▷If possible, do not remove foreign bodies
that have penetrated the tire.▷Pull the speed limit sticker off the sealant
container and apply it to the steering
wheel.▷The use of a sealant can damage the TPM
wheel electronics. In this case, have the
electronics checked at the next opportu‐
nity and have them replaced if needed.
Enclosed areas
Do not let the engine run in enclosed
areas, since breathing in exhaust fumes may
lead to loss of consciousness and death. The
exhaust gases contain carbon monoxide, an
odorless and colorless but highly toxic gas.◀
Storage The Mobility System is located under the
cargo floor panel.
Sealing container
▷Sealing container, arrow 1.▷Filling hose, arrow 2.
Observe use-by date on the sealant container.
Compressor1Holder for bottle2Compressor3Connector/cable for socket4Connection hose5On/off reel6Inflation pressure dial7Reduce inflation pressure
Filling the tire with sealant
1.Shake the sealing container.2.Pull the connection hose fully out of the
compressor housing. Do not kink the hose.Seite 178MobilityWheels and tires178
Online Edition for Part no. 01 40 2 959 695 - II/15
3.Screw the connection hose onto the con‐
nector of the sealant container.4.Insert the sealant container on the com‐
pressor housing in an upright position.5.Screw the filling hose of the sealant con‐
tainer onto the tire valve of the defective
wheel.6.With the compressor switched off, insert
the plug into the power socket inside the
vehicle.7.With the ignition turned on or the engine
running, reel on the compressor.
Switch off the compressor after 10 mi‐
nutes
Do not allow the compressor to run longer than
10 minutes; otherwise, the device will overheat
and may be damaged.◀
Let the compressor run for approx. 3 to 8 mi‐
nutes to fill the tire with sealant and achieve a
tire inflation pressure of approx. 2.5 bar.
While the tire is being filled with sealant, the
tire inflation pressure may sporadically reach
approx. 5 bar. Do not reel off the compressor at
this point.
If a tire inflation pressure of 2 bar is not
reached:
1.Switch off the compressor.2.Unscrew the filling hose from the wheel.3.Drive 33 ft/10 m forward and back to dis‐
tribute the sealant in the tire.4.Inflate the tire again using the compressor.Seite 179Wheels and tiresMobility179
Online Edition for Part no. 01 40 2 959 695 - II/15
If a tire inflation pressure of 2 bar cannot be
reached, contact your service center.
Stowing the Mobility System
1.Unscrew the filling hose of the sealant con‐
tainer from the wheel.2.Unscrew the connection hose of the com‐
pressor from the sealant container.3.Connect the filling hose of the sealant con‐
tainer previously connected to the tire
valve with the available connector on the
sealant container.
This prevents leftover sealant from escap‐
ing from the container.4.Wrap the empty sealant container in suita‐
ble material to avoid dirtying the cargo
area.5.Stow the Mobility System back in the vehi‐
cle.
Distributing the sealant
Immediately drive approx. 5 miles/10 km to en‐
sure that the sealant is evenly distributed in the
tire.
Do not exceed a speed of 50 mph/80 km/h.
If possible, do not drive at speeds less than
12 mph/20 km/h.
To correct the tire inflation pressure
1.Stop at a suitable location.2.Screw the connection hose of the com‐
pressor directly onto the tire valve stem.3.Insert the connector into the power socket
inside the vehicle.4.Correct the tire inflation pressure to
2.5 bar.▷Increase pressure: with the ignition
turned on or the engine running, reel
on the compressor.▷To reduce the pressure: press the but‐
ton on the compressor.Continuing the trip
Do not exceed the maximum permissible
speed of 50 mph/80 km/h.
Reinitialize the Flat Tire Monitor.
Reinitialize the Tire Pressure Monitor.
Replace the defective tire and the sealant con‐
tainer of the Mobility System as soon as possi‐
ble.
Snow chains Fine-link snow chains
Only certain types of fine-link snow chains
have been tested by the manufacturer of the
vehicle, classified as road-safe and approved.
Information about the approved snow chains
are available from the service center.
Use
Use only in pairs on the rear wheels, equipped
with the tires of the following size:▷255/40 R 19▷255/35 R 20
Follow the snow chain manufacturer's instruc‐
tions.
