2015 AUDI A8 spare wheel

268 What do I do n ow ?
Space-saving spare tire (compact spare
tire)
Applies to vehicles: with space-saving spare tire
The spare tire/wheel is located in the luggage
compartment under the cargo floor cover. It
is intended for short-term use only.
Fig. 219 Spare tire
Tak ing out th e spare tir e
• Lift the cargo floor by the plastic handle
¢fig. 219.
• Hook the handle into the luggage compart­
ment weather strip.
• Turn the large screw¢
fig. 219 counter­
clockwise.
• Takeout the spare tire .
• Always store the vehicle tool kit, the jack*
and the repla ced ti re in the l uggage com­
partment¢
page 139.
• Unhook the cargo f loor before closing the
rear lid.
Using the spare tire (compact spare tir e)
The compact spare tire is on ly intended for
emergenc ies until you can reach a repair shop.
Replace it as quickly as poss ible with a stand­
ard wheel and tire.
There are some restrictions on the use of the compact spare tire. The compact spare t ire
has been des igned specifically for your type of
vehicle.
It must not be swapped with a com­
pact spare tire from another type of vehicle .
Snow chains
Fo r technical reasons, the use of snow chains
on the compa ct spare tire is
not p ermi tte d .
If you do have to dr ive with snow cha ins and a
front tire fails, mount the spare whee l w ith tire instead of a
rear tire. Install the snow
chains on the rear tire and use it to replace
the defect ive front tire.
A WARNING
=
- Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
d icators.
- If the spare tire is more than 6 years old,
use it only in an emergency and with ex­
treme caution and careful driv ing.
- The spare tire is intended only for tem­
porary and short-term use. It should be
replaced as soon as poss ible with the
normal wheel and tire.
-After mounting the compact spare tire, the t ire pressure must be checked as
soon as possible. The tire pressure of the
compact spare t ire must be 4.2 bar; oth­
e rwise, you risk having an acc iden t.
- Do not drive faster than 50 mph (80 km/
h). Yo u ris k having an accident.
- Avoid full-thrott le acceleration, heavy
b rak ing, and fast corne ring. You risk hav­
i n g an accident.
- Neve r drive using more than one spa re
wheel and ti re. You r isk having an acci­
dent.
- Normal summer or win ter t ires must not
be mounted on the compact spare wheel
rim.
- For technical reasons, the use of tire
chains on the spare tire is not permit ted .
If it is necessary to drive with t ire chains,
the spare wheel must be mounted on the
front ax le in the event of a flat in a rear
tire. The new ly available front wheel
must then be installed in place of the
rear whee l with the flat tire. Installing
the t ire chain before mounting the whee l
and tire is recommended.
- Loose items in the passenger compart­ ment can cause se rious personal injury
during hard braking or in an accident. Never store the inflatable spare tire or
jack and tools in the passenger compart­
ment.

.... N .... N
0 J:
- "' ....
"' ....
Spare wheel
Applies to vehicles: with spare wheel
The spare wheel is stored in the wheel well
underneath the floor panel in the luggage
compartment.
F ig. 220 Luggag e co mpartm ent : spar e wh eel
Taking out the sp are whee l
• Lift the cargo floor by the plast ic handle
c:::>fig . 220.
• Hook the hand le into the luggage compart­
ment weather strip .
• Turn the large screw
c:::> fig. 220 counter­
clockwise.
• Takeout the spare tire.
• Always store the vehicle tool kit , the jack*
and the replaced tire in the luggage com­
partment
c:::> page 139 .
• Unhook the ca rgo floor before closing the
rear lid.
& WARNING
-
Loose items in the passenger compart­
ment can cause serious pe rsonal in jury
during hard braking or in an accident.
- Never store the spare wheel or jack and
tools in the passenger compartment.
@ Tips
Check the inflat ion p ressu re of the spare
tire periodically to keep the tire ready for
use.
What do I d o now ? 269
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang ­
ing a wheel.
• After you experience a t ire failure, pull the
car well away from moving traffic and try to
reach
leve l ground before you stop c:::> ,&.
• All passengers should le av e t he ca r and
move to a safe location (for ins tance, behind
t he guardra il)
c:::> ,& .
• Engage the parki ng br ake to prevent your
vehicle from rolling unintentionally
c:::> ,& .
• Move sele ctor lever to po sit ion P c:::> ,&. .
• If you are towing a trailer, unhitch the trailer
from your ve hicle.
• Take the
jac k and the sp are tire out of the
luggage compartment
c:::> page 267,
c:::> page 268 .
& WARNING
You o r you r passengers could be i njured
while changing a wheel if you do not fo l­
low these safety precaut ions:
-I f you have a flat tire, move a safe d is­
tance off the road. Turn off the engine,
turn the eme rgency flashers on and use
other warning devices to a lert other mo­
torists .
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
suddenly and possibly slipping off the
jack, always f ully set the parking brake
and b lock the wheel d iagonally opposite
the wheel be ing changed. When one
front wheel is lifted off the ground, plac­ ing the Automatic Transmission in "P"
(Par k) will
not prevent the vehicle from
mov ing .
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jac k.
-

