2015 AUDI A8 ECU

272 What do I do now?
hold on to the car to keep your balance
and take care not to slip.
AB: Raising the vehicle
The vehicle must be lifted with the jack first
before the wheel can be removed.
Fig. 224 Sill pa nels : m ark ings
Fig. 225 Sill: position ing t he veh icle jack
.. Activate the vehicle jack mode in the MMI:
I CAR ! function button > Car systems control
button>
Servicing & checks> Air susp.:
jack mode
> On.
.. Engage the parking brake to prevent your
vehicle from rolling unintentionally.
.. Move the
selector lever to position P .
.. Find the marking (imprint) on the sill that is
nearest the wheel that will be changed
o
fig. 224. Behind the marking, there is a
lifting point on the sill for the vehicle jack.
.. Turn the
vehicle jack located under the lift­
ing point on the sill to raise the jack until its
arm @o
fig. 225 is located under the des ­
ignated plastic mount o ,& o0 .
.. Align the jack so that its arm @ o
fig. 225
engages in the designated lifting point in
the door sill and the movable base @ lies
flat on the ground. The base @ must be
ver­
tical
under the lifting point @. ..
Wind the jack up further until the flat tire
comes off the ground o
.&,.
Position the vehicle jack only under the desig­
nated lifting points on the sill
c:> fig. 224.
There is exactly one location for each wheel.
The jack must not be positioned at any other
location
c:> .&, c:>Q).
An unstable surface under the jack can cause
the vehicle to slip off the jack. Always provide
a firm base for the jack on the ground. If nec­
essary place a sturdy board or similar support
under the jack. On
hard, slippery surfaces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping
c:> .&,.
A WARNING ~
-You or your passengers could be injured
while changing a wheel if you do not fol­
low these safety precautions:
- Position the vehicle jack only at the
designated lifting points and align the
jack. Otherwise, the vehicle jack could slip and cause an injury if it does not
have sufficient hold on the vehicle.
- A soft or unstable surface under the
jack may cause the vehicle to slip off
the jack . Always provide a firm base for
the jack on the ground. If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic .
- Make sure jack position is correct, ad­
just as necessary and then continue to
raise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.

.... N .... N
0 J:
' "' ....
"' ....
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
(D T ips
The vehicle jack mode switches off auto ­
matically at speeds above 10 km/h.
58: Raising the vehicle
The vehicle must be li~ed with the jack first
before the wheel can be removed.
Fig . 226 S ill pane ls: mark ings
F ig. 227 S ill: posit ion ing the veh icle jack
.. Activate the vehicle jack mode in the MMI:
I CAR I funct ion button > Car syste m s control
button
> Se rvi cing & check s> Air sus p.:
ja ck m ode
> On.
.,. Engage the par kin g brake to prevent your
vehicle from rolling un intentionally.
.. Move the
sel ec tor le ver to po sition P .
.. Find the ma rki ng (imprint) on the sill that is
nearest the wheel that w ill be changed
r=> fig . 226. Behind the marking, there is a
lifti ng po int on the si ll for the vehicle jack.
.. Turn the
ve hicle jack located under the lift­
i ng point on the sill to raise the jack until its
What do I d o now ? 273
arm @r=> fig . 22 7 is located under the des­
ignated plastic mount
r=> A. in AB: Raising
the vehicle on page 272i::>(f).
.. Align the jack so that its arm @c::> fig. 22 7
engages in the designated lifting point in
the door sill and the movable base @ lies
flat o n the ground. The base @ must be
ver­
tical
under the lifting point @.
.. Wi nd the jack up fu rther until the flat t ire
comes off the ground
r=> &,. in AB: Raising
the vehicle on page 272.
Position the vehicle jack only under the desig­
na ted lifting points on the s ill
c::>page 272,
fig. 224 .
There is exact ly one l ocation fo r each
whee l. The jack must not be positioned at any
other location c::>
.&. in AB: Raising the vehicle
on page 2 72r=>
(J).
An un sta ble surf ace unde r the jack can cause
the ve hicle to slip
off the jack . Always provide
a firm base for the jack on the gro und. If nec­
essary place a sturdy board or simi lar support
under the jack. On
h ard , sl ipp ery surf aces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping c::>
,&. .
.&_ WARNING
-You or your passengers cou ld be injured
while changing a wheel if you do not fo l­
low these safety p re cautions:
- Position the vehicle jack on ly at the
designated lifting points and align the
j ack. Otherw ise, the vehicle jack could
slip and cause an injury if it does not
have sufficient hold on the vehicle.