Make sure that the snow chains are always
sufficiently tight. Retighten as needed accord‐
ing to the chain manufacturer's instructions.
Do not initialize the Flat Tire Monitor after
mounting snow chains, as doing so may result
in incorrect readings.
Do not initialize the Tire Pressure Monitor after
mounting snow chains, as doing so may result
in incorrect readings.
When driving with snow chains, if needed
briefly activate M Dynamic Mode.
Maximum speed with snow chains
Do not exceed a speed of 30 mph/50 km/h
when using snow chains.
Seite 180MobilityWheels and tires180
Online Edition for Part no. 01 40 2 959 695 - II/15
Tail lights, bulb replacement
At a glance1Turn signal/brake lamp2Reversing lamp3Inside brake lamp4Rear lamp5Outside brake lamp6Rear reflector
Turn signal, outer brake, tail, and
license plate lights
Follow general instructions, refer to page 189.
These lights feature LED technology.
Contact your service center in the event of a
malfunction.
Lights in the trunk lid
Access to the lights
If necessary, remove the fasteners using the
screwdriver from the onboard vehicle tool kit
and fold away the cover.
Inside brake lamp
Follow general instructions, refer to page 189.
24-watt bulb, HP24W.1.Squeeze the bulb holder and pull it out.2.Pull off the connector.3.Replace the bulb.4.Mount the bulb holder and the cover of the
trunk lid in reverse order.
Reversing lamp
Follow general instructions, refer to page 189.
16-watt bulb, W16W.
1.Unscrew the bulb holder counterclockwise.2.Pull out the bulb and replace it.3.Mount the bulb holder and the cover of the
trunk lid in reverse order.
Changing wheels
Hints
When sealants are used, an immediate wheel
change when there is a loss of tire inflation
Seite 191Replacing componentsMobility191
Online Edition for Part no. 01 40 2 959 695 - II/15
corresponding engine or body ground of
the vehicle to be started.
Starting the engine
Never use spray fluids to start the engine.
1.Start the engine of the assisting vehicle
and let it run for several minutes at an in‐
creased idle speed.2.Start the engine of the vehicle that is to be
started in the usual way.
If the first starting attempt is not success‐
ful, wait a few minutes before making an‐
other attempt in order to allow the dis‐
charged battery to recharge.3.Let both engines run for several minutes.4.Disconnect the jumper cables in the re‐
verse order.
Check the battery and recharge if needed.
Tow-starting and towing Note Tow-starting and towing
For tow-starting or towing, switch off the
Intelligent Safety systems; otherwise malfunc‐
tions of the individual braking systems might
lead to accidents.◀
Manual transmission
Observe before towing your vehicle Gearshift lever in neutral position.
Towing When the parking brake is blocked
The parking brake cannot be released
manually.
Do not tow the vehicle with the parking brake
blocked, or the vehicle can be damaged.
Contact your service center.◀
Follow the towing instructions
Follow all towing instructions; otherwise,
vehicle damage or accidents may occur.◀▷Make sure that the ignition is switched on;
otherwise, the low beams, tail lights, turn
signals, and wipers may be unavailable.▷Do not tow the vehicle with the rear axle
tilted, as the front wheels could turn.▷When the engine is stopped, there is no
power assist. Consequently, more force
needs to be applied when braking and
steering.▷Larger steering wheel movements are re‐
quired.▷The towing vehicle must not be lighter
than the vehicle being towed; otherwise,
it will not be possible to control the vehi‐
cle's response.
Tow truck
Have your vehicle transported with a tow truck
with a so-called lift bar or on a flat bed.