2 70 What do I do now ?
-Always store the vehicle tool kit, the jack
and the replaced t ire in the luggage com­
partment ¢
page 139.
@ Tips
Before changing the wheel, yo u m ust acti­
vate t he jac king mode, so t hat the auto­
mat ic cont rols fo r the Adaptive Air S us­
pens io n do not make it mo re diff ic u lt to
lift the vehicle with the jack
c.';> page 2 72.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order .
1. Activate the vehicle jack mode
¢page 272.
2. Remove the decorative wheel cover* . For
more deta ils see also
¢ page 270, Deco­
rative wh eel covers
o r ¢ page 2 71 ,
Wheels with wheel bolt caps.
3 . Loosen the wheel bolts ¢ page 2 71.
4. Locate the proper mo unt ing po in t for the
j ack and align t he jack be low tha t poi nt
¢ page 272 or r::!>page 273.
5. Raise the car with the jack¢ page 272 or
¢page 273.
6. Remove the wheel with the flat tire and
then i nstall
the spare ¢page 274.
7. Tighten all wheel bolts ligh tly.
8 .
Lower th e ve hicle w it h the jack .
9 . Use the whee l bolt wren ch and
firmly
tig hte n al l whee l bolts ¢p age 271.
10. Rep lace the decorative wheel cover* .
11. D eactivate t he ve hicle jack mode in the
M MI :
!CARI function button > Car systems
control button > Se rvicing & checks > Air
susp.: jack mode
> Off .
The vehicle jac k mode sw itches off automati ­
cally at speeds above 10 km/h.
A WARNING
Always read and follow all WARNINGS and
informati on
¢ .&. in AB: Raising the vehicle
on page 272
and ¢page 275 .
After changing a wheel
A wheel change is not complete without the
doing the following .
.,. Always store the vehicle tool kit, the jack"
and the rep laced tire in the luggage com­
pa rtment
¢ page 139.
.,. Check the tire pressure on the spare whee l
immed iate ly afte r mounting i t.
.,. As soon as poss ible, h ave the
tightening
torques
on all whee l bolts che cked with a
torque wre nch. The correc t tig hten ing tor ­
que is 90 ft l b (120 Nm).
.,. Have the flat tire
replaced as s oon as possi­
ble.
@ Tips
- If you not ice that the w heel bo lts a re
co rroded and difficult to turn while
chang ing a tire, t hey shou ld be rep laced
before you check the tig htening to rque.
- Dr ive at reduced speed until you have the
t ightening torques checked.
- After changing a whee l, the t ire p ress ure
in all four tires must be chec ked/co rrect ­
ed and the tire p ress ure monito ring in di­
cator must b e sto red in th e MMI
¢ page 265.
' Decorative wheel covers
Applies to vehicles: w ith decorative whee l covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig. 2 21 Cha ngin g a w hee l: Remov ing th e w heel cove r
Removing
.,. Insert the hook (prov ided w ith th e vehicle
t oo l ki t) in the hole in the whee l hub cover . ..,.

274 What do I do now ?
-Passengers must not rema in in the ve­
h icle when it is jacked up.
- Make sure that passengers wait in a
safe p lace away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then continue to
raise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.
CD Note
D o not lift t he vehicle by the si ll. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
@ Tips
The vehicle jack mode switches off auto­ mat ica lly at speeds above
10 km/h.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fi g. 228 Changing a wheel: using the screwdrive r han­
dle (w ith t he blade r emoved) to turn the bo lts
F ig . 2 29 Changing a whee l: a lignmen t pin inside th e
top hole
After yo u have loosened all wheel bo lts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.,. Use the hexagonal soc ket in the scr ewdriv ­
er handle
to completely remove the top­
most whee l bolt and se t it aside on a
clean
surface r=> fig. 228 .
.,. Screw the threaded end of the alignme nt
pin from the tool kit hand-t ight into th e
empty bolt hole
Q fig. 229 .
.,. Then remove the other whee l bolts as de­
scribed above.
.,. Take off the whee l leaving the a lignment pin
in the bo lt ho le r=> 0 .
Putting on the spare wheel
.,. Lift the spare whee l and carefully s lide it
over the alignment p in to g uide it in place
Q0 .
.,. Use the hexagona l socket in th e screwdriver
ha ndle to screw in and tig hten all whee l
bolts
slightly.
.,. Remove the al ignment pin and insert and
tighten the remain ing wheel bolt slightly
like the rest .
.,. Turn the jack hand le counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
.,. Use the wheel bo lt wrench to tighten all
wheel bo lts fi rm ly
r=> page 271 . Tighten
them
crosswise, from o ne bolt to the (ap­
p rox ima tely) opposi te one, to keep the
wheel ce nte red .
CD Note
When remov ing or i nsta lling the whee l,
the rim could hit t he b ra ke ro to r and d am­
age the ro tor. Wor k caref ully and have a
seco nd person hel p you.
(D Tips
Never use the hexagon al socke t in the han­
d le of t he screwdriver to loosen or tighten
the wheel bo lts .
Ill-

