2015 AUDI Q3 check engine

66 On th e road
On the road
Steering
Manually adjustable steering wheel
The steering wheel position is fully adjustable
up and down and forward and bock .
Fig. 73 Lever under the steer ing colu mn
First, adjust the driver's seat correctly .
• Pull the lever
c> fig . 73 <=> &_ .
• Move the steer ing whee l to the desired posi­
t ion.
• Push the lever against the steering column
until it locks.
There must be at least 10 inches (25 cm) be­ tween your chest and the center of the steer­
ing wheel. If you cannot sit more than 10 in­
ches (25 cm) from the steering whee l, see if
adaptive equipment is available to help you reach the pedals and increase the distance
from the steering wheel.
F or detai led information on how to adjust the
driver's seat, see
c> page 51 .
A WARNING
Improper use of steeri ng wheel adjust­
ment and improper seating position can
cause serious personal injury.
- Adjust the steering whee l co lumn on ly
when the veh icle is not moving to pre­
vent loss of veh icle control.
- Adjust the driver's seat or steering wheel
so that there is a minimum of 10 inches
(25 cm) between your chest and the
steering wheel
¢ page 95, fig. 103. If
yo u cannot mainta in this min imum dis- tance, the airbag system cannot protect
you proper ly.
- If physical limitations prevent you from
sitting 10 inches (25 cm) or more from
the steering wheel, check with your au­
thorized Audi dealer to see if adaptive equ ipment is ava ilable .
- If the steer ing wheel is aligned with your
face, the supplementa l driver's a irbag
cannot provide as much protection in an
accident . Always make sure that the
steer ing wheel is aligned with your
chest.
- Always hold the steering wheel w ith your
hands at the 9 o'clock and 3 o'clock posi­
tions to reduce the risk of persona l injury
if the driver's airbag dep loys .
- Never hold the stee ring wheel at the 12
o'clock position or with your hands inside
the steeri ng wheel rim or on the steering
wheel hub . Holding the steering wheel
the wrong way can cause serious injuries
to the hands, arms and head if the driv­
er's airbag deploys.
Ignition lock
Starting engine with the key
Applies to vehicles : w ith ign ition lock
The ignition is switched on and the engine
started with the ignition key .
Fig. 74 Igni tion tock : Igni tion key po siti ons
Switching the ignition on /off
• To switch on the ignition , turn the ignit ion
key to position
(D .
• To switch off the ignit ion, turn the ignition
key to position
@ . ..,.

84 Automatic tr an smis sion
the overload. An indicator lamp mJ illu­
minates and a dr iver message appears
Q page 85 when the clutch is overload­
ed .
- If the engine must remain running, never
have any driving pos ition engaged whe n
checking under the hood . Make sure the
selector lever has securely engaged and is locked in P with the parking brake set
c!:> page 179. Othe rwise, any inc rease in
eng ine speed m ay set the vehicle in mo­
t io n, even wi th the park ing brake ap ­
plied.
(D Note
- When stopping on an i ncl ine, do not try
to hol d the veh icle in place by pressing
the accelerator peda l whi le a driving gear
is selected. This can cause the transmis­
s ion to overheat and can damage it. Acti ­
vate the park ing brake or press the brake
pedal to prevent the vehicle from ro lling .
- Allow ing t he vehicle to roll when the en­
gine is stopped and the selector lever is i n N will damage the transmiss ion be­
cause it is not lub ricated under those cir­
cumstances.
{DI Tips
For safety reasons, the park ing brake is re­
leased automatically only when the dr iv­
er 's safety belt is engaged in the buck le.
Hill descent control
The hill descent control system assists the
driver when driving down declines.
Hill descent control is activated when these­
lector lever is in D/S and you press the brake
pedal. The transmission automatically se lects
a gea r that is suitable for the incline . Hill de­
scent control tries to maintai n the speed ach­
i eved at the time of bra king, within physical
an d techn ic al limita tio ns.