- A soft or unstable surface under the
j ack may cause the veh icle to slip off
the jack . Always provide a firm base for
the jack on the ground .
If necessary,
u se a st urdy board under the jack .
- On hard, slippery surface (such as t iles)
use a rubber mat or similar to prevent
the jack from slipping .
- To help pr event injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged .

,....,
N .... N
0 J:
'SI: .... \!) ..,.,
.... ..,., ....
-Pull the reversible blade from the screw­
driver before you use the hexagonal
socket in the handle to turn the wheel
bolts.
- When mounting tires with
unidirectional
tread design
make sure the tread pat­
tern is pointed the right way
<=>pag e 275.
- The wheel bolts should be clean and easy
to turn. Check for dirt and corrosion on
the mating surfaces of both the wheel
and the hub . Remove all dirt from these
surfaces before remounting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tire with a tread pattern
intended for use in a specific direction, please
note the following:
- The direction of rotation is marked by an ar­
row on the side of the tire.
- If the spare tire has to be installed in the in­
correct direction, use the spare tire only
temporarily since the tire will not be able to
achieve its optimum performance character­
istics with regard to aquaplaning, noise and
wear.
- We recommend that you pay particular at­
tention to this fact during wet weather and
that you adjust your speed to match road
conditions.
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible to restore the handling advantages
of a unidirectional tire.
Notes on wheel changing
Please read the information <=> page 256, New
tires and replacing tires and wheels
if you are
going to use a spare tire which is different
from the tires on your vehicle .
What do I do now? 275
After you change a tire:
-Check the tire pressure on the spare imme­
diately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm).
- If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire, they should be replaced before you
check the tightening torque.
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then, drive with extra care and at re­
duced speeds.
A WARNING
-
- If you are going to equip your vehicle
with tires or rims which differ from those
which were factory installed, then be sure to read the information<=>
page 256,
New tires and replacing tires and
wheels .
-Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com­
partment and are not loose in the pas­
senger compartment .
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the
vehicle.
-Always store damaged wheel, jack and
tools securely in the luggage compart­
ment. Otherwise, in an accident or sud­
den maneuver they could fly forward,
causing injury to passengers in the vehi­
cle. •
•

-When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the eng ine compart­
ment .
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS ¢
page 228.
(D Note
Improper hook-up of jumper cables can r u­
in the generator.
- Always connect POSITIVE( +) to POSI­
TIVE(+), and NEGATIVE(-) to NEGATIVE
( - ) gro und post of the battery manager
control unit .
- Check that all screw plugs on the battery
cells a re screwed in firmly . If not, tighten
pl ugs p rior to connecting clamp on nega ­
tive battery term inal.
- Please note that the procedure f or con­
nect ing a jump er cable as desc ribed
above appl ies spec ifically to the case of
you r vehi cle be ing jump started. When
you are giv ing a jump star t to an othe r ve­
hi cle, do
not connec t the negat ive (-) ca­
ble to the negat ive (-) terminal on the
discharged battery @¢
fig. 236. In ­
stead, securely connect the negative( -)
cable to e ithe r a solid metal component
that is firmly bolted to the engine block
or to the e ng ine block itse lf. If the bat­
te ry tha t is being charged does not vent
to the outside, escaping batte ry gas
could igni te and exp lode!
Emergency towing
with commercial tow truck
General hints
Your Audi requires special handling for tow ­
tng.
The follow ing information is to be used by
commercia l tow tr uck operators who know
h ow to ope rate thei r equipme nt safe ly.
Emergenc y situ ation s 283
-Ne ver tow your Audi. Towing will cause
damage to the engine and tran smission.
- Never wrap the safety chain s or w inch ca­
ble s around the brake lines.
- To prevent unnece ssary damage , your Audi
must be transported with a flat bed tru ck.
- To load the vehicle on to the fl at bed , use
the towing loop found in the vehicle tools
a nd attach to the front or rear anchora ge
¢ page 283 and ¢ page 284 .
_& WARNING
A vehicle being towed is not safe for pas ­
sengers. Never allow anyo ne to ride in a
vehicle be ing towed, for any reason.
Front towing loop
Only install the front towing loop when it is
needed.
