2015 AUDI S3 engine

....,
N
0 > co
rl I.O
"' ....,
"' rl
-Do not drive faster than 50 mph (80 km/
h). You r isk having an accident.
- Avoid full-throttle acceleratio n, heavy
braking, and fast cornering . You risk hav­
ing an acc ident.
- Never drive us ing more than one spare
wheel and tire. You risk having an acci­
dent.
- Normal summer or winter tires must not
be mounted on the compact spare whee l
rim.
- For technical reasons, the use of tire
chains on the spare tire is not permitted.
If it is necessary to dr ive with tire chains,
the spare wheel must be mounted on the
front axle in the event of a flat in a rear
t ir e. The newly ava ilable front wheel
must then be i nstalled in pla ce of the
re ar wheel with the f lat tir e. Ins tall ing
the tire chai n befo re mo unting the wheel
and tire is recommended .
- Loose items in the passenger compart­
ment can cause serio us personal inj ury
dur ing hard braking or in an accident.
Never store the inf latable spare tire or
jack and tools in the passenger compart­ ment.
- Norma l summer or winter tires m ust not
be mounted on the compact spare wheel
rim .
Removing the subwoofer
App lies to vehicles : with subwoofer
The subwoofer must be removed before the
spare wheel* can be removed .
Fig. 178 Spa re whee l w ell : subwoo fer
What do I do now ? 269
Removing the subwoofer
.,. Lift the cargo floor¢ page 268, fig . 176.
.,. Pull the latch (D ¢ fig. 178 toward the ca -
ble.
.,. Press the locking tab @down .
.,. Remove the connector ® and set the re-
moved cable as ide .
.,. Remove the bolt @ .
.,. Carefully remove the subwoofer .
Installing the subwoofer
.,. Carefully place the subwoof er n the rim
wel l. The word "FRONT" on the subwoofer
must face forward.
.,. Insert the connector that was removed.
.,. Secure the subwoofer with the bolt .
.,. Fold the cargo floo r cover back into place.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger 's safety when chang ­
ing a wheel .
.,. Aft er you experience a tire failure, pull the
car we ll away from mov ing traffic and try to
reac h
level ground before you stop ¢ &_ .
.,. All passenge rs should
leave the car and
move to a safe location (for instance, behind
the guardrail)¢ &_ .
.,. Engage the
parking brake to prevent your
veh icle from rolling unintentionally¢&_ .
.,. Move
sel ector lever to po sition P ¢ ,&. .
.,. If you are towing a t ra iler, unhi tch the trailer
from your ve hicle .
.,. Take t he
jack ¢ page 268 and the sp a re tire
¢ page 268 out of the luggage com part ­
ment .
A WARNING
You or your passengers could be inj ured
while changing a w heel if you do not fo l­
l ow these safety p recaut io ns:
- If you have a flat tire, move a safe d is­
tance off the road. Turn off the engine,
turn the emergency flashers on and use

272 What do I do now?
hold on to the car to keep your balance
and take care not to slip.
Raising the vehicle
Th e ve hicl e must b e lifted with the jack first
before the wheel can be removed.
Fig. 182 Sill p anels : m arkin gs
Fig. 183 Sill: positio ning t he veh icle jack
.. Engage the parking brake to prevent your
vehicle from rolling unintentionally.
.. Move the
selector lever to position P .
.. Find the marking (imprint) on the sill that is
nearest the wheel that will be changed
~ fig . 182. Behind the marking, there is a
lifting point on the sill for the vehicle jack.
.. Vehicles with a sill : Note the position of the
sill when positioning the vehicle jack
r::!) fig. 183.
.. Place the vehicle jack (vehicle tool kit) on a
firm surface. Use a flat , stable support if
necessary . On a slippery surface such as tile,
you should use a non-slip pad (such as a rub ­
ber mat)
¢ _& .
.. Turn the vehicle jack located under the lift­
ing point on the sill to raise the jack until its
arm @Q
fig. 183 is located under the des­
ignated plastic mount Q
.&., Q (D .
.. Align the jack so that its arm @ Q
fig. 183
engages in the designated lifting point in the door sill and
the movable base @ lies
flat on the ground. The base @ must be
ver­
tical
under the lifting point@ .
.. Wind the jack up further until the flat tire
comes off the ground Q
.&_.
Position the vehicle jack only under the desig­
nated lifting points on the sill
Qfig . 182.
There is exactly one location for each wheel.
The jack must not be positioned at any other location Q
,&q(j) _
An unstable surface under the jack can cause
the vehicle to slip off the jack. Always provide a firm base for the jack on the ground . If nec­
essary place a sturdy board or similar support
under the jack . On
hard, slippery surfaces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping Q
,&.
_& WARNING
- You or your passengers could be injured
while changing a wheel if you do not fol­
low these safety precautions:
- Position the vehicle jack only at the
designated lifting points and align the
jack. Otherwise, the vehicle jack could
slip and cause an injury if it does not
have sufficient hold on the vehicle .
- A soft or unstable surface under the
jack may cause the vehicle to slip off
the jack . Always provide a firm base for
the jack on the ground. If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- Only raise your vehicle with the vehicle
jack provided by the factory. If you use
a vehicle jack for another vehicle, your
vehicle can slide and cause injury.
- Changes in temperature or load can af­
fect the height of the vehicle .
- Never start the engine when the vehi­
cle is raised, which could cause an acci-
dent.
~

