2015 AUDI Q7 turn signal

M N
0 ...J
'SI: ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
Clos ing re ar lid /trunk lid
"' Press the close button in the open rear lid
~ fig. 40. The trun k lid moves to the closed
posit ion by itself and soft close locks it auto­
matically ~&_ .
"' The closing process
is stopp ed immediately
if the close button in the rear lid is pressed
again.
"' By push ing the button again, the rear lid is
opened again .
Setting the rear lid o pen po sition
"' Bring the rear lid into the desired open posi­
t ion. The posit ion can only be stored when
the lid is above a certain height .
"' Press and hold the
~fig . 40 button for at
least four seconds to store the desired open
pos ition.
"'T o set a h igher open position , wait at lea st
five seconds and then carefu lly press the
rear lid upward.
"' Press and ho ld the ~
fig. 40 button again for
at least four seconds and this will store the
new open position.
A WARNING
- Never close the rear lid inattentively or
without checking fi rst . Although the
closing force of the rear lid is lim ited,
yo u can st ill ser iously injure yourself or
others.
- Always ensure that no one is w ith in
range of the rear lid when it is mov ing, in
part icu lar close to the h inges and the up­
per and lowe r edges -fingers or hands
can be p inched.
- T o help p reven t po isonous exha ust gas
from being d rawn into the vehicle, al ­
ways keep the rear lid closed while driv­ ing. Never transport objects larger than
those which fit completely into the lug­
gage area, because then the rear lid can­
not be fully closed .
- Never leave your vehicle unattended es­
pecially with the rear lid left open. A
child could crawl into the car through the
luggage compartment and pull the lid
-
Opening and clo sin g 47
shut, becoming trapped and unable to
get out. To reduce the risk of personal in­
jury, never let ch ildren play in or around
your veh icle . Always keep the rear lid as
well as the vehicle doors closed when not in use .
- If there is a l uggage rack or b icycle rack
mounted on the rear lid, it may not be
ab le to open completely o r an opened
rea r lid may close by itself because of the
ad ded weight. So the open rear lid mus t
be supported or the weigh t must be re ­
moved from the luggage rac k first .
(D Tips
- If the rear lid is open o r not properly
locked when the ign ition is turned on ,
t he door and rear lid warning ~
page 22
appears in the instrument cluster dis­
play.
- The automatic rear lid opening/clos ing
process can be stopped by ho ld ing the
rear lid w ith your hand. The lid can then
be further opened/closed by hand.
- If there is a mechan ica l problem wit h the
automatic rear lid
opening process or
there is an obstruction, the process is
stopped immediately .
- If there is a mechan ica l problem with
au ­
tomatic closing for the rear lid or there
is an obstruction, it ope ns again slightly
r ight away. Check to see why the rear lid
cou ld not be closed before attempting to
close it again .
- If the rear lid on a locked vehicle is un­
locked with the midd le button
c:5 on the
remote key, the rear lid i s automat ically
locked agai n immed iate ly afte r closing.
T his is indicated by the turn signals
blinking .
- T he followin g applies to vehicles equ ip­
ped with the Convenience key* feature: i f
the remote control key is left in the lug­
gage compartment, luggage compart­
ment w ill automatically unlock itself a f­
ter you lock the vehicle. Th is prevents
you from unintentionally lock ing you r
key in the luggage compartment. ...,

58 Openin g and clo sing
LED @ starts to blink (after about 10 sec­
onds) . This procedure clears the standard
codes that were set at the factory and
does
n ot need to be repeated again to
program the other buttons.
3 . Briefly press the button on the roof head ­
liner that you would like to program.
4 . Wait unti l the LED @ beg ins to b link. Pro­
gramming mode is active for 5 minutes.
5 . Move in front of you r veh icle while ho ld­
ing the original remote control for the
system that would like to program to a
button in the roof headliner.
P rogramming the butto n: Part 2 on th e
bump er
6 . Hold the remote control towards the left
headlight and the radiator grille
¢fig. 55.
7. Press and hold the remote control until
the turn signals on your vehicle blink. This
may take up to 30 seconds .