Fig. 237 Fr ont bu mpe r: cove r
Fig. 238 Fr ont bu mpe r: sc rew ing in t he tow ing loop
-
The towing loop f its into the threaded hole lo ­
cated on the right s ide of the front bumpe r
and cove red by a sma ll cove r when not in use .
.. Remove the tow ing loop from the vehicle
too l kit .

@ Tips
Check carefully to make sure the hook-up
is secure before moving the car up the flat­
bed truck ramp.
Vehicle transport
Whenever you hove your vehicle transported,
be sure to note the following:
(D Note
Mount the tie-down chains/cables over the
running surface (circumference) of the
tires. Never secure the vehicle by the axle,
the suspension struts or the front or rear
towline eye. For technical reasons, the
pressure in the suspension struts may
change du ring the transport and this will
adve rsely affect vehicle handling.
Lifting vehicle
Lifting with workshop hoist and with
floor jack
The vehicle may only be li~ed at the lifting
points illustrated.
Fi g. 2 42 Front l ift ing po int
Fig. 2 43 Rea r lifti ng point
• Read and heed WARNING Q ,&. .
Emergenc y situ ation s 285
• Activate the vehicle jack mode in the MMI :
!CAR I function button > Ca r system s control
button>
Ser vici ng & ch ecks > Air su sp. :
jack mo de > On .
• Locate lifting points Q fig. 242 and
¢fig. 243.
• Adjust lifting arms of wo rkshop hoist o r
floor jack to match veh icle lifting points.
• Insert a rubber pad be tween the floo r jack/
workshop hoist and the lift ing po ints .
The vehicle jack mode must be activated so
that the automat ic adjustment of the Adap­
tive Ai r Suspens ion does not make it more dif­
fic ult to raise the vehicle with the floor ja ck.
If you mu st l ift your vehicle with a fl oor jack
t o wo rk underneath , be sure the vehi cle i s
s af ely s upported on stand s intended for thi s
purpose.
Front lifting point
The lifting point is located on the floor pan re­
i nforcement about at the same leve l as the
jac k mounting point
Q fig . 242. Do not lift
t h e v ehi cle at the verti cal sill reinf orcement .
Rear lifting point
The lifting point is located o n the vert ical rein ­
forcement of the lower sill for the on-board
jack ¢
fig. 243 .
Lifting with vehicle jack
Refer to ¢ page 2 72 .
&_ WARNING ,-~
-To reduce the risk of serious injury and
vehicle damage .
- Always lift the vehicle only at the spe­
c ia l workshop ho ist and floor jack lift
points illustrated
¢fig . 242 and
¢ fig. 243 .
- Fail ure to lift the vehicle at these
po ints co uld cause the vehicle to tilt or
fall from a lift if there is a change in ve­
hicle weight distribution and balance.
This might happen, for example, when h eavy components such as the eng ine
block or transmission are removed.

,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
complexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, safe ty and e nvir onm en tal con­
cerns p lace very strict limits on the na ture of
repairs and adjustments to engine and trans ­
miss io n pa rts which an owner can perform .
Maintenance, adjustments and repa irs u sua lly
require special tools, testing dev ices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure prope r
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliability
of your vehicle and even void your vehicle war­ ranty. The refo re , proof of servici ng in accord­
ance w ith the maintenance sched ule may be a
condition for upholding a poss ible war ranty
cla im made within the warranty period.
Above all, operational safety can be adversely
affected, crea ting unnecessary risks for you
and your passengers.
If in doubt about any servicing, have it done
by your authorized Audi dealer or any other
properly equipped and q ualified workshop .
We strong ly urge you to give you r a uthorized
Audi dealer the opportun ity to perform all
schedu led maint enance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and t rained spec ialists to keep your vehicle
running properly .
Performing limit ed m aintenance you rself
The following pages describe a limited num­
ber of procedur es which can be performed on
your vehicle with ordinary too ls, should the
need arise and trained personnel be unavaila­
b le. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and carefully follow the instruc­
tions given . Always rigorously obse rve the
WARNINGS provided .
Before you check anything in th e engine
compartment, a lway s re ad and heed all
Con sumer In formation 29 1
WARNINGS ¢ & and¢ & in Working in the
engine comportment on page 228 .
A WARNING
-Ser ious personal injury may occur as a re­
sult of improperly performed mainte­ nance, adjustments or repa irs.
-Always be extremely careful when work­ ing on the vehicle. Always follow com­
mon ly accepted safety pract ices and gen­
eral common sense . Never r isk personal
lnJU ry .
