it be ascertained
whether the situation is normal or
whether a fault has occurred.
When the ignition is switched on
Certain warning lamps come on for a few seconds
when the vehicle's ignition is switched on.
These same warning lamps go off after a few
seconds.
If you notice one of these warning lamps
remaining on, refer to the information on the
warning lamp in question.
Monitoring

17
C-zero_en_Chap01_controle-de-marche_ed01-2014
AirbagsOn temporarily. When you switch on the ignition, this
warning lamp comes on for a few
seconds, then goes off. If it does not go off, contact a CITROËN dealer or a
qualified workshop.
On fixed. Fault with one of the airbag or seat
belt pretensioner systems. Have it checked by a CITROËN dealer or a qualified
workshop.
Protection
system for the
main battery On fixed.
The state of charge of the main
battery is too low or the temperature
of the main battery is too low... The power from the motor is limited.
Charge the main battery as soon as possible.
If the warning lamp does not go off, contact a
CITROËN dealer or qualified workshop.
Self-diagnosis
system of the
main electrical
circuit On fixed.
Fault in the main electrical circuit. You must stop as soon as it is safe to do so.
Have it checked by a CITROËN dealer or a qualified
workshop.
Warning
/

indicator lamp
State Cause Action
/
Observations
1
Monitoring

19
C-zero_en_Chap01_controle-de-marche_ed01-2014
Energy consumption / generation indicator
Energy consumption
On switching on the ignition, your vehicle
neither consumes nor generates energy in its
electric traction system: the needle is in the
"neutral" position (provided that the heating and
air conditioning are off).
"Eco" zone
A system that informs the driver of the level of energy consumption or generation of the main battery.
"Neutral" position"Charge" zone
The needle moves to the right in proportion to
the energy consumption by the vehicle.The needle is in this zone when the vehicle is
used so as to moderate electric consumption
and optimise its range.
The needle moves to the left in proportion to
the level of charge sent to the main battery,
during period of deceleration and braking.
1
Monitoring

20
C-zero_en_Chap01_controle-de-marche_ed01-2014
Instrument panel screenWhen the ignition switch is in the "ON" position, press button A repeatedly to display the following information in turn.
Distance recorder
System for measuring the total distance
travelled by the vehicle during its life.
Press button A .
The total distance appears in the screen.Reset to zero
With the ignition on and either trip A or B
displayed, press the button for more than
2
s

econds.
Trip distance recorder (Trip A or B)
Each of these trip recorders indicates the
distance travelled since the last reset.
Press button A to display the desired trip.
Monitoring

21
C-zero_en_Chap01_controle-de-marche_ed01-2014
Service indicator
When the ignition is switched on, press
button A several times in succession until the
service indicator is displayed in the desired
units. This point can be indicated in one of two ways:
-
th
e miles (km) remaining,
-
th
e time remaining to the next service.
Operation
1. The screen indicates that 620 miles
(
1000 k m) or 1 month remain before the
next service.
2.
Th

e screen indicates that the date for the
service has been exceeded.
Ev

ery time the ignition is switched on,
the service spanner is displayed for a
few seconds to remind you that a service
should be carried out as soon as possible.
3.
On

ce the service has been carried out, the
distance or the number of months to the
next service is displayed again.
System which informs the driver when the
next service is due in accordance with the
manufacturer's servicing schedule.
The point at which the next service is due
is calculated from the last service indicator
zero
r

eset.
System for manual adjustment of the
brightness of the instruments and controls in
relation to the exterior brightness.
With the lighting on or off, press button A to
select the function, then hold down to change
the intensity of the lighting of the instruments
and controls in "day" or "night" mode.
The intensity of the lighting increases each time
button A is pressed.
When the lighting reaches the maximum
setting, press again to change to the minimum
setting.
When the lighting reaches the required
intensity, release button A .
The setting is saved when you release button A
and retained when the ignition switch is turned
to OFF.
Lighting dimmer
1
Monitoring

22
C-zero_en_Chap01_controle-de-marche_ed01-2014
The display of "---", indicating that the
service date has arrived, comes on
automatically after a certain time and
distance travelled. The screen then
indicates the time remaining before the
next service is due.
Resetting the service indicator to zero
After each service, the service indicator should
be rest to zero.
The procedures is as follows:
F
Sw

itch off the ignition (switch in the LOCK
or ACC position).
F
Pr

ess the reset button A several times in
succession until the service indicator is
displayed.
F
Pr

ess and hold the reset button for a few
seconds until the spanner flashes .
F
Pr

ess the reset button while the spanner is
flashing to change the display from "---" to
"CLEAR" .
Th

e distance (or time) remaining before the
next service is due is displayed.
Monitoring

25
C-zero_en_Chap02_ouvertures_ed01-2014
Anti-theft protection
Electronic immobiliser
The key contains an electronic chip which has
a special code. When the ignition is switched
on, this code must be recognised to permit
starting.
This electronic immobiliser locks the control
system a few moments after the ignition is
switched off and prevents starting by anyone
who does not have the key.
In the event of a malfunction and if your vehicle
does not start, contact a CITROËN dealer as
soon as possible.
Remote control problem
In the event of a remote control malfunction,
you can neither unlock nor lock your vehicle.
F
Fi
rst of all, use the key in the driver's door
lock to unlock or lock your vehicle.
F
Th

en, contact a CITROËN dealer to check
the operation of the remote control and
replace the battery if necessary.
2
Access