2015 AUDI RS5 CABRIOLET lock

"' N
a: LL co
rl I.O
"' rl
"' rl
Step S: Retracting the power top
compartment cover
Fig. 50 Rear of vehicle: retracting the power top com·
partment cover
O> 0 ,._ ~
"' O> ID
• Raise the rear of the power top and hold it in
place
(D ¢ &. in General information on
page 47.
• Slide the power top compartment cover for­
ward @ until it reaches the end position .
Release the power top.
Step 6: Locking the power top
Fig. 51 Inside of the power top: locking the power top
• Insert the emergency release key into the
opening
¢ page 48, fig. 47.
• Turn the emergency release key clockwise
until it stops to lock the power top.
• Remove the emergency release key and in­
stall the cap in the opening .
@ Tips
Make sure the locking mechanisms are
locked securely .
Power top 49
Step 7: Loosening the headliner
Fig. 52 Rear w indow : loosen ing the right side of the
h ead liner
Fig. 53 Rear window: head liner partially loosened
,._ 0 ,._ ~
"' O> m
Perform the following steps at the rear of the
vehicle on both sides of the power top.
• To loosen the headliner, raise the rear of the
power and pull on the yellow loop
c:> fig. 52
with the emergency release key.
• Continue pulling on the loop to loosen the
headliner around the rear window (approxi­
mately 30 cm)
¢ fig. 53.
Step 8 : Securing the latch
Fig. 54 Rear of the power top: securing the latch
Lock the latch on both sides of the vehicle.

50 Power top
• Pull the power top headline r to the side in
the area by the rear head restraints
¢ fig. 54.
• Insert the short end of the emergency re­
lease lever in the yellow sleeve on the power
top support ¢
fig. 54 .
• Turn the emerge ncy release key in the direc­
t ion of the arrow @ unt il the support is
locked .
• Put the emergency release key away @
¢ page 47, fig . 44.

52 Clear vis ion
@ Tips
- The light sensor* for headlight control is
located in the rear view m irror mount.
You should therefore not apply any st ick­
ers to the windsh ield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted
¢page 52.
- When you remove your key from the igni­
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the driv­
er's door is open .
- In cool or damp weather, the ins ide of
the headlights, turn signals and tail lights can fog over due to the tempera­
ture difference between the inside and
outside. They will clea r shor tly after
switching them on. This does not affect
the service life of the lighting.
- In the even t of a light sensor malfunc­
tion, the driver is no tified in the instru­
ment cluster disp lay¢
page 22.
Turn signals and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher .
Fig. 56 Tu rn s ig na l and hig h beam lever
Turn sign als ¢i ¢
The turn signals activate when you move the
l ever into a turn s ignal pos ition when the ign i­
tion is switched on.
(D -right turn signal
@-left tur n signa l
The turn s ignal blinks three times if you just
tap the lever .
High be ams and headlight flasher [D
Move the lever to the correspon ding posit io n:
@ -high beams on
@ -high beams off or headlight flasher
The indicator light
ii in the instrument cl us­
te r turns on .
Notes on thes e features
-The turn signals on ly wor k w ith the ignition
t ur ned on. The indicator ligh ts
Ct or a in
the instrument cluster also blink.
- After you have turned a co rner, the turn s ig ­
na l switches off au toma tically .
- The
high beam works on ly w hen the head­
lights a re on. The ind icator ligh t
II in the
instrument cluster illuminates when the
high beams are on .
- The
headlight flasher works o nly as long as
you ho ld the lever -even if there a re no
lights switched on . The indicator light
II in
the instrument cluster illuminates when you
use the headlight flasher.
A WARNING
--
Do not use the h igh beam or headlight
flasher if you know that these could blind
oncom ing traffic.
Adjusting exterior lighting
The functions ore selected in the radio or
MMI" .
.,. Select: !CARI function button> Exte rior
light ing .
Or
.,. Select: !CARI function button > Car systems *
control button > Vehicle s etting s> Exterior
lighting .
Coming home (light when leav ing car }*,
Leav ing home (light when unlocking car )*
The coming home function illuminates the
area around the vehicle when the ignition is
switched off and th e dr ive r's door is open ed.
Depend ing on veh icle equ ipment, the function
can be switched on and off or the length of
time the lig hts remain on* can be ad justed . ..,.