2 76 Fuses and bulbs
Fuses and bulbs
Electrical fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through.
Fig. 186 Steering column area: cover
Fig. 187 Left side of the engi ne co mpar tmen t: fuse
cover
Fuses in the interior
The fuses are behind the cover in the steering
column area
¢ fig. 186.
"'Turn off the ignition and the failed electrical
equipment.
"'Check the following table to see which fuse
belongs to the equipmen t
¢page 277.
"'Remove the cover ("AIRBAG" label)
c:> fig. 186. Begin at the bottom right corner
-arrow- .
"' Remove the plastic clip from the fuse panel
cover in the eng ine compartment
c:> fig. 187.
"' Remove the blown fuse using the plast ic
clamp and replace the f use with an ident ica l
new one.
"'Install the cover.
Fuses in the engine compartment
"'Turn off the ignition and the failed electrical
equipment.
"' Check the following table to see which fuse
belongs to the equipment
c::;, page 2 78.
"'Remove the fuse panel cover ¢fig. 187 .
"'Remove the plastic clip from the fuse panel
cover
c:> fig. 187.
"' Remove the blown fuse using the plastic
clamp and replace the fuse with an identical
new one.
The indiv idual circuits are protected by safety
fuses. The fuses are located under the steer­
ing wheel beh ind a cover and in the left side of
the engine compartment .
_&. WARNING
-
Do not repa ir fuses and never replace a
blown fuse with one that has a higher amp
rating. This can cause damage to the elec­
trica l system and a fire.
(D Note
- If there are multip le fuse values in a cell
in the follow tables, for examp le
5/10/20, it is because of equipment-re­
lated differences. Replace the burned
fuse with an identical new one .
-If a new fuse should burn out again
shortly after you have installed it, have
the electrical system checked by your au­
thorized Audi dealer or qualified repair
facility as soon as possible .
(D Tips
- The following table does not list fuse lo­
cations that are not used.
- Some of the following tables on ly apply
to in certain models or options.

....,
N
0 > co
rl I.O
"' ....,
"' rl
Interior fuse assignment
Fig. 188 Vehicle inter ior: fuse assignment
No . Equ ipment
Fl Engine components
F2 Seat adjustment
F 3 Hydraulic pump
cover (Cab-
riolet)
F4 MM controls, MMI-compo-
nents
FS Gateway
F 6 Anti-theft alarm system
Climate/heating control,
se-
lector lever (automatic
F7 transmission), park ing heat-
e r, rear window heater relay
coil
Diagnosis, electrical parking
F 8 brake
switch, light switch,
rain/light sensor, interior
light ing
F9 Steering
column switch
module
Fl0 Disp lay
Fll Reversible driver's
side safe-
ty belt tensioners
Fl2 MMI a rea
No .
Fl 3
Fl4
Fl5
Fl6
Fl7
Fl8
Fl9
F20
F23
F24
F25
Ampere
30 F26
10 F27
40 F28
F29
7.5
F31
s F32
5 F33
10 F34
10 F35
1 F36
5
25 F37
15/20
Fu se s and bulb s 2 77
Equipment Ampere
Adaptive dampers control
20
module
Climate control system 30
blower
Electronic steering column
10
lock
MM I area 7.5
Instrument cluster 5
Rearview camera 7.5
Conv ince key system control
7.5
module, tank system
Tank system 7.5
Ex terior lighting, heated
40
washer fluid nozzles
Panorama sunroof/ power
top control modu le, power 20/30
top latch (Cabriolet)
Door/dr iver's side doors (for
30
example power windows)
Seat heati ng 30
Sound-amplifier 30
Power top con trol module,
5
electron ics (Cabriolet)
Interior lights 7.5
Ex terior lighting
40
Driver assistance systems 7.5
Airbag 5
Button illumination, coils
for upper cab in heat ing relay
(Cabriolet) and socket relay,
7.5
interior sound, back-up ligh t
switch, temperature sensor, o il level sensor
Diagnosis, headlight range
control system, air quality
10
senso r, a utomat ic dimming
rearview mir ror
Right corner ing light/ right
15
LED-headlight
Left corner ing light/ left
15
LED -head light