Do not lift the vehicle
Do not lift the vehicle by the tow fitting or
body and chassis parts; otherwise, damage
may result.◀
Seite 197Breakdown assistanceMobility197
Online Edition for Part no. 01 40 2 959 695 - II/15
Exhaust system 159
Exterior mirror, automatic dimming feature 57
Exterior mirrors 56
External start 196
External temperature dis‐ play 83
External temperature warn‐ ing 83
Eyes for securing cargo 163
F
Failure message, see Check Control 79
False alarm, refer to Uninten‐ tional alarm 45
Fan, refer to Air flow 140
Filler neck for engine oil 184
Fine wood, care 202
First aid kit 195
Fitting for towing, see Tow fit‐ ting 198
Flat tire, changing wheels 191
Flat Tire Monitor FTM 106
Flat tire, repairing 177
Flat tire, Tire Pressure Moni‐ tor TPM 103
Flat tire, warning lamp 104, 106
Flooding 160
Floor carpet, care 203
Floor mats, care 203
Fold-out position, wiper 71
Foot brake 160
For the roofliner, refer to All around the interior rearview
mirror 17
Front airbags 100
Front center armrest 151
Front-end collision warning with City Braking func‐
tion 108
Front lights 189 front-seat passenger airbags,
automatic deactivation 102
Front-seat passenger airbags, indicator lamp 102
Front seats 49
FTM Flat Tire Monitor 106
Fuel 170
Fuel consumption, refer to Average fuel consump‐
tion 89
Fuel filler flap 168
Fuel gauge 82
Fuel lid 168
Fuel quality 170
Fuel recommendation 170
Fuel, tank capacity 207
Fuse 193
G
Garage door opener, refer to Universal Integrated Remote
Control 144
Gasoline 170
Gear change 74
Gear shift indicator 86
General driving notes 159
Glare shield 146
Glass sunroof, powered with tilt function 46
Glove compartment 150
Gross vehicle weight, ap‐ proved 206
Ground clearance 161
H
Handbrake, refer to Parking brake 67
Hand-held transmitter, alter‐ nating code 145
Hazard warning flashers 194
Head airbags 100
Headlight control, auto‐ matic 96 Headlight courtesy delay fea‐
ture 95
Headlight courtesy delay fea‐ ture via remote control 38
Headlight flasher 69
Headlight glass 190
Headlights 189
Headlights, care 201
Headlight washer system 69
Head restraints 49
Head restraints, front 53
Head-up Display 92
Head-up Display, care 203
Head-up display, M view 93
Head-up display, standard view 93
Heavy cargo, stowing 163
Height, seats 49
Height, vehicle 206
High-beam Assistant 97
High beams 69
High beams/low beams, refer to High-beam Assistant 97
Higher speed range 161
Hills 160
Hill start assistant, refer to Drive-off assistant 122
Hints 6
Holder for beverages 152
Homepage 6
Hood 181
Horn 14
Hotel function, trunk lid 41
Hot exhaust system 159
HUD Head-up Display 92
Hydroplaning 159
I Ice warning, see External temperature warning 83
Icy roads, see External tem‐ perature warning 83
Identification marks, tires 173 Seite 211Everything from A to ZReference211
Online Edition for Part no. 01 40 2 959 695 - II/15
Identification number, see ve‐hicle identification num‐
ber 9
iDrive 18
Ignition key, refer to Remote control 34
Ignition off 63
Ignition on 63
Indication of a flat tire 104 , 106
Indicator and alarm lamps, see Check Control 79
Indicator lamp, see Check Control 79
Individual air distribution 140
Individual settings, refer to M Drive 122
Individual settings, refer to Personal Profile 35
Inflation pressure, tires 172
Inflation pressure warning FTM, tires 106
Info display, refer to On- Board computer 88
Initialize, Tire Pressure Moni‐ tor TPM 104
Initializing, Flat Tire Monitor FTM 106
Instrument cluster 78
Instrument cluster, electronic displays 78
Instrument lighting 98
Integrated key 34
Integrated Owner's Manual in the vehicle 29
Intelligent Emergency Re‐ quest 194
Intelligent Safety 107
Intensity, AUTO pro‐ gram 140
Interior equipment 144
Interior lights 98
Interior lights during unlock‐ ing 37
Interior lights with the vehicle locked 38 Interior motion sensor 44
Interior rearview mirror, auto‐ matic dimming feature 57