"' N
a: LL co
rl I.O
"' rl
"' rl
The leavin g home function i lluminates the
area around the vehicle when unlock ing it.
T his function can be switched on and off.
The
c o ming h om e and lea ving home func­
tions on ly operate when it is dark and the
light switch is in the AUTO posit ion
¢ page 51 , fig. 55.
Auto headlight s*
When the light switch is in the A UTO
¢ page 51 position, the switch-on po int of the
lights can be changed in the automatic driving
light function.
Daytime running lights
USA m odel s:
You can switch the dayt ime run­
ni ng lights
on and o ff .
Canada mod els:
The function cannot be
turned off .
It is activated a utomat ica lly each
time the ignition is switched on.
Travel mode*
T he headlight beam is asymmetrical. This pro­
v ides stronger illum ination on the s ide of the
road on wh ich you are driving .
If you are driv­
i ng in a country that d rives on the opposite
side of the road from your own country, th is
will cause glare for on coming drivers. To pre­
vent glare:
- Trave l mode must be selected in vehicles
with Xenon headlights*.
- In veh icles with halogen headlights, ce rtain
areas of the head light lenses must be cov­
ered with wate rproof adhesive covers that
prevent light from passing thro ugh. For
more informat ion, please see your author ­
i z ed Audi dea ler or author ized repa ir faci lity .
(D Tips
When trave l mode is activated, a display in
the driver information system indicates
this each time you switch the ignit io n on.
Clear vi sion 5 3
Emergency flashers
Fig. 5 7 Center co n sole : em erge ncy flasher sw itc h
The emergency flashers makes other moto­
rists aware that you or your vehicle are in an
emergency situation .
.. Press the switch
Gil ¢ fig. 57 to turn the
emergency flashers on or off .
When the emergency f las hers are on, all four
turn s ignals b link at the same time. The turn
s ignal indicator lights .
1B in the instru ­
ment cluster, as well as the light in the emer­
gency flasher switch ~ blink likewise.
You can indicate a lane change or a tu rn w hen
the emergency flashers are switched on by us­
ing the turn signal lever. The emergency flash­
ers stop temporarily .
T he emergency flashers also work when the
ign it ion is turned off .
T he emergency flashers w ill turn on a utomat i­
ca lly if yo u are in an accident where the airbag
has deployed.
(D Tips
You sho uld turn on the emergency f lashers
when:
- yo u are the last veh icle standing in a t raf ­
fic jam so that any other vehi cles coming
can see you, or whe n
- your vehicle has bro ken down or you are
in an eme rgency s ituation, or when
- yo ur vehicle is be ing towed by a tow
truck or if you are tow ing another vehicle
beh ind you.

