2015 AUDI R8 SPYDER ECO mode

On the road
Speed warning 1 lGJ /laJ You can use speed warning 1 to set the maximum
speed while you are driving. This setting wi ll re ­
main in effect until you turn off the ignition, as­
suming that you have not changed or reset the
setting .
The speed warning symbo l
lDJ/[f] (Canada mod­
els) in the warning
1 display appears when you
exceed the maximum speed. It goes out when
the speed falls below the stored maximum
speed.
The speed warning symbo l will also go out if the
speed
exceeds the stored maximum speed by
more than about
25 mph (40 km/h) for at least
10 seconds. The stored maximum speed is delet­
ed.
Sett ing speed warning 1
¢ page 70.
Speed warning 2 lCl/lDJ Storing warning 2 is recommended if you always
want to be reminded of a certain speed, for ex­
ample when you are trave ling in a country that
has a general maximum speed limit, or if you do
not want to exceed a specified speed for winter
tires.
The speed warning 2 symbol
lCIJ(a1 (Canada
models) appears in the disp lay when you exceed
the stored speed limit. Unlike warning 1, it will
not go out until the vehicle speed drops be low
the stored speed limit.
Sett ing speed warning 2
¢ page 70.
@ Tips
Even though your vehicle is equipped with a
speed warning system, you should still watch
the speedometer to make sure you are not
driving faster than the speed limit.
70
Speed warning 1: setting a speed limit
Warning threshold 1 is set by the button .
Fig. 79 Section of instrument cluster: Set/C hec k button
Storing the maximum speed
.,. Dr ive at the desired maximum speed .
.,. Press the knob butto n
c::> fig. 79 until the sym­
bol appears.
Resetting the maximum speed
.,. Dr ive the vehicle at a speed of at least 3 mph
(5 km/h)
.,. Press the knob for more than 2 seconds .
The speed warning symbol
[IH (USA models)/ (01
(Canada models) w ill appear br iefly in the display
when you release the button to indicate that the
max imum speed has been stored s uccessfu lly.
The maximum speed rema ins stored until it is
changed by pressing the button again briefly or
until it is deleted by a lengthy push on the but­
ton.
Speed warning 2: setting a speed limit
Switches in the wiper arm ore used to operate warning threshold 2 .
~--®
Fig. 80 Controls

.... N
l'­
N "1: .... I.O
"' N
"' ....
To store maximum speed
•Turnoff the ignit ion.
• Briefly press the button in the instrument clus ­
ter
9 page 70, fig. 79. The odometer and the
digital clock are now illuminated.
• Press the button for at least 2 seconds. The cur­
rently stored maximum speed appears in the
display
or the crossed out symbol for warning
threshold 2, if no maximum speed was set pre­
viously.
• Press the function selector sw itch in the wiper
lever @r=>
fig. 80 up or down to change the set
val ue. Values run up or down in steps of 6 mph
(10 km/h).
To delete maximum speed
•Turnoff the ignition .
• Briefly press the button in the instrument clus­
ter
9 page 70, fig. 79 . The odometer and the
digital clock are now illum inated.
• Press the button for at least 2 seconds. The cur­
rently stored maximum speed appears in the
display.
• Press the
iRESETI button in the wiper lever @
r:=> fig. 80 until the crossed out speed warning
symbol for warning threshold 2 appears in the
display.
A few seconds after the adjustment is completed,
the illumination for the odometer and the digital
clock w ill go out.
@ Tips
This warning threshold can also be controlled
through the trip computer
r=> page 23, Navi­
gating the menu.
On the road
Cruise control
Switching the system on
The cruise control system makes it possible to
drive at a constant speed starting at 20 mph (30kmlh).
Fig. 81 Contro l lever with set button
• Pull the lever to position (Dr=> fig . 81 to switch
the system on .
• Drive at the speed you wish to set.
• Press button @to set that speed.
The display may vary depending on the type of
display in your vehicle. The indicator light
(lj;jl)~i~ (US model)/ . (Canadian model) will al­
so light up in the instrument cluster.
A WARNING
--
-Always pay attention to traffic even when
the cruise control is switched on. You are al­
ways responsible for your speed and the dis­
tance between your veh icle and other
veh icles.
- For safety reasons, the cruise control should
not be used in the city, in stop-and -go traf­
fic, on twisting roads and when road condi­
tions are poor (such as ice, fog, gravel,
heavy rain and hydroplaning) -risk of acci­
dent .