2 78 Fuses and bulbs
No . Equipment Ampere
Door/front passenger's side
F39 doors (for example, power 30
windows)
F40 Sockets 20
F41 Reversible front passenger·s
25
side safety belt tensioners
F42 Central locking components,
40
windshield washer system
F43 Headlights , light ing 30
F44 all wheel drive
15
F49 Starter, clutch sensor, head-
s light
relay coil
FS3 Rear window defogger
30
The power seats* are protected via
circuit
breakers
that automatically switch on after a
few seconds after the overload has been re­
duced.
@ Tips
Note that the following table was accurate
at the time of print ing and is subject to
change.
Left engine compartment fuse
assignment
Fig. 189 Engine compartment : fuse assignment
No.
Fl
F2
F3
F4
F5
F6
F7
F8
F9
FlO
Fll
Fl2
Fl3
Fl5 Fl6
Fl7
Fl8 Fl9
F20 F22
F23
F24
F3 1
F32
Equipment Ampere
ESC control modu le 40
ESC cont rol module 40
Engine control module (gas-
15/30
oline/diesel)
Engine cooling, engine com-
ponents, auxiliary heater 5/10
coil relay (1+2), secondary
air injection pump relay
Engine components, tank 7.5/10/
system 15
Brake light sensor
5
Engine components, water 7.5/10/
pumps 15
Oxygen sensor 10/15
Engine components, ex-
haust door, glow t ime con-
5/10/20
trol module, SU LEV valve
Fuel injectors, fuel control
15/20
module
Auxiliary heater heating ele-
40
ment2
Auxi lia ry heater heating ele-
40
ment 3
Automatic transmission con- 15/30
trol module
Horn 15
Ignit ion coil 5/20
ESC contro l module, engine
7.5
control module
T ermina l 30 (reference volt-
5
age)
Windshield wipers 30
Horn 10
Terminal SO diagnosis 5
Starter 30
Auxiliary heater heat ing ele-
40
ment 1
Vacuum pump 15
LED headlights 5

M N
0 > co ,...., \!) ..,.,
M ..,., ,....,
@ Tips
Note that the following table was accurate
at the time of pr int ing and is subject to
change.
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace burned out bulbs for you.
It is becoming increas ingly more and more
d ifficult to replace veh icle light bulbs since in
many cases, other parts of the car must first
be removed before you a re able to get to the
bu lb. This app lies especia lly to the light bu lbs
in the front of your car which you can on ly
reach through the engine compartment .
Sheet metal and bulb ho lders can have sha rp
edges that can cause ser ious c uts, and parts
must be co rrectly taken apart and then prop ­
erly put back together to help prevent break­
age of parts and long term damage from wa­
ter that can enter hous ings that have not been
properly resealed.
F or your safety, we recommend that you have
your authorized Audi dealer rep lace any bulbs
for you, since your dealer has the proper tools,
the correct bulbs and the expertise.
G as discha rge l amps (Xenon light s):
Due to the high elect rical voltage, have the
bu lbs rep laced by a qualified technician.
Headlights wi th Xenon light can be identified
by the high voltage sticker .
L ED headlights* requ ire no ma intenance .
Pl ease contact yo ur a uthorized Aud i dealer if a
bu lb needs to be replaced.
A WARNING
Contact with high-voltage components of
the electrica l system and improper re­
placement of gas discharge (Xenon) head­
light bulbs can cause serious personal in­
jury and death .
Fuses and bulb s 2 79
- Xenon bu lbs are pressur ized and can ex­
plode when being changed.
- Changing Xenon lamps requires the spe­
cial tra ining, instructions and equip­
ment.
- On ly an authorized A udi dealer or other
qualified workshop should change the bulbs in gas discharge lamps.
A WARNING
There are parts with sharp edges on the
openings and on the bulb holders that can
cause ser ious cuts .
- If you are uncertain about what to do,
have the work performed by an author­
ized Audi dealer or othe r qualified work­
shop. Ser ious personal inju ry may result
from imprope rly performed wo rk.
(D Tips
- If you still prefer to replace the light
bulbs you rself, be aware that the engine
compartment is a hazardous area to
work in
c:::> page 21 lc:::> &
- It is best to ask your authorized Audi
dealer whenever you need to change a
bulb.
-
•
•
•