If may still be ne c­
ess ary to adjust the speed with the bra kes . Hill descent contro
l sw itches off once the de ­
cline leve ls out or yo u press the acce lerator
peda l.
On vehicles wi th the cru ise contro l system
Q page 73, hill descent control is also activat ­
ed when the speed is set.
A WARNING
--
Hill descent control cannot overcome
physical lim itations, so it may not be ab le
to maintain a co nstant speed under a ll
conditions. A lways be ready to apply the
b rakes .
Manual shift program
Using the manual shift program you can
manually select gears .
Fig. 88 Center co nsole: s hifti ng t he gears ma nually
Fig . 89 Stee ring w hee l: Shi ft padd les•
Gear selection w ith selector lever
T he t iptronic mode can be selected either w ith
the vehicle stat io nary or on the move .
.,. Push the selector lever to the right from 0/
S. An M appears in the instrument cluster
d isp lay as soon as the transm issio n has
shifted .

M N
M N
0 ::i co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Effect of w ate r and ro ad salt
In certain situa tions, for example after driving
through water, in heavy rain, after overnight
condensation or after washing your car, the braking effect can be reduced by moisture or
ice on the brake rotors and brake pads. The
brakes must be dried first with a few careful
brake applications.
At higher speeds and with the windshield wip ­
ers turned on, the brake pads press against
the brake rotors for a short amount of time.
This occurs at regular intervals w ithout the
driver noticing and provides for better brake response time under wet condit ions.
The effectiveness of the brakes can be reduced
when the vehicle is dr iven o n a salt-covered
road and the brakes are not used . Likewise,
you clean
off accumulated sa lt coating from
brake discs and pads with a few caut ious ap­
p lications of the brake¢.&. -
Cor ro sion
There may be a tendency for dirt to build up
on the b rake pads and corrosion to form on
the discs if the car is not dr iven regular ly or
only for short t rips with little use of the
brakes.
If the brakes are not used frequently, or if cor­ rosion has formed on the discs, it is advisable
to clean
off the pads and discs by b rak ing
fi rm ly a few times from a modera tely high
speed¢ .&..
Faults in the brake system
If you should notice a sudden increase in
brake pedal travel, then one of the two brake
circu its may have failed¢&. -
Low brake fluid le vel
Malfunct ions can occur in the brake system if
the brake fluid level is too low. T he brake fluid
level is monitored electronically .
Brake boo ster
The brake booster increases the pressure that
you generate with the brake pedal. It works
only when the engine is running .¢ .&.
Int ellig ent technolog y 157
Brak e lining we ar status
B rake lining wear may be checked by visual in­
spection o f the condition of the brake pads
thro ugh the openings in the wheel. If neces­
sary, the wheel may be removed for this in­
spection
¢ page 218, Changing a wheel.
A WARNING
-New brake pads don't have the best stop­
ping power and must be "broken-in" dur­
ing the initial 100 to 150 miles (150 to
200 kilometers) of normal c ity dr iving .
You can compensate for this by pressing
the brake pedal more firmly. This also
applies la ter when new pads are instal­
led.
- You should perform braking maneuvers
for the purpose of cleaning the brake
system only if road conditions permit .
Other road users must not be put at risk -
you may cause an accident!
- Before descending a steep grade, reduce
speed and shift transmission into a lower
gea r or lower dr iving range. Do not ride
the brakes or hold the pedal down too
long or too often. This could cause the
brakes to get hot and diminish braking
efficiency.
- Do not "ride the brakes" by rest ing your
foot on the pedal when you do not intend
to brake. This may cause the brakes to overheat, p remature wear and increased
s topping distance.
- Unde r ce rtain cl imati c and ope rat ing
conditions such as passing thro ugh wa­
ter, dr iv ing in heavy rain o r after washing
the vehicle, the effectiveness of the
brakes can be reduced. In winte r, ice can
accumu late on the brake pads, lin ings,
discs and drums. Carefully app ly brakes
for a test. Brakes w ill dry and ice coat­
ings w ill be cleaned
off after a few care­
ful brake applicat ions.