- T urn off the cruise control temporarily when
entering turn lanes, highway exit lanes or in
construction zones.
- Please note that inadvertently "resting"
your foot on the accelerator pedal causes
the cruise control not to brake. This is be­
cause the cruise control is overridden by the
driver's acce lerat ion.
71

Parking system
Parking system
Parking system advanced
Introduction
Applies to vehicles: with park ing system advanced
Ll
I
Fig. 89 Parking mode 1: Reverse park ing
F ig. 90 Parking mode 2: Parallel parking
Ll
I
Vehicles with the parking system are equ ipped
with a
rear view camera in addition to the acous­
tic and visual parking system.
You can choose between two modes to help you
when parking your vehicle. Use "parking mode 1"
when parking in a parking space or garage
c:;, fig. 89. If you are going to be parallel parking,
use "parki ng mode 2"
r=;,fig. 90.
80
General Information
Applies to vehicles: with parking system advanced
Fig. 91 View from top: Rearview camera coverage area
-------.. -..
Fig. 92 Side view: Rearv iew camera cove rage area
Sensors in the bumper
Sensors are located in the front and rear bump­
ers. If these detect an obstacle, audible and visu­
al signals warn you . The range at wh ich the sen­
sors begin to measure is approximately:
side 3 ft (0.90 m)
front center 4 ft (1.20 m)
side 2
ft (0.60 m)
rear center 5 .2 ft (1.60 m)
The closer you get to the obstacle, the shorter
the interval between the audible signals . A con­
tinuous tone sounds when the obstacle is less
than approximately 1 foot (0 .30 meters) away.
Do not continue dr iving farther.
If the distance to an obstacle remains constant,
the volume of the distance warning gradually
drops after about four seconds (this does not ap­
ply in the continuous tone range).
Rear view camera coverage area
The rearview camera shows you the area beh ind
your vehicle in the navigation system display. This..,_

Driving Sa fel y
Driving Safely
General notes
Safe driving habits
Please remember -safety first!
This chapter contains important information,
tips, instructions and warnings that you need to
read and observe for your own safety, the safety
of your passengers and others. We have summar­
ized here what you need to know about safety
be lts, airbags, chi ld restraints as well as child
safety. Your safety is for us
priority number 1 . Al­
ways observe the informat ion and warn ings in
t his section - for your own safety as well as for
that of your passengers.
The information i n this section applies to all
model ve rsions of your vehicle . Some of the fea­
t ures des cribed in this sect ion may be standard
equipment on some models, or may be optional
eq uipment on others . If you are not sure, ask
your author ized Audi dealer.
A WARNING
-Make certain that you fo llow the instruc­
t ions and heed the WARNINGS in this Man­
ual. It is in your interest and in the interest
of your passengers .
- Always keep the complete owner's literature
in your Audi when you lend or se ll you r vehi­
cle so that this important information will
always be ava ilable to the driver and passen­
gers.
- Always keep the owner's literature handy so
that you can find it easily if you have ques ­
ti ons.
Safety equipment
The safety features are part of the occupant re­
straint system and work together to help reduce
the risk of injury in a wide variety of occident si t­
uations.
Your safety and the safety of yo ur passengers
should not be left to chance. Advances in tec h­
nology have made a var iety of f eatures av ailable
to help re duce the r isk of inj ury in an accident.
86
The following is a listing o f just a few o f the safe ­
ty features in yo ur Audi:
- sophis tica ted s afety be lts for drive r and a ll pas-
senger sea ting pos itions,
- safety belt p rete nsio ners,
- front airbags,
- knee airbags,
- side airbags in the seats
- adjustab le head restraints,
- adjustab le steering column .
These ind iv idual safety featu res can wor k togeth­
er as a sys tem to he lp pro tect you a nd your pas­
sengers in a wide range of accidents . These fea­
tures cannot work as a system if th ey are not al­
ways proper ly adjusted and prope rly used!
Safety i s everyb ody' s re sponsibilit y!
Important things to do before driving
Safety is everybody's job! Vehicle and occupant
safety always depends on the informed and care­
ful driver.
Fo r you r safety and the safety of your passen­
gers,
before driving always:
.,. Make sure that all lights and signals are operat­
ing correctly .
.,. Make sure that the tire pressu re is co rrect.
.,. Ma ke s ure that all w indows are clean and affo rd
good visibility to the outs ide.
.,. Secure a ll luggage and o ther items caref ully
r=;,page 59 .
.,. Make s ure that nothing can interfere with the
pedals.