8 . If the emergency flashers blink three
times, the programming was successful.
If the emergency f lashe rs on ly blink one
time , the S minute time limit fo r the pro­
gramming has ended or the programming
was not successfu l. Repeat the program­
ming from the third step, or try changing
the distance to the bumper.
9 . If the garage door or other system does
not open us ing the buttons in the roof
headliner even though the programming
was successful, the system may use a roll ­
ing code instead of a fixed code .
Rolling
cod e programming
must be performed
¢ page 58.
The other two buttons in the roof headliner
can be programmed according to the instruc­
tions above . Beg in with the third step .
Erasin g button p rogramming
The programmed bu ttons cannot be erased
individually . They must all be erased together .
Reprogram the buttons if necessary.
.,. Switch the ignition on.
.,. Press and hold both outer buttons in the
roof headliner until the LED@ starts to
blink (after about 10 seconds).
R eprogrammin g the button s
.,. Switch the ignition on.
.,. To reprogram an individua l button, press
and hold the b utton until the LED@ starts
to blink slowly (after about 20 seconds) . Re­
lease the button immediately . Programming
mode is act ive for 5 minutes .
.,. Continue with the fifth step .
(D Tips
-The required distance between the hand
transm itter and the Homelink module in
the bumper ¢
fig. 55 depends on the
system that you a re programming.
- Depending on the model of the system,
you may need to release the button on
the remote control during p rogramming
and press it again. Hold each position
you try fo r at leas t 15 seconds before
t ry ing another posit ion. Keep the turn
signa ls on your veh icle in view when do ­
ing this .
Rolling code programm ing
Applies to vehicles: with garage door opener (Homelink)
Rolling code programming is also needed for
some systems.
Identifying a rolling code
.,. Press and hold the button in the roof head­
liner that was already prog rammed.
.,. Watch the LE D @ ¢
page 57 , fig . 54. If the
LED blinks quickly, the systems (such as a
garage door) is equipped with a ro lling code.
.,. Program the rolling code as follows:
Activatin g the motor unit in a system
.,. Locate the programming button on the sys­
tem's motor un it . The exact loca tion and
color of the button may vary depending on
the brand of the system .
.,. Press the programming button on the ga­
rage door opener motor unit (this will usual­
ly activate an " indicator" on the motor unit) .
You now have approximately
30 second s to
program the button in the roof head lin er . ..,.

light sensor checked as soon as possible at an
authorized Audi dealer or qualified workshop.
A WARNING
- Daytime running lights and automatic
headlights are only intended to assist
the driver. They do not relieve the driver
of his responsibility to check the head­
lights and to turn them on manually ac­
cording to the current light and visibility
conditions. For example, fog cannot be
detected by the light sensors*. So always
switch on the headlights
~D under these
weather conditions and when driving in
the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists. Always turn on
the headlights so that you can see ahead
and so that others can see your car from
the back.
- Please obey all laws when using the
lighting systems described here.
@ Tips
-With the switch in AUTO front fog lights
and rear fog lights cannot be turned on in addition.
- The light sensor for headlight control is
located in the rear view mirror mount.
You should therefore not apply any stick­
ers to the windshield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted ¢
page 61.
-When you remove your key from the igni­
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the driv­
er's door is open.
- In cool or damp weather, the inside of
the headlights, turn signals and tail
lights can fog over due to the tempera­
ture difference between the inside and
outside. They will clear shortly after
M "' switching them on. This does not affect 0
~ the service life of the lighting.
rl I.O
"' rl
"' rl
Clear vision 61
-In the event of a light sensor malfunc­
tion, the driver is notified in the instru­
ment cluster display¢
page 35.
Adjusting exterior lighting
The functions are set in the MMI.
.,. Select: !CAR ! function button > Systems*
control button > Exterior lighting. Or
.,. Select:
I CAR I function button > Car systems*
control button > Vehicle settings > Exterior
light ing.
Coming home (Lights when leaving car),
Leaving home (Lights when unlocking car)
The coming home function illuminates the
area outside the vehicle when you turn the ig­
nition off and open the driver's door. Depend­
ing on vehicle equipment, the function can be
switched on and off or the length of ti me the lights remain on* can be adjusted .