- Driving for an extended period of time on
salt-covered roads without using your brakes can a lso affect braking efficiency.
Clean
off accum ulated salt coating from
•
•

M N
M N
0 ::i co ,...., \!) ..,.,
,...., ..,., ,....,
conditions. Drive especially slow if
offroad with low visibility.
- Please note that the wheels can spin and
the vehicle can break away when the ESC
Offroad Mode is switched off, especially
when the road is slippery.
- Driv ing stability is reduced in the ESC
Offroad mode.
@ For the sake of the envi ronment
Avoid harming the environment and take
nature into consideration .
(D Tips
On ly drive where it is allowed and always
stay on the provided roads and paths .
Driver messages
There is only one right way to drive in difficult
conditions: slowly and with caution!
When driv ing offroad, observe the following:
• Never dr ive the veh icle in terra in which is
not suitable for the veh icle, or wh ich ex­
ceeds your driving skills. Never take any un­
necessary risks!
• Drive slowly and cautiously!
• Pay attention to the
gro und cl earance of
your vehicle! This may vary depending on
the load and composition of the ground and
the environment. The driver is therefore re­
spons ible for deciding whether a vehicle can
handle a specific situation .
• Activate the
ESC-Offr oad-Mode Q page 155
as needed.
• Use the
hill desce nt ass is t Q page 155 when
driv ing down steep sections on hi lls.
Difficult terr ain
Never drive in areas that are not familiar to
you and dr ive slowly when offroad and be pre­
pared and expect the unexpected (e.g . pot­
holes, bou lders, tree stumps, etc.)
To prevent the vehicle from bottoming and
avoid damage to the underbody , you should
drive straight across severe bumps in the
Dri vin g and en vironm ent 165
ground with only one side o f the veh icle so
that only two of your whee ls cross the bumps.
Drive quickly through sandy or marshy offroad
sections and do not stop, if at all possible .
Driving throu gh w ater on road s
Note the following to avoid veh icle damage
when driving through water, for examp le on
flooded roads:
- The water must not be any higher than the
bottom of the vehicle body.
- Do not drive faster than walking speed .
A WARNING
--After driving through water, mud, slush,
etc., the brakes may be slow to take effect because of wet brake rotors and pads. D ry
the bra kes first by braking carefully to re­
store the fu ll braking effect.
(D Note
Vehicle components such as the eng ine,
transmission, suspension or electrical sys­
tem can be severe ly damaged by dr iv ing
th rough water.
(D Tips
- Check the depth of the water before d riv­
ing through it.
- Do not stop the vehicle, drive in reverse
or switch the engine off when driving
thro ugh water.
- Keep i n mind that oncoming veh icles
may create waves that raise the water
level and make it too deep for your vehi­
cle to drive through sa fely.
- Avo id d riving through salt wate r because
i t can cause corros ion.
•
•

M N
M N
0 ::i co ,...., \!) ..,.,
,...., ..,., ,....,
Operating instructions
6"
~ ~
I 1,2 ..
-{ }
l::_
-
2
Fig. 139 Permit ted ball position of the trailer hitch
Trailer towing weights
With a factory-installed or an aftermarket
trailer hitch, the maximum permissible trailer
weight is 2,200 lbs (1,000 kg). The maximum permissible unbraked trailer weight is 1,650
lbs (750 kg) . These specifications apply when
driving on roads having an incline of less than
12%.
Permissible tongue load
For best vehicle handling under these
changed conditions, adjust the trailer load so
that the tongue load is at the maximum al­
lowable or slightly lower . You can get an ap­
proximation of the tongue load with a bath­
room scale or you can measure the load at a
trucking company or weighing station.
With a
factory-installed or an aftermarket
trailer hitch, the maximum permissible load
on the ball hitch may not exceed 220 lbs
(100 kg).
It is recommended to use the maxi­
mum permissible load.