.,. Adjust front seat, head restraint and mirrors
correctly for your height.
.,. Instruct passengers to adjust the head re­
straints according to the ir height .
.,. Make su re to use the r ight child restraint cor­
rec tly to p rotect ch ild ren
r=;, page 122, Child
Safety.
.,. Sit p roperly in your seat and ma ke su re that
your passengers do the same
c::> page 56, Gen­
eral recommendations.
.,. Fasten your safety belt and wear it properly. A l­
so instruct your passengers to fasten their safe­
ty belts proper ly
c::> page 95 .

..... N
r-­N "': ..... \!) ..,.,
N ..,., .....
vehicle can damage a part of an airbag system
and prevent that system from working properly
in a co llision.
There are some important things you have to know to make sure that the effectiveness of the
system wi ll not be impaired and that discarded
components do not cause injury or pollute the
environment.
A WARNING
Improper care, servicing and repair proce­
dures can increase the risk of personal injury
and death by prevent ing an a irbag from de­
ploying when needed or dep loying an airbag
unexpectedly:
- Never cover, obstruct, o r change the steer­
ing wheel horn pad or a irbag cover or the in­
strument panel or mod ify them in any way.
- Never attach any objects such as cup holders
or te lephone moun tings to the su rfaces cov­
er ing the airbag units.
- F or cleaning the ho rn pad or instrument
pane l, use only a soft, d ry cloth or one mois­
tened with plain water. Solvents or cleaners
cou ld damage the a irbag cover or change
the stiffness o r strength of the mater ial so
that the airbag cannot dep loy and protect
properly.
- Never repa ir, adjust, or change any parts of
the airbag system.
- All wo rk on the stee ring wheel, inst rument
pane l, front seats or elect rical system (in­
cluding the installation of aud io equipment,
cellu lar telep hones and CB radios, etc.)
must be performed by a qualified technician
who has the train ing and special eq uipment
necessary.
- For any work on the airbag system, we
strongly recommend that you see you r au­
tho rized Aud i dea le r o r qualified workshop.
- Never mod ify the front bumper or parts of
the vehicle body .
- Always make sure that the side airbag can
inflate without inte rfe rence:
- N ever install seat covers or replacement
up ho lstery over the front seatbacks that
Airbag syste m
have not been specif ically approved by
Audi.
- Never use additional seat c ushions that
cover the areas where the side a irbags in­
flate.
- Damage to the orig inal seat cove rs or to
the seam in the area of the side airbag
module must a lways be repaired immedi­
ate ly by an authorized Aud i dealer .
- The airbag system can be activated only
once. After an airbag has inflated, it must
be rep laced by an authorized A udi dealer or
qualified technic ian who has the technical
info rmation, t raining and specia l equipment
necessary.
- The airbag system can be deployed only
once. After an airbag has been deployed, it m ust be replaced w ith new repla cemen t
p ar ts des igned and app roved especially for
your Aud i model version . Replacement of
comp lete airbag systems or airbag compo­
nents must be perfo rmed by qualified wor k­
shops only. Make sure that any airbag serv­
ice action is entered in your Audi Warranty
&
Maintenance book let under AIRBAG RE­
PLACEMENT RECORD.
- For safety reasons in severe accidents, the
alternator and starte r are separated from
the vehicle batte ry w ith a pyrotechnic circuit
interrupter.
- Work on the pyrotechnic circuit interrupt­
er must on ly be performed by a qua lified
dealer - risk of an acc ident!
- If the vehicle or the circuit interr upter is
scrapped, all applicable safety precautions
must be followed.
@ For the sake of the environment
Undeployed airbag modules and pretension ­
ers might be classified as Perchlorate Material
-specia l hand ling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlo­ rate. When the vehicle or parts of the re­
stra int system including airbag modules and
safety belts with pretensioners are scrapped,
a ll applicable laws and regulations must be ..,_
115

Child Safety
the safety belt for the front seat passenge r
measures the tension on the be lt . T he inp ut from
this sensor is then used w ith the weight to "de­
cide", whether there is a child restra int w ith a
t ypical 1 year-old child on the front passenger
seat and whether or not the airbag must be
turned off .
