2015 AUDI Q3 jack points

M N M N
0 ::i co
rl I.O
"' rl
"' rl
Raising the vehicle
The vehicle must be li~ed with the jack first
before the wheel can be removed .
Fig. 165 S ill pane ls: markings
Fi g. 166 Sill: posit ion ing th e vehicle jack
The location of the jack point is indicated by
a n in den ta ti on on the underside of the vehicle
c::> fig . 165.
"'Activate the parking b rak e to prevent the
vehicle from ro lling u ninten tionally.
"' Move the selector lever to the P position .
"' Find the
markin g (imprint) on the si ll that is
nearest the wheel that w ill be changed
c::>fig. 165 . Behind the marking, there is a
lifting po int on the sill for the vehicle jack .
"' Turn the
vehicle jack located under the lift­
ing point on the sill to raise the jack until
the jaw
c::> fig . 166 @ covers the notch on
the vehicle
c::> .&_ c::>0 .
"'Align the vehi cle jack so the jaw @covers
the notch and the base p late @ is flat on
t h e f loor. The base p late @ must be
vertical
under the lifting point @.
"' Install the rod on the vehicle jack : Insert the
rod into the opening on the handwheel. Turn
the rod left or right to secure it.
"' Continue raising the jack with the rod until
the wheel lifts off the ground slightly .
What do I do now ? 221
Position the vehicle jack only under the desig­
nated lifting po ints on the si ll
c::>fig. 165 .
There is exactly one locat ion for each wheel.
The jack must not be positioned at any other
location
c::> .&. c::> (D .
Soft g round under the jack can cause the ve­
hicle to slip off the jack. A lways p lace the jack
on firm ground. Use a f lat, stable support if
necessary. Use a non-slip surface such as a
rubber mat o n a
slippery surface such as tile.
A WARNING
- You or your passengers co uld be inju red
while changing a wheel if you do not fo l­
low these safety p re ca utions:
- Position the vehicle jack on ly at the
designated lifting points and align the
j ack. Otherw ise, the vehicle jack could
slip and cause an injury if it does not
have sufficient hold on the vehicle.
- Use only the jack* supplied with your
vehicle to raise the veh icle . If you use a
j ac k from a different veh icle, you r vehi­
cle may slip off the jac k -ris k of injury !
- Do not use the jack* supplied with yo ur
vehicle to raise other vehicles, as these
may s lip off the jack -risk of injury!
- A soft o r unstable surface unde r the
j ac k m ay cause the veh icle to slip off
the jack . Always prov ide a fi rm base for
the jack o n the ground.
If necess ary,
u se a st urdy board under the jack.
- On hard, sl ippery su rface (such as t iles)
u se a r ubber mat or s imi lar to prevent
the jack from slipping .
- To help prevent injury to yo urself and
your p asse ngers:
- Do not ra ise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the veh icle and
well away from the road and traffic .
- Make sure jack position is correct, ad­
j ust as necessary and then cont inue to
raise the jack .

222 What do I do now?
-If work has to be done under the vehi ­
cle , ensure that it is safely supported
on suitable stands -risk of injury!
- Never start the engine when the vehi­
cle is on the jack -risk of accident!
CD Note
Do not lift the vehicle by the si ll. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
Taking the wheel off/installing the spare
tire
Follow these instructions step-by-step for
changing the wheel.
Fig. 167 Changing a whee l: u sing the hexago nal socket
(w ith the blade removed) to turn the bolts
Fig. 168 Changing a w hee l: a lignm en t pi n inside the
top hole
After you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, remove and
replace the wheel as follows:
Removing the wheel
> Remove the topmost wheel bolt completely
with the
hexagonal socket in the screwdriv­
er handle (vehicle tool kit)
r=;; fig. 167 and
set it as ide on a
clean su rface. >
Screw the threaded end of the
alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig. 168 .
... Then remove the other whee l bolts as de­
scribed above.
> Takeoff the whee l leaving the alignment pin
in the bolt hole
r=;; (D.
Putting on the spare tire
... Push the spare tire over the alignment pin
¢ CD.
... Screw on the wheel bolts and tighten them
slightly using the hexagonal socket .
> Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly
like the rest.
... Turn the jack handle counter -clockwise to
lower the veh icle until the jack is fully re­
leased .
... Use the wheel bolt wrench to tighten all
wheel bo lts firm ly. Tighten them
in a criss­
cross pattern,
from one bolt to the (approx i­
mately) oppos ite one, to keep the wheel
centered.
> Perform the steps required after changing
the wheel
¢ page 219, After changing a
wheel.
A WARNING
-
Do not use the hexagonal socket in the
screwdriver hand le to tighten the whee l
bolts. It is not possible to tighten the bolts
to the required torque using the hexagonal
socket - risk of accident!
CD Note
When removing or installing the whee l,
the rim cou ld hit the brake rotor and dam­
age the rotor. Work carefu lly and have a
second person to help you.
(D Tips
-When mount ing tires with unidirectional
tread design
make sure the tread pat­
tern is po inted the right way
r=;;page223.
- The wheel bolts shou ld be clean and easy
to turn. Check for dirt and corrosion on