Internet page 6
Interval display, service re‐ quirements 85
Interval mode 70
J Jacking points for the vehicle jack 192
Jump-starting 196
K
Key/remote control 34
Keyless Go, refer to Comfort Access 41
Key Memory, refer to Per‐ sonal Profile 35
Knee airbag 101
L Lamp replacement, front 189
Lamp replacement, rear 191
Lane departure warning 116
Lane margin, warning 116
Language on Control Dis‐ play 92
Lashing eyes, securing cargo 163
LATCH child restraint sys‐ tem 61
Launch Control 75
Leather, care 202
LED headlights, bulb replace‐ ment 190
LED light 190
LEDs, light-emitting di‐ odes 190
Length, vehicle 206
Letters and numbers, enter‐ ing 24 License plate lamp, bulb re‐
placement 191
Light alloy wheels, care 202
Light control 96
Light-emitting diodes, LEDs 190
Lighting 95
Lighting, speaker 99
Lights 95
Lights and bulbs 189
Light switch 95
Load 163
Loading 162
Lock, door 39
Locking/unlocking via door lock 39
Locking/unlocking with re‐ mote control 37
Locking, automatic 43
Locking, settings 42
Locking via trunk lid 40
Low beams 95
Low beams, automatic, refer to High-beam Assistant 97
Lower back support 50
Low Speed Assistant 73
Lumbar support 50
M
Maintenance 187
Maintenance require‐ ments 187
Maintenance, service require‐ ments 85
Maintenance system, BMW 187
Make-up mirror 146
Malfunction displays, see Check Control 79
Manual air distribution 140
Manual air flow 140
Manual brake, refer to Parking brake 67
Manual operation, door lock 39 Seite 212ReferenceEverything from A to Z212
Online Edition for Part no. 01 40 2 959 695 - II/15
Transmission, manual trans‐mission 77
Transporting children safely 59
Tread, tires 175
Trip computer 90
Triple turn signal activa‐ tion 69
Trip odometer 83
Truck for tow-starting/ towing 197
Trunk lid closing 40
Trunk lid, emergency unlock‐ ing 41
Trunk lid, hotel function 41
Trunk lid opening 40
Trunk lid via remote con‐ trol 38
Turning circle 206
Turning circle lines, rearview camera 134
Turn signals, operation 69
Turn signals, rear, bulb re‐ placement 191
U
Unintentional alarm 45
Units of measure 92
Universal remote control 144
Unlocking/locking via door lock 39
Unlocking/locking with re‐ mote control 37
Unlocking, settings 42
Updates made after the edito‐ rial deadline 7
Upholstery care 202
USB interface 150
V
V8 high-performance engine, High-performance engine
V8 156
Vanity mirror 146 Vehicle battery 192
Vehicle battery, replac‐ ing 192
Vehicle, break-in 158
Vehicle care 201
Vehicle features and op‐ tions 6
Vehicle identification num‐ ber 9
Vehicle jack 192
Vehicle paint 201
Vehicle storage 203
Vehicle wash 200
Ventilation 142
Ventilation, refer to Parked- car ventilation 143
Venting, see ventilation 142
Vent, see ventilation 142
VIN, see vehicle identification number 9
Voice activation system 26
W Warning and indicator lamps, see Check Control 79
Warning displays, see Check Control 79
Warning messages, see Check Control 79
Warning triangle 195
Warranty 7
Washer fluid 71
Washer nozzles, wind‐ shield 71
Washer system 69
Washing, vehicle 200
Water on roads 160
Weights 206
Welcome lamps during un‐ locking 37
Welcome lights 95
Wheel base, vehicle 206
Wheel cleaner 202
Wheels, changing 176 Wheels, everything on wheels
and tires 172
Wheels, Flat Tire Monitor FTM 106
Wheels, Tire Pressure Moni‐ tor TPM 103
Width, vehicle 206
Window defroster, rear 141
Windows, powered 45
Windshield, climate con‐ trol 159
Windshield washer fluid 71
Windshield washer noz‐ zles 71
Windshield washer sys‐ tem 69
Windshield wiper 69
Winter storage, care 203
Winter tires, suitable tires 177
Winter tires, tread 175
Wiper 69
Wiper blades, replacing 189
Wiper fluid 71
Wiper, fold-out position 71
Wiper system 69
Wood, care 202
Word match concept, naviga‐ tion 24
Wrench, see Onboard vehicle tool kit 189 Seite 216ReferenceEverything from A to Z216
Online Edition for Part no. 01 40 2 959 695 - II/15