Child restraints and Advanced Airbags
Regardless of the chi ld restraint that you use,
make sure that it has been ce rtified to meet Un it ­
ed States Federal Motor Vehicle Safety Standards
and has been certified by its manufact urer for
use with an airbag. If in exceptional circ umstan­
ces yo u must use it on the front passenger seat,
caref ully read all of the information on child safe­
ty and Advanced Airbags and heed all of the ap­
plicable WARNINGS . Make certain that the child
restraint is correctly recognized by the we ight­
sensing mat ins ide the front passenger seat, that
the front passenger a irbag is tu rned off and that
the airbag status is a lways correctly signaled by
the
PASSENGER AIR BAG OFF light .
Many types and models of c hild restra ints have
been ava ilable ove r the years, new models a re in­
troduced regu larly incorporat ing new and im ­
p roved des igns and o lder models are taken out o f
p rod uction. Child rest raints are not standardized.
Chi ld restraints of the same type typically have
d ifferent weights and sizes and different 'foot­
prints,' the si ze and shape of the bottom of the
child restraint that sits on the seat, when they
are installed on a veh icle seat . These differences
make it v irtually impossible to certify compliance
with the requ irements for advanced ai rbags with
each and eve ry child rest raint that has ever been
sold in the past or will be sold ove r the course of
the useful life of your vehicle.
For this reason, the United States Nat iona l H igh­
way Traffic Safety Admin istration has p ublished a
lis t of specific type , makes and models o f chi ld
restraints that m ust be used to certify comp li­
ance of the Advanced Airbag System in your vehi­
cle with the suppression requirements of Federal Motor Vehicle Safety Standard 208. These chi ld
restraints are:
124
Subpart A - Car b ed child restra ints
Model Manufactured on or
after
Angel Guard Angel September 25, 2007 Ride AA2403FOF
Subpart B -Rear -facing child restraint s
Model Manufactured on or
after
Century SmartFit 4543 December 1, 1999
Cosco Arriva September 25, 2007
22 -013PAW and base
22-999WHO
Evenflo Discovery Adjust December 1, 1999
Right 2 12
E venf lo First Choice 204 December 1, 1999
Graco Infant 8457 December 1, 1999
Graco Snug ride September 25, 2007
Peg Perego Pr imo Viag- September 25, 2007
gio SIP I MUNOOUS
Subpart C - Forward-facing and convertible
child re straint s
Model Manufactured on or
after
Britax Roundabout September 25, 2007
E9L02xx
Cosco Tou riva 025 19 December 1, 1999
Cosco Summit Deluxe September 25, 2007 H igh Back Booster
22 -262
Cosco High Back Booster September 25, 2007
22-209
Evenflo Tribute V September 25, 2007
379xxxx
Evenflo Meda llion 254 December 1, 1999
E venflo Generations September 25, 2007
352xxxx
Graco ComfortSport September 25, 2007
Graco Todd ler Safety
September 25, 200 7
Seat Step 2
Graco Platinum Cargo September 25, 2007

Intelligent technology
Press the I!! button briefly¢ fig. 126 . The II in­
dicator light turns on and Sport control Warn­
ing! Restricted st abilit y appears in the driver in­
formation system d isplay. Driving stability is lim­
ited in sport mode.
Sw itch ing ESC off
Press and hold the
l!I button for three seconds .
The ESC indicator light
fl turns on and Stabil i­
z atio n prog ram off appears in the display. ASR is
also switched off when ESC is sw itched off.
Sw itch ing on
Press the
l!J button again. The message Stabili­
zation progr am on appears briefly in the disp lay .
_& WARNING
You should only sw itch the ESC off if your dr iv­
ing ability and the traffic s ituation allow. This
could increase the risk of slipp ing.
- The stabilizing function is limited in ESC
sport mode. The driving wheels could spin and the vehicle could swerve, especially on
slick or slippery road surfaces.
- There is no vehicle stabilization when ESC is
switched off.
(D Tips
If there is a malfunction in the retractable
rear spo iler* or the A udi magnetic ride*, it
may not be possible to activate ESC sport
mode or normal mode may act ivate aga in au­
tomatically.
Braking
What affects braking efficiency?
New brake pad s
During the f irst 250 miles (400 km), new brake
pads do not possess the ir full braking effect, they
have to be "broken in" first¢.&. . The break- in pe­
riod can be considerab ly longer for vehicles w ith
ceramic b rake roto rs*. You can compensate for
this s light ly reduced b ra ki ng power by push ing
ha rder on the b rake peda l. Avoid heavy braking
loads during the bre ak-in period.