Trailer load distribution
Be sure the load in the trailer is held securely
in place to prevent it from shifting forward,
backward or sideways.
Never allow a passenger to ride in a trailer
¢.&. in Driving instructions on page 168.
Ball mount
The trailer hitch may only be used with suita­
ble ball mount and ball¢
fig. 139. Installa­
tion of the hitch ball must be carried out in ac-
Trailer towing 167
cordance with the manufacturer's instruc­
tions.
Engine cooling system
Towing a trailer makes the engine work hard­
er .
It is important that the cooling system's
performance is up to the additional load.
Make sure that the cooling system has enough
fluid.
Tire pressure
When towing a trailer, inflate the tires of your
vehicle to the cold tire pressure listed under
"Full load" on the tire pressure label. The tire
pressure label is located on the driver's side B­
pillar. Inflate trailer tires to trailer and tire
manufacturers' specifications .
Lights
The headlight settings should be checked with
the trailer attached before driving off. Check
to make sure both vehicle and trailer lights
are working properly.
Safety chains
Be sure trailer safety chains are properly con­
nected from the trailer to the hitch on the ve­
hicle. Leave enough slack in the chains to per­
mit turning corners. When you install safety
chains, make sure they will not drag on the
road when you are driving.
The chains should cross under the trailer
tongue to prevent it from dropping in case of
separation from the hitch.
Driving instructions
Driving with a trailer always requires extra
core and consideration.
To obtain the best possible handling of vehicle
and trailer, please note the following :
.,. Do not tow a loaded trailer when your car it­
self is not loaded.
.,. Be especially careful when passing other
vehicles.
.,. Observe speed limits.
•
•

M N M N
0 ::i co
rl I.O
"' rl
"' rl
Checking and filling Engine hood
Releasing and opening the engine hood
The engine hood is released from inside the
vehicle .
Fig. 1 43 Dr iver's side footwell: eng ine hood release
lever
F ig . 144 Re lease lever un der the engine hood
Make sure the wiper arms are not raised up
from the w indshield. Otherw ise the paint
could be damaged .
.. With the driver's door open, pu ll the lever
under the instrument panel in the direction
of the arrow
c> fig. 143.
.. Raise the hood slightly c> .&,
.. Press the rocker switch under the hood up­
ward
c> fig. 144 . This releases the catch .
.. Open the hood.
A WARNING
Hot engine coo lant can burn you.
- T o reduce the r is k of being burned, never
open the hood if you see or hear steam
or coolan t escaping from the engine
compartment. Wait until no steam or
coolant can be seen or heard be fore care­
fully opening t he hood.
Checkin g and fillin g 179
Closing the engine hood
.. Pull the hood down un til the pressure from
t he stru ts is reduced.
.. Let the hood
drop down and latch in p lace .
Do not try to push it shut; it may fail to en­
gage¢ .&,.
A WARNING
-
A hood that is not completely latched
could fly up and b lock your view while dr iv­
ing.
- When you close the engine hood , check it
to make sure the safety catch has proper­
ly engaged. The hood shou ld be flush
with the surround ing vehicle body parts.
- If you notice while dr iving that the hood
is not secured properly, stop at once and
close it.
Working in the engine compartment
Be especially careful whenever you work in
the engine compartment.
Whene ve r you must pe rform an y wo rk in the
eng ine compa rtment , for e xample check ing
and filling different fluids, there is a risk of
injury , burns and accidents. To prevent per­
so nal injury alway s observe th e foll owing
WARNINGS . Th e engin e compartm ent of an y
v e hicle i s a ha zardou s area
c> .&, .
A WARNING
To help avoid injury, be fore yo u check any­
thing under the hood:
- Tu rn off the engi ne .
- Remove the ignition key.
- Apply the parking brake .
- Move selector leve r of automatic trans-
miss ion to "P" (Park) .
- Always let the engine cool down. Hot
components w ill bur n skin on contact.