The leaving home illuminates the area outside
the vehicle when you unlock the vehicle . This
function can be switched on and off .
The Coming home and Leaving home func­
tions only operate when it is dark and the light switch is in the
AUTO position.
Daytime running lights
USA models: The daytime running lights can
be turned on or off using this function.
Canada models: The function cannot be
turned
off. It is activated automatically each
time the ignition is turned on. This menu item is shown "greyed out" .
Front fog lights
Fig. 57 Instrument panel: light switch

M
"' 0 ..J
"". rl I.O
"' rl
"' rl
Emergency flasher
The emergency flasher makes other motorists
aware that you or your vehicle are in an emer­
gency situation.
,r--,a.
-------------------
Fi g. 6 0 Center console: em ergency flasher sw itch
.. Press the sw itch ~ ~ fig. 60 to turn the
emergency flashers on or off .
When the emerge ncy flashe r is on, al l four
turn signals blink at the same time. The t urn
signal indicator lights
11111 in the instru­
ment cluster, as well as the light in the emer­
gency f lasher switch ~ blink likewise.
The emergency flashers will turn on automati­ cally if you are in an accident where the airbag
has dep loyed .
@ Tips
You shou ld tu rn on the emergency flashers
when:
- you are the l ast vehicle st anding in a tr af­
fi c jam so that any other vehicles coming
can see you, or when
- your vehicle h as broken down or yo u are
i n an emergency si tuation, or when
- your vehicle is being towed by a tow
tru ck or if you are towing another vehicle
behind you.
Clear vi sion 63
Turn signal and high beam lever
The lever on the left side of the steering col­
umn is used to operate the turn signals and
the high beam as well as the headlight flash­
er.
t
'
Fi g. 61 Turn signal and high beam lever
The turn signa l and high beam lever has t he
following functions :
Turn signals ¢¢
.. Lift the leve r up a ll the way ~ fig. 61 @to
use t he right turn s ignals, or push the leve r
down all the way@to use t he left tur n sig ­
na ls .
Auto -blink
.. Move the leve r (up or down) just to the point
of resistan ce to use the turn signa ls fo r as
long as you need them, for example w hen
chang ing lanes.
.. Move the lever (up or down) just to the point
of resistance and then release it right away
to make the turn signals blink
three times.
You can use t his feature for example when
chang ing lanes on highways.
H igh beam [D
.. Push the lever forward @ to sw itch on the
high beam .
.. Pull the lever back towards you to switch off
the high beam.
Headlight flasher [D
.. Pull the lever toward the steering wheel@
to use the headlight flasher .
~

64 Clear vision
Notes on the se feature s
- The turn signals only work with the ignition
tu rned on. The indicator lights
II or ii in
the instr ument cluster ¢
page 14 also b link .
- After you have turned a corner, the turn sig -
nal switches off a utomat ically.
- T he
high beam works only when the head­
lights are on. The indicator light
SI in the
instrument cluste r illuminates when the
high beams a re on.
- The
headlight flasher works on ly as long as
yo u hold the leve r - even if there are no
lights turned on . The ind icator light
SI in
the instrument cl uster illum inates when you
use the head light flasher.
A WARNING
Do not use the hig h beam o r headlight
flasher if you know that th ese cou ld blind
oncoming traffic.
Interior lights
Front interior lights
-
The interior ligh ts include reading lights for
bo th the driver and the front passenger .
Fig. 6 2 Headli ner: Fro nt inte rior/read ing lights
@ Interior lights
Press the switch ¢ fig. 62 in the correspond ­
ing position.
0 -Interior lights off
I - Inte rior lights on
If the switch is in the center position, the inte­
rior lighting is controlled automatica lly.
@ Reading lights
T o tur n a read ing light on/off, press the b ut­
ton
t!J .
Rear interior lights
There are reading lights in the rear for the
passengers .
Fig. 63 Head liner: Rear read ing lights
~
--
' ~ '-
Fig . 64 Head liner: Third row read ing light
.. Press one of the switches ~ to turn the
N .., N
.:,
~
::i N -.:,
~
right or left reading light on or off c::;, fig. 63.