136
Operating conditions and driving habits
The bra kes on today's automobiles a re s till sub­
j ect to wear, depend ing largely on operating con ­
ditions and driving habits ¢& . On vehicles that
a re either driven most ly in stop-and-go city traf­
fic or are driven hard, the brake pads should be
checked by your authorized Aud i dealer more of­
te n tha n specified in the Warranty
& Maint e­
nance bookl et. Failure to have you r brake pads
i nspected can resu lt in reduced b rake pe rform­
ance.
On steep slopes, you shou ld use the braking ef­
fect of the engine . This way, you prevent un nec­
essary wear on the brake system . If you must use
you r brakes, do not hold the bra kes down cont in­
u o usly. Pump the brakes at in tervals.
Operating noise
Noises may occur when braki ng depending on the
speed, braking force and outs ide cond it ions such
as tempera ture and hum idity.
Due to the nature of the materia ls used i n ceram­
i c brake rotors*, noises may become more appa­
r ent at low speeds.
Effect of water and road salt
In certa in situations, for examp le after driv ing
through water , in heavy rain, after overnight con­
densation or after washing your car, the braking
effect can be reduced by moisture or ice on the
brake rotors and brake pads . The brakes must be
dr ied fi rst w ith a few careful b rake app lications.
At higher speeds and with the windsh ield wipers
turned on, the brake pads press against the brake r otors for a short amount of time. This occurs at
r egular intervals without the dr iver not ic ing and
provides fo r be tter brake response time under
wet cond it ions.
The effect iveness of the brakes ca n be red uced
when the v ehicle is d riv en on a salt-cove red road
and the b rakes are no t used. Likewise, you clean
off a ccumula ted salt coating from b rake d iscs
and pads with a few ca utious app lications of the
brake ¢& .
D ue to the ir sur fa ce character istics, cerami c
brake ro tors * absorb moistu re in such co ndi tions . ..,.

-If your skin has come in contact with the en­
gine oil, you must subsequently cleanse it
thoroughly.
0 Note
- The oil level must not be above range
¢ page 159, fig. 137 0-danger of convert­
er or engine damage! Contact an authorized
Audi dealer to draw off oil, if necessary.
- Audi does not recommend the use of oil ad­
ditives. They may damage the engine and
adversely affect your New Vehicle Warranty.
@ For the sake of the environment
- Under no circumstances can the oil come in
contact with the sewage network or the soil.
- Observe and follow legal regu lations when
disposing of empty oil containers.
Adding engine oil~
Applies to vehicles: with S tron ic
0 N
-N
~
"' a,
F ig . 141 Engin e co mp artm en t: cove r on t he engin e oil fi ll­
er neck
Before you check anything in the engine compart ­
ment,
always read and heed all WARNINGS
¢.&. in Working in the engine compartment on
page 155.
.,. Shut the engine off .
.. Remove the design cover, if necessary .
.,. Unscrew the cap
'l=?1 to the engine oil fill ing
hole ¢
fig. 141 .
.. Carefully top off with the appropriate o il
¢page 158.
.. Check the oil level again ¢ page 160.
.. Top off the oil again, if necessary .
.. Slide the oil dipstick in and screw the cap back
on the filling hole.
Chec king and filling
A WARNING
- While topping off, the oil must not come in
contact with hot engine parts -fire hazard!
- The oil filler cap must be properly secured to
prevent oil from being sprayed on the hot
engine and exhaust system when the engine
is running -fire hazard!
- If your skin has come in contact with the en­
g ine oil, you must subsequently cleanse it
thoroughly .
(D Note
-The oil level must not be above range
¢ page 160, fig . 139 0 -danger of convert­
er or eng ine damage! Contact an author ized
Audi dea ler to draw off oil, if necessary.
- Audi does not recommend the use of oil ad­
ditives . They may damage the engine and
adversely affect you r New Vehicle Warranty.
@ For the sake of the environment
- Under no circumstances can the oil come in
contact with the sewage network or the soil.
- Observe and follow legal regulations when
disposing of empty o il containers .
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro­
tects the engine from freezing in the winter.
T he coo ling system is sealed and genera lly re­
quires little attention.
The cooling system has been filled at the factory
with a permanent coolant which does not need to
be changed. The coolant consists of a mixtu re of
specially conditioned wate r and the manufactur­
er's glycol-basedcoolant additive Gl3 antifreeze
with anticorrosion additives (50% for USA mod­ els; 60% for Canadian models). This mixture both
assures the necessary frost protection and pro­
tects metal components in the engine's cooling
system from corrosio n and scaling. It also ra ises
the boiling point of the coolant .
1111-
161