- Do not attempt any of the ma intenance ,
checks or repairs descr ibed on the fol­
lowing pages if you are not fully fam iliar
with these or othe r procedures with re­
spect to t he veh icle, or are uncerta in how
to p roceed .
- Do not do any work without the proper
too ls and equipment. Have the necessary
work done by your authorized A udi deal ­
er or another proper ly equipped and
qualified workshop .
- The engine compartment o f any motor
veh icle is a potentially hazardous area.
Never reach into the area around or
touch the rad iator fan. It is temperature
contro lled and can switch on suddenly -
even when the engine is
off . The radiator
fan switches on automat ically when the
coo lant reaches a certain temperature
and will cont inue to run until the coo lan t
tempera ture drops.
- Always sw itch
off the ignition before any­
one gets under the vehicle.
- Always support your veh icle with safety
stands if it is necessary to work under­ neath the vehicle . The j ack supplied with
the vehicle is not adequate for this pur­
pose and cou ld collapse causing serio us
personal injury .
- I f you must work unde rneath the vehicle
with the wheels on the ground , a lways
make sure the vehicle is on leve l ground,
that the wheels are a lways securely
blocked and that the engine cannot be
started.
•
•

,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
------------------------------~I~ n~ d~ e~x~ 297
Checking
Engin e coolant leve l .... ... .. .. .. .. . 237
r ,re pressure . ... ...... ... .. .. .. .. . 25 1
Ch ild restra ints
Danger o f using ch ild restra ints in the
front seat .. .... .. .... ... .. .. .. ... 153
Where can I get additional information
about child restraints and their use? .. 193
Ch ild restra int system anchors . .. .. .. . 187
Ch ild sa fety .. ............. .... .. ... 174
Convertible locking retractor . . . . . . . . . 184
Guidance fixtures for lower anchorages 189
I mportant safety instructions fo r us ing
child safety seats ......... .. .. .. .. . 177
I mportan t th ings to know when dr iv ing
with chi ldren ... .. .... ... .. .. .. ... 174
Tether anchors
Tether straps
Ch ild safety loc k 191
191
Rear doors (mechan ic al ) ... .. .. .. .. .. 4 1
Rear doors (power) .... ... .. .. .. .. .. 41
Ch ild safety seat
Unused safety belts on the rea r seat . . 179
Ch ild safety seats .......... .... .. .. .
180
Booster seats . . . . . . . . . . . . . . . . . . . . . 182
Convertible ch ild seats ........... .. 181
Convertible locking retractor .. .. .. .. . 184
H ow do I properly install a child safety
seat in my vehicle? ........ .. .. .. .. . 177
I nfant seats . . . . . . . . . . . . . . . . . . . . . . 180
I ns tall ing .. ... .. ..... ... .. .. .. ... 184
Instal ling a chi ld restraint using the
L ATCH system ..... .... ... .. .. .. ... 190
LATCH system ............ .... .. .. . 190
Lower anchorages ........ .. .. .. .. .
Mounting and releasing the anchorage
hook
. . ' . ... ................... . '
188
190
Safety instructions . ..... .. .. .. .. .. . 177
Cleaning 214
Climate con trols . . . . . . . . . . . . . . . . . . . . . 78
Climate control system Supp lementary heater .......... .... . 81
Clock ..... .. .. .. .. .. .... ... .. .. .... 27
C losing
Panorami c sun roof ........ .. .. .. .. .. 44
Sliding/ tilting sun roof .. ... .. .. .. .. .. 43
Sun shade (panoramic sunroof) ... .. .. 45 Co
ld tire inflation pressure ..... ... .. .. 249
Coming home Compact spare tire 48
268
Compartments . . . . . . . . . . . . . . . . . . . . . . 7 4
Compass in the m irror .............. .. S6
Compliance ... .. .... . ... ...... ... .. 293
Consumer Information . . . . . . . . . . 141, 290
Consumption (fuel) ............. .... . 25
Contacting NHT5A
Controls Cleaning
Convenience key . .. ................. . 141
216 35
Starting the engine ................ . 83
Stopping the eng ine (START ENGIN E
STOP button) . . . . . . . . . . . . . . . . . . . . . . 83
Switching the ignition on ............ 83
Un locking and lock ing vehi cle .... .. .. . 35
Convertible child safety seats ....... .. 181
Convertib le locking retractor
Activating ... .... .. . .. .. ..... ... .. 186
Deactivating ..... .. . .. ... .... ... .. 186
Using to secure a child safety seat 1.84, 186
Coolant