58 Clear vis ion
• Se lect : I CAR ! function button > Car sys tems*
control button > S erv ici ng & check s > Wiper
s e rv ice po sition
> O n/ Off .
Removing the wip er blade
• Lift the w indshield w iper arm up from the
windshield.
• Press the locking knob
(D c::> fig . 65 on the
wiper blade . Hold the wiper blade firm ly.
• Remove the wiper blade in the direction of
the arrow.
Attach ing th e wip er blade
• Install the new wiper blade in the retainer
on the wiper arm@ until you hear it click in ­
to place on the wiper arm .
• Place the wiper arm back on the windshield.
• Turn the service position off.
_& WARNING
-
For your safety, you should replace the
w iper blades once or tw ice a year . See your
authorized Audi dealer for rep lacement
blades.
(D Note
- The windshield wiper blades must only
be replaced when in the service position!
Otherwise, you risk damaging the paint
on the hood or the w indshield wiper mo­
tor.
- You should not move yo ur vehicle or
press the w indshie ld w iper lever when
t h e wiper arms are folded away from the
windsh ield. The w indshield w ipers would
move back into the ir original position
and could damage the hood and wind­
shield.
- To he lp prevent damage to the wiper sys­
tem, a lways loosen blades which are fro ­
zen to the windsh ield before operat ing
wipers.
- To he lp prevent damage to wiper blades ,
do not use gasoline, kerosene, pa int
th inner, or othe r solvents on or near the
wiper blades . -
To help prevent damage to the wiper
arms or other components, do not at­
tempt to move the wipers by hand.
(D Tips
- Commercial hot waxes applied by auto­
matic car washes affect the how easily
the glass surface can be cleaned .
- Yo u can also use the service position, for
example, if you want to protect the
windshield from icing by using a cover.
Digital compass
Switching the compass on and off
Applies to vehicles: with digita l compass
The compass direction is shown in the rear­
view mirror .
Fig. 66 Rearv iew mirr or: Digita l compass act ivated
• To swi tch the compass on or off, press and
hold the button @until the compass dis ­
p lay in the mirror
c::> fig . 66 appears or disap­
pears.
T he digita l compass on ly works when t he igni­
tion is o n. The directions are indicated with
abbreviations :
N (north), NE (northeast), E
(east), SE (southeast), S (south), SW (south­
west) ,
W (west), NW (northwest).
(D Tips
To prevent inaccurate compass readings,
do not bring any remote contro ls, e lectr i­
ca l devices or metallic objects near the
mirro r.

"' N
a: LL co
rl I.O
"' rl
"' rl
Center armrest
The center armrest can be adjusted to several
levels .
Fig. 71 Armrest between t he drive r's/front passenger's
seats.
Adjusting the center armrest
.. To adjust the angle, raise the armrest from
the starting position
r=:> fig. 71 detent by de­
tent.
.. To bring the armrest back into the starting
pos ition, raise it out of the top detent and
fold it back down.
The arm rest can slide forward and back .
Head restraints
Front head restraints
Applies to vehicles: with ad justable head restraints
Head restraints that are adjusted according
to body size, along with the seat belt, offer
effective protection.
....
::::=;~~-..:.:::::~ I
Fig . 72 Fro nt seat: adjusting the power head restra int
Adjust the head restraint so the upper edge is
as even as possible with the top of your head.
If that is not possible, try to adjust the head
restra int so that it is as close to this position
as poss ible r=:>
page 63 .
Seats and storage 63
.. To adjust the height of the power head re­
straint*, press the button up/down
<=:> fig. 72.
Refer to <=:> page 115, Proper adjustment of
head restraints
for guidelines on how to ad­
just the height of the front head restraints to
suit the occupant's body size.
A WARNING
- Driving without head restraints or with
head restraints that are not properly ad­
justed increases the risk of serious or fa­
tal neck injury dramat ically.
- Read and heed all WARNINGS
<=:> page 115, Proper adjustment of head
restraints .
@ Tips
-To prevent the head restraints from run­
ning into the headliner, they retract au­
tomatically when moving the seat for­
ward or upward.
- Correctly adjusted head restraints and
safety belts are an extremely effective
combinat ion of safety features.
Seat memory
Description
App lies to vehicles: wit h memo ry function
-
The memory fun ction allows you to quickly
and easily store and recall personal seating
profiles for the driver. The memory function is
operated t hrough the master key and the
memory buttons in the driver's door .
The driver's seating profile is stored and as­
signed to the master key each time the vehicle
is locked. When you open the door, the seat
profile is automatically recalled . If two peop le
use one vehicle, it is recommended that each
person always uses "their own " master key.
Up to 2 seat profiles can be stored in the
memory buttons in the driver's door . Once
they a re stored, these seat profiles can be se-
lected at any time.
IJII,-