For vehicles with thi rd row seating *, the lug ­
gage compartment light can be switched on
and off with the button -M-and used as a read­
ing light
c::;, fig. 64. The rear lid has to be
closed.
The lights in the luggage compartment and in
t h e rear lid switch on and off automatically
when the lid is opened and closed.
@ Tips
If the rear lid remains ope n longer than 10
minutes, the l uggage compartment lights
turn off automatically to prevent the vehi­
cle battery from disc harging .

124 Adaptive cruise control
select information from the trip computer,
navigation system* or adaptive cruise control.
@ Vehicle symbol
@ Distance
© Status
@Vehicle symbol
The vehicle symbol indicates whether the sys­
tem has detected an object traveling in front .
-Vehicle outline: Open road, no vehicle
ahead.
- White vehicle: A vehicle is detected ahead.
-Red vehicle : Request for driver to assume
control.
@ Distance
Using the arrows and scale, you can detect
how far it is to the vehicle in front of you.
- Open road: No arrow appears when the ve­
hicle is on an open road and there is no vehi­
cle ahead.
- Driving in traffic: If a vehicle is detected
ahead, the arrow moves on the scale. The
green area represents the distance set.
When approach ing slow ly, the arrow moves
from the
gray zone to the green zone on the
scale .
-Driver intervention prompt : When ap­
proaching rapidly, the arrow serves as an
early warning signal. If the d istance select­
ed is exceeded or possibly not reached, the
arrow moves into the
red zone on the scale.
In certa in driving situations, you as the driv­
er w ill have to take action
c::> page 126, Driv­
er intervention prompt.
@Status
- The text ACC: Off appears in white letters
when adaptive cruise control is turned off.
- The text
ACC: Standby appears in white let­
ters when the system is turned on but no
desired speed has been set.
- The text
ACC: override appears in white let­
te rs when you exceed the desired speed by
acce lerat ing. - The text
D
ISTANC E! appears in red letters
when the interva l to a vehicle traveling
ahead is too short and you have to slow your
veh icle additionally with the foot brake.
- The text messages
DISTANCE 1 to DIS­
TANCE
4 appear in green letters to indicate
the t ime interval you have set and adapt ive
cruise control is in management mode.
- If the driving program "standard" is re­
placed by "comfort" or "dynam ic" using the
MMI , the above text message is supple­
mented by an appropriate prompt, e.g.
DIS­
TANCE
1 -dyn .
System status indicator
Applies to vehicles : wi th adap tive c ruise contro l
The text messages and symbols shown in this
area of the display are not displayed perma­
nently.
Fig. 140 System status indicator
Time intervals (such as.::::::, ____ .::::::,)
The different symbols for the time intervals
(distance) appear if you change the settings
c::> fig. 140 .
Three white dots ... appear if a setting cannot
be made w ith the operating lever. The follow­
ing are possible reasons
- If you pull the cont ro l lever towards you to
resume speed but no requested speed was
set.
- If you push the lever up to increase (or down
to reduce) speed when no speed has been
set previously.
- If you push the lever up to increase (or down
to red uce) speed and this speed is outs ide
Ill>

M
"' 0 _,
"". rl I.O
"' rl
"' rl
Audi side assist Lane Change Assistant
Description
App lies to vehicles: with side assist
The side assist helps you when changing
lanes .
AUDl Q7
Fig. 150 Rear b umper: Pos it ion of radar sensors (not
v is ib le on outside)
F ig .
15 1 Signal light on the outside mirror -driver 's
s ide
~ -..:, .. (D
Side assist uses radar sensors (not visib le on
outside) ¢
fig. 150 to help the d river check
b lind spots, and see what is happen ing in traf ­
fic beh ind the veh icle
¢ page 132, fig. 153.
Signa l lights are bu ilt into both outside m ir­
r ors ¢
fig. 151 . The signal light on the left
ou tside mirror assists when moving over into
the left lane and the signal light on the r igh t
ou tside mirror assists when moving over in to
the right lane .