- To reduce the risk of being burned, never
open the hood if you see or hear steam
or coo la nt escaping from the eng ine
compa rtment. Wait unt il no steam or

180 Checking and filling
coolant can be seen or heard before
carefully opening the hood.
- Keep children away from the engine com­
partment.
- Never spill fluids on hot engine compo­
nents. They can cause a fire.
- Never touch the radiator fan. The auxili­ ary electric fan is temperature controlled
and can switch on suddenly.
- Never open the coolant reservoir cap
when the engine is still warm. The cool­
ant system is pressurized and hot cool­
ant could spray out .
- Protect your face, hands and arm from
steam or hot engine coolant by placing a
thick rag over the cap when you open the
coolant reservoir .
- Do not remove the engine cover under
any circumstances. This increases the
risk of burns.
- If work on the fuel system or the electri­
cal system is necessary:
- Always disconnect the battery .
- Never smoke or work near heaters or
open flames. Fluids in the engine com­
partment could start a fire.
- Keep an approved fire extinguisher im­
mediately available.
- To avoid electrical shock and personal in­
jury while the engine is running or being
started, never touch:
- Ignition cables
- Other components of the high voltage
electronic ignition system.
- If you must perform a check or repair
with the engine running:
- First, fully apply the parking brake,
move selector lever of automatic trans­
mission to "P" (Park) .
-Always use extreme caution to prevent
clothing, jewelry, or long hair from get- ting caught in the
radiator fan, V-belts
or other moving parts, or from contact­
ing hot parts. Tie back hair before
starting, and do not wear clothing that
will hang or droop into the engine .
- Minimize exposure to emission and
chemical hazards
c> A .
A WARNING
-California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain
or emit chemicals known to the State of
California to cause cancer and birth de­
fects and reproductive harm. In addition,
certain fluids contained in vehicles and
certain products of component wear con­
tain or emit chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm.
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive harms. Wash hands after handling.
(D Note
When adding fluids, always make sure that
they are poured into the proper container
or filler opening, otherwise serious dam­
age to vehicle systems will occur.
@ For the sake of the environment
To detect leaks in time, inspect the vehicle
floor pan from underneath regularly. If
you see spots from oil or other vehicle flu­
ids, have your vehicle inspected by an au­
thorized Audi dealer.

M N M N
0 ::i co
rl I.O
"' rl
"' rl
Checking and fillin g 181
Engine compartment
Engine compartment
These are the most important items that you can check.
Fig. 14 5 Typical layout for containers and engine oil filler cap
(D Coolant expansion tank (- L) . . . 186
@ Engine oil dipstick . . . . . . . . . . . 184
@ Eng ine oi l filler cap ('t::r.) . . . . . 184
@ Brake fl uid reservoir (0)) . . . . . 189
® Jump start point(+) under a cov-
er, ....................... 192, 228
@ Jump start point(-) with hex
head screw, . .. ..... ... .. .. . 192, 228
(J) Windshield washer conta iner
Cw) . . . . . . . . . . . . . . . . . . . . . . 193
The position of the engine o il filling hole
(item @) can differ depending on the engine
des ign .
A WARNING
Before yo u check anything in the engine
compartment, always read and heed all
WARN INGS
~ .& in Working in the engine
compartment on page 179.
-
Engine oil
Engine oil specifications
The engine in your Audi needs the right kind
of oil.
The eng ine in your Audi is a sophisticated
power p lant that was bu ilt to exacting specifi­
cations. This eng ine needs the right k ind of
engine oil that meets specifications regarding
quality and viscosity so that it can run
smooth ly and reliab ly. Choosing the rig ht o il
and changi ng oil within the t ime and mileage
in tervals printed in you r vehicle's Warranty
&
Maintenance booklet matters a lot more to ­
day than it did years ago . Audi has developed
a specia l quality standard for engine oil that
will help assure that your vehicle's engine w ill
get the lubr ication it needs for proper opera-
tion. .,..