64 Seats and storage
In addition to the driver 's seat settings, you
can also store and access the exterior mirror
ad justment settings* using the remote con­
trol key or memory button.
Remote control key
Applies to vehicles: with seat memory
To assign the driver's seat settings to the re­
mote contro l key when locking the vehicle, the
function must be activated in the radio or
MMI*
• Se lect :
I CAR I funct ion button> Seat adj ust ­
ment
> Dri ver's se at > Remote c ontrol k ey >
on .Or
• Se lect :
,..,I Cc-cAc-cRc-, 1 funct ion button > Car system s*
control button > Vehicle setting s > Seats >
Driv er' s s eat > Remot e cont rol key > On .
(D Tips
If you do not want another d river's set­
tings to be assigned to the remote key,
sw itch off the memory function us ing the
rad io or MMI* or the
!ON/OFF I button
c:::>page 64.
Memory buttons
App lies to vehicles: with seat memory
Fig. 73 Driver 's door: memory functio n buttons
The memo ry but tons are located in the dr iv­
e r's door .
Switching the memory function on /off
• Press the ION/O FF I button to switch the
memo ry fu nction on/off. The word
OFF
li ghts up when the memory funct io n is
swit ched off. Seat profi les are neither stored
nor recalled .
Storing a s eat p rofile
• Press the ISET I button. When the word SET
lights up, the memory is ready to store set ­
tings.
• Press a memory button
dII or [Ii) briefly . A
tone confirms that the settings were stored.
Acces sing a seat profile
• If the driver's door is open and the ignition
is switched off, press the memory button.
• If the driver's door is closed or the ignition is
switched on, press and ho ld the memory
button until the seat adjustment is com­
plete .
A WARNING
-For safety reasons ., the seat setting can
only be recalled when the vehicle is sta­
tionary -ot herwise you ris k having an ac­
cident.
- I n an emergency the recall proced ure can
be cancelled by p ressing the
ION/OFF I
sw itch or by tapping the memory bu t­
ton s.
Ashtray
Fig. 7 4 Center console : ashtray
Opening /cl osi ng
• To open the ashtray, slide the cover up
c:::> fig. 74.
• To close the ashtray, press down on the cov­
er.
Emptying the ashtray
• To remove the insert, s lide the latch to the
right
c:::> fig. 74 -arrow- . ..,_

66 Seats and st o rage
- Use only soft cups in the cupholder. Hard
cups and g lasses can ca use in jury in an
accident.
- Never use the cupholder or adapter as an
ashtray -risk of fire.
(D Note
On ly drink containers with lids should be
carried in the cupho lder. Liqu id could sp ill
out and damage your vehicle's e lectronic
equipment or stain the upholstery, etc.
Glove compartment
The glove comportment is illuminated and
can be locked .
Fig . 78 Glove compa rtment
.. To open the glove compartment, pu ll the
hand le in the direct io n of the arrow¢
fig. 78
and swi ng the cover down to open.
.. To close the glove compartment, pus h the
glove compartment lid upward until the lock
engages.
The glove compa rtment can be locked using
the mechanical key¢
page 32.
On the r ight side in the glove compartment is
a holder wi th the key body into which the
emergency key must be cl ipped to be able to
start the vehicle .
A WARNING
To reduce the risk of persona l injury in an
accident or sudden stop, always keep the
glove compartment closed wh ile driving.
Luggage compartment
General information
A WARNING ~
Read and follow the important safety pre-
cautions on ¢
page 118, Stowing lug­
gage.
Enlarging the luggage compartment
The backrests con be folded forward either
separately or together.
F ig . 7 9 Luggage compartment: release lever
Folding th e backrest fo rwar d
.. Pull the release lever in the direction of the
arrow to fold the backrest forward .
Folding th e back res t b ack int o the upright
po sition
.. Fold the backrest back up again until it
latches securely¢ _&..
A WARNING
--The backrest must be securely latched in
position so that no items contained in
the luggage compa rtment can s lide fo r­
ward upon sudden braking.
- Always check whether the la tc h is fully
engaged by pulling the seatback for­
ward.
- Never a llow safety belts to become dam­
a ged by be ing caugh t in door or seat
hardware.
- Torn or frayed safety belts can tear and
d a maged be lt hardware can break i n a
crash. Inspect the belts periodically .