The s ignal lig ht comes on to tell yo u that side
assis t has detec ted a vehicle on tha t side and
that t he position of this othe r vehicle shou ld
be taken into account if yo u were to change
l anes. This is called the
informationa l stage
sign al¢ page 133.
The informat ional stage
Aud i side assist 131
signal is designed so that you notice it on ly
when you are looking in the outside mirror.
When yo u activate the turn signal and side as ­
s ist de tects a vehicle in a no table location, the
corresponding signal on the outside mi rror
flashes briefly and brightly several times. Th is
is the
alert stage signal ¢page 133.
Activating and deactivating
Applies to vehicles: wit h side assist
Fi g.
1 52 D river 's doo r: Side assist button
Activating
.,. Press the
¢ fig. 152 button. The indicator on
t he button lights up .
Deactivating
.,. Press the button again. The indicator light
on the button goes ou t.
The system works at speeds faster than
19 mph (30 km/h) .
A WARNING
-Imp roper reliance on the side assist sys­
tem can cause coll is ions and serio us pe r­
sonal injury:
- Never rely on ly on side assist when
changing lanes.
- Always check rear view mirrors to make
su re that it is safe to change lanes.
- Side assist canno t detect all veh icles un­
de r all conditions- danger of accident!
- Side assist canno t detect vehicles in time
to a lert you w hen they app roac h from
behind at very hig h speed, or fall drop
back very qu ickly.
~

132 Audi side assist
-The radar sensor's vision can be reduced
or entirely blocked by rain, snow, and
heavy spray . This can result in side assist
not adequately detecting vehicles or, in
some cases, not detecting them at all.
Always keep an eye on the direction you
are traveling and the relevant area
around the vehicle.
- Please note that side assist indicates
there are approaching vehicles, or
vehicles in your blind spot, only after
your vehicle has reached a driving speed
of at least 19 mph (30 km/h).
- Side assist signal does not work around
tight corners (turning radius less than
328 feet, or 100 m).
- Side assist is no replacement for the driv­
er's full attention. The driver alone is re­
sponsible for lane changes and similar
driving maneuvers. Always keep an eye
on the direction you are traveling and the relevant area around the vehicle.
- To ensure that you do not adversely af­
fect side assist, do not block the area on
the rear bumper where the radar sensors
are located with foreign objects (such as
stickers or bicycle racks).
- Make sure that the signal light on the
outside mirror is not blocked by stickers
or other items.
(Di Tips
- Side assist automatically deactivates if it
detects that the radar sensors are
blocked ¢
page 13 7. The indicator light
on the button goes out .
- The area on the bumper where the radar
sensors are located must consistently re­
main free of snow, ice, and heavy soiling
so that side assist can function properly.
Follow the additional notes on
¢page 138.
-For vehicles with a factory installed tow­
ing hitch* or a trailer hitch* that was in­
stalled later according to factory specifi­
cations, side assist is automatically deac- tivated
as soon as the electrical connec­
tion to the trailer electrical socket is made
¢ page 137.
-For vehicles with a trailer hitch that was
not installed according to factory specifi­
cations, switch off the side assist when
towing a trailer .
- Additional tinting on the front side win­
dows can make it harder to see and cor­
rectly understand the signal light on the
outside mirror.
- For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions¢
page 329.
Sensor detection area
Applies to vehicles: with side assist
-----··· .... ·--·--
@ / ,
--­
ill b''T -
Fig. 153 Sc hematic illustration: Sensor detectio n area
The detection ¢ fig. 153 of the radar sensor
detection area is made up of:
-
- the approach area (light red area) (D, about
230 feet (70 m) behind the vehicle, and
- the "blind spot" (dark red area) @.
The radar sensors cover the adjacent left and
right lanes. Other lanes are
not covered by the
radar sensors.
(D Tips
Side assist does not measure actual lane
width. The system assumes a fixed lane
width . Detection in the left and right lanes
is based on this assumed lane width.
When driving on narrow roads or when
driving to the left or right of the center of
a travel lane, it is possible that vehicles
will be detected that are
not in the lane