refer to E ng ine coolant . ..... ... .. .. 236
Cooler ....... .. .... .......... ...... 76
Cleaning 217
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 76
Cooling mode (automat ic climate control) 79
Cruise contro l
Changing speed ..... .. ..... ... .. .. . 91
Presett ing your speed .......... .... . 91
Switching off .. .. .... .... ....... .. . 91
Switching on . .. .. ...... ........... . 90
( upholder . ... .... .. . .. .. ..... ... .. . 74
Cu rve light ........ .. ..... .......... 108
Cylinder management
refer to Cylinder on demand System . . . 25
Cylinder on demand System ... ... .. .. . 25
D
Data recorde r
Date d isp lay 196
27
Daytime runn ing lights . .. ..... ... .. .. . 46
Decla rat io n of compliance
Adaptive cruise cont rol .... ..... .. .. 293
A udi s ide ass ist .. .. ........... .... 293
•
•

,....,
N ,....,
N
0 J:
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Settings ... .. ........... .. .. .. .... 34
Unlocking and locking vehicle ... .. .. .. 35
Pow er seat adjustment
Front seats . . . . . . . . . . . . . . . . . . . . . . . . S9
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . 61
Power steering
refer to Electromechanical power assist 201
Power windows ............ .... .. .... 41
malfunction ............. .... .. .. .. 42
Pregnant women
Special considerations when wearing a
safety belt . . . . . . . . . . . . . . . . . . . . . . . 148
pre sense .. .. .. ........... .. .. .. .. . 194
Preventative passenger protection . . . . . 194
Programming the Hom elink universa l re-
mote control ................. ... ... 131
Proper occupant seating positions .. .. . 134
Proper safety belt position ... .. .. .. .. . 147
Proper seating position
Front passenger ................... 135
Occupants .. ................. .. ... 134
Rear passengers .......... .. .. .. ... 136
Protecting 216
Q
quattro
refer to All Wheel Drive ............. 202
Question What happens to unbelted occupants? 144
Why safety belts? ............... .. 143
R
Radiator fan ... ........... .. .. .. ... 238
Radio clock .. .. .............. ... .... 27
Rain/light sensor Headlights .............. .... .. .... 46
I ntermittent (windshield wipers) . . . . . . 53
Sensor defective . . . . . . . . . . . . . . . . . . . . 22
RangeffuelleveO .................... 25
Reading lights . ............... ... .... 50
Rear fog lights ............ .... .. .. .. 46
Rear lid
Escape handle
Rear light 266
Defective .. ............. .... .. .... 22
Index 303
Rear seats
Adjusting individual seats ......... .. . 61
Entry assistance . ... .............. .. 64
Front passenger seat adjustment . . . . . . 64
Reclining rear seat .................. 63
Rear view mirror ... .. .............. .. 56
Rear window heating . ................ 80
Recircu lation mode (automatic climate
control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Reclining rear seat ... .............. .. 63
Recuperat ion .. .. .. .. . .. ... .... .... .. 25
Refuelling ... ... .. .. ............... 223
Remote control Garage door opener (HomeLink) ...... 131
Massage function . . . . . . . . . . . . . . . . . . . 64
Unlock ing and locking .............. . 35
Remote luggage compartment lid release 37
Repair manuals .. ................... 290
Repairs Airbag system ..... .............. . 164
Replacing Fuses ......... .. ................. 276
Light bulbs .. .. .. .... ........... .. 280
Tires and wheels ... .............. . 257
Windshield wiper blades ............ . 54
Reporting Safety Defects ............. 141
Request to warm engine by driving Warning/indicator lights ........ .. .. . 21
Reset button . . . . . . . . . . . . . . . . . . . . . . . . 26
Retractor . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Rims Cl eaning ...... .... ............... 215
Roof rack . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Loading ........................... 73
Roof weight . .. .. .... ........... .. . 73
s
SAFE ................... ........... 26
Safe driving habits ... .............. . 133
Safety belt pos ition . . . . . . . . . . . . . . . . . 14 7
Safety belts worn by pregnant women . 148
Safety belt pretensioner . . . . . . . . . . . . . . 149
Serv ice and disposal ... ... .... ..... 150
Safety belt pretensioners Pre sense . . . . . . . . . . . . . . . . . . . . . . . . 194
•
•