280 Emergency situations
Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who
have the necessary tools and equipment to
perform these ope rations.
Starting by pushing or
towing
Q;) Note
Vehicles w ith an automatic transmission
cannot be started by pus hing o r tow ing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
using a
pair of jumpe r cables to start the en­
g ine .
Jumper cables
Use only jumper cables of sufficiently large
cross section to carry the starter current safe­
ly. Refer to the manufacturer's specif ications.
Use only jumper cables with
insulated termi­
na l clamps which are distinctly marked:
plus(+) cable in most cases colored red
minu s(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
inju ry. Follow the instructions below for
safe handling of your veh icle's battery.
- Always shield you r eyes and avoid lean­
ing over the battery whenever possible.
- A discharged battery can freeze at tem­
peratures just be low 32 °F (0 °C). Before connecting a
jumper cable, you must
thaw the frozen battery complete ly, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin . Flush any contacted area with
water immediately .
- Improper use of a booster battery to start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with a low acid level in the battery.
- The vo ltage of the booster battery must
also have a 12-volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery . Use of batteries of d ifferent voltage
or substantially different "Ah" rating
may cause an exp losion and personal in­
jury.
- Never charge a frozen batte ry. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batter ies of different voltage or
substantially different capacity (Ah) rat­
ing may cause an exp losion and injury.
The capacity (Ah) of the booster battery
should not be lower than that of the dis ­
charged battery.
- Before you check anything in the engine
compartment, always read and heed a ll
WARNINGS
¢page 217.
(D Note
-App lying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
contro l units, relays, radio, etc .
- Th ere must be no electrical contact be­
tween the vehicles as otherwise current cou ld already start to f low as soon as the
positive(+) terminals are connected. .,.

....,
N
0 > co
rl I.O
"'
@ Tips
The discharged battery must be pr operly
connected to the vehicle's electrical sys­
tem. When jump starting or charg ing the
battery, never connect the negative
ground cable to the batte ry negative post
because the ba ttery manager system must
be able to detect the battery's state of
charge. Always connec t the negative
g roun d cab le to t he negative ground pos t
of t he battery manager cont ro l unit.
Using jump start cables
Connect the jump start cables in the e xact or ­
der described below .
Fig . 190 Eng ine co mpar tment : connecto rs for jum p
star t cab le s an d a charger
Fig. 1 91 Jump start in g the batte ry w ith anot her ve hi­
cle: @-dra ined battery ,@ -starte r bat tery
The batte ry is located to the left in the eng ine
compartment.
Do not jump start a frozen or
thawed battery
¢ A in Starting with jumper
cables on page
280 ! Replace the battery. The
p rocedu re for connecting jump start cab les
that is descr ibed next is designed to he lp
jump sta rt your ve hicl e.
Vehicle with drained battery:
~ .. Read the following carefully ¢ page 280 rl
Emergency situ ation s 281
.. Set the parking brake and p lace the selector
lever in the P position.
.. Turn the ignition and e lectr ica l equ ipment
off in both vehicles.
Connecting the negati ve terminal (-) to
the negat ive terminal (- ) ( black )
.. To r each the battery term inals, flip the bat­
tery cover cap to the side ¢
fig. 190.
1. Clamp the end of the red jump start cable
to the terminal (!)¢
fig. 191 on the dead
battery @ ¢CI)
in Starting with jumper
cables on page 280 .
2. Clamp the othe r end of the red jump star t
c able to the termin al@ on t he charging
battery @.
Connect NEGATIVE (-) to NEGATIVE (-)
(black )
3. Clamp the blac k end of t he j ump sta rt ca­
ble
preferably at the ground point , or on
the nega tive terminal @ on the charging
batte ry @ .
4. Clamp the other black end of the jump start cab le
onl y on the ground point@
on your vehicle @ ¢CI).
S. Route the jump start cab les so they can­
not get ca ugh t in the moving parts in the
engine compa rtment.
St arting the engine
6. Start the engine in the vehicle giving the
charge and let it run at idle.
7 . Start the eng ine in the vehicle with the
dead battery and wait two to three m i­
nu tes unti l it "runs smoothly".
8.
If t he engine does not s tart: Stop the
st art ing procedure afte r 10 seco nds and
then repeat it afte r approximately 30 sec­
onds.
9 . In the vehicle that is be ing jump started,
switch the heater fan and rear window de ­
froster on to reduce any voltage peaks
t hat may occur when disconnecting the
j u mper cables . The headlights must be
switched off .
10 . Wi th the e ngin es runn ing , remov e th e ca­
bles in
rever se orde r of the way t hey were ..,.