232 Emergency situations
Vehicles with a trailer hitch*
.,. In stall the trailer h itch .
.,. Attach the towing bar or the towing cab le to
the trai ler hitc h.
Unscrew the towing loop agai n after use and
i nsta ll t he
cover in the b umpe r. Re tur n t he
towing loop to t he vehicle too lkit. Be sure to
have the towing loop stored in the vehicle at
a ll t imes.
A WARNING
- If the towing loop is not screwed in as far
as it will go, t he thread can pull out when
the vehicle is towed -potential risk of an
acc ident.
- If your veh icle has
a trailer hitch* on ly
use a specia l towing bar to p revent dam ­
aging the ball h itch . Th ese towing bars
have been specially designed for trailer
t owing hitches.
- If your veh icle has a
trailer hitch* use on­
ly specia l towing cables .
Loading the vehicle onto a flat bed truck
Fig. 17 7 Veh icle on flat bed truck
F ront hook up
.,. Align the vehicle with the centerline of the
car carrier ramp .
.,. Attach the winch hook to the front towline
eye previously insta lled .
Rear hook up
.,. Align the vehicle wit h the centerline of the
car carr ier ramp.
.,. Attach the winch hook to the rear towline
eye previously installed.
(D Tips
Check caref ully to make sure t he hook -up
i s secure before mov ing the car up t he f lat­
b ed truck ramp .
Lifting vehicle
Lifting with workshop hoist and with
floor jack
The vehicle may only be lifted at the lif ting
points illustr ated.
Fig. 17 8 Front lift ing point
Fig . 17 9 Rear liftin g po int
.,. Read and heed WARNI NG c::> .&_ .
.,. Locate lifting points c> fig. 178 and
c>fig. 179 .
.,. Adjust lifting arms of workshop ho ist or
floor jack to matc h ve hicle lift ing po ints .
.,. Insert a rubber pad between the floor jack/
workshop hoist and t he lift ing points .
If you must lift your vehicle with a floor jack
to work undern eath, be su re the vehicle is
safely supported on stand s intended for this
purpo se .
Front lifting point
The lifting poi nt is located on the floor pan re-
i nforcement abo ut at the same level as the
II>

M N
M N
0 ::i co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
jack mounting point ¢ fig. 178. Do not lift
the vehicle at the vertical sill reinforcement.
Rear lifting point
T h e lift ing poin t is lo cate d on th e vertical rein ­
fo rc ement o f the lower s ill for th e on boar d
jack
r::!vfig. 1 79 .
Lifting with vehicle jack
Refe r to ¢ page 221 .
A WARNING
- To reduce the r is k o f se rious injury a nd
vehicle damag e.
- Always lift the ve hicle on ly at the spe­
cial w ork shop h oist and flo or jack lift
points illustrated
¢ fig. 178 and
¢fig. 179 .
-Fai lure to lift the vehicle at these
poi nts cou ld cause the ve hicle to tilt or
fa ll from a lift if the re is a chang e in ve­
h icl e w eigh t distr ibu tion and balance.
This might happen, for e xam ple, w hen
heavy co mpo ne nts su ch as the engi ne
b lo ck or tra nsmi ssion ar e removed .
- W hen removing heavy comp onents like
th ese, a nch or ve hicle to hoist or add cor­
resp ond ing weig hts to maintai n the cen­
ter o f gravity . Othe rwise, the vehicle
mig ht tilt or s lip off the hoist, causi ng
serious persona l injury .
(D Note
- Be aw ar e of t he fo llow ing poin ts be fore
lift ing t he vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission housing, the
front or rear axle or the body side members. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points .
- Before driving over a workshop hoist,
check that the vehicle weight does not
-
Emergency situations 233
exceed the permissible lifting capacity
of the hoist .
- Before driving over a workshop hoist ,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.
•
•