,....,
N .... N
0 J:
'SI: .... \!) ..,.,
.... ..,., ....
-Pull the reversible blade from the screw­
driver before you use the hexagonal
socket in the handle to turn the wheel
bolts.
- When mounting tires with
unidirectional
tread design
make sure the tread pat­
tern is pointed the right way
<=>pag e 275.
- The wheel bolts should be clean and easy
to turn. Check for dirt and corrosion on
the mating surfaces of both the wheel
and the hub . Remove all dirt from these
surfaces before remounting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tire with a tread pattern
intended for use in a specific direction, please
note the following:
- The direction of rotation is marked by an ar­
row on the side of the tire.
- If the spare tire has to be installed in the in­
correct direction, use the spare tire only
temporarily since the tire will not be able to
achieve its optimum performance character­
istics with regard to aquaplaning, noise and
wear.
- We recommend that you pay particular at­
tention to this fact during wet weather and
that you adjust your speed to match road
conditions.
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible to restore the handling advantages
of a unidirectional tire.
Notes on wheel changing
Please read the information <=> page 256, New
tires and replacing tires and wheels
if you are
going to use a spare tire which is different
from the tires on your vehicle .
What do I do now? 275
After you change a tire:
-Check the tire pressure on the spare imme­
diately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm).
- If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire, they should be replaced before you
check the tightening torque.
- Replace the flat tire with a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then, drive with extra care and at re­
duced speeds.
A WARNING
-
- If you are going to equip your vehicle
with tires or rims which differ from those
which were factory installed, then be sure to read the information<=>
page 256,
New tires and replacing tires and
wheels .
-Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com­
partment and are not loose in the pas­
senger compartment .
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the
vehicle.
-Always store damaged wheel, jack and
tools securely in the luggage compart­
ment. Otherwise, in an accident or sud­
den maneuver they could fly forward,
causing injury to passengers in the vehi­
cle. •
•

.... N .... N
0 J:
""'. .... I.O
"' ....
"' ....
Technical Data
Vehicle identification
F ig. 2 44 Veh ide Identificat ion Numbe r (VlN) plate: lo ·
c ation on dri ver 's s ide das h pane l
XXXXX XX · X -XXXX XXX
~ fAllftlli. -llllll · NR. ~ W!ru -llllll -NO.
xx
XXXX XXXX XX X XXXXXXXX
XXX XXX
IYP /TYPE
XX XXXXXXX XX X X XX
XXX KW XXX
®i ~W.::·f :l~~ XXXX XXX XXX
©+ ::rw= xxxx I xxxx XXX I xx
M. · AUSSt I IJ'IIDIIS
~--
EOA 7D 5 4UB 6XM SSG SRW
2E H JDZ 1LB lA S 1BA
3FC SMU 7X l
FD A 9G3 OG7 OYH OJF
TL6 3 KA 8EH UlA X98 027
lXW 803 908 824 D2D
7T6 CV7 7KO 4X3 2K2
3L4 4KC 3YO 413 502
1S A 7GB 01A 4GO
XX. X XX X XX X XXXX
Fig. 245
T h e vehicle identification label - inside the
luggage co mpartment
Veh icle Id entifica tion Numb er (VlN )
The Veh icle Iden tifica tion Number is located
in different p laces :
- under the w indshield on the driver's side
~fig. 244.
- i n the MMI: Select: Function button ICAR ! >
Car syste m s> VIN numb er.
- on the vehicle identification label.
V ehicle ident ific ation lab el
The vehicle identification label is located in
the luggage compartment in the spare wheel
well.
Te chni cal Data 28 7
The label ~ fig. 245 shows the fo llowing vehi ­
cle data :
(D Vehicle Ident ifi cat ion Number (V IN)
@ Vehicle type , engine output, transmission
@ Engine and transm ission code
@ Paint number and interior
® Optional equipment numbers
The information of the vehicle identification
label can also be found in your Warranty
&
Maintenance booklet.
Saf ety compliance sticker
T he safety compliance sticker is your assur ­
ance that your new veh icle complies with all
applicable Federa l Motor Vehicle Safety
Standards which were in effect at the time the
vehicle was manufactured. You can find this
sticker on the door jamb on the driver's side.
It shows the month and year of production
and the vehicle ident ificat ion number of your
vehicle (perforat ion) as well as the Gross Veh i­
cle Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
High volt age warning lab el
The high voltage warning label is located in
the engine compartment next to the engine
hood re lease. The spark ign ition system com­
plies with the Canadian standard IC ES-002.
Weights
Gro ss Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
doo r jamb on the driver's s ide.
The Gross Vehicle Weight Rat ing includes the
weight of the bas ic vehicle plus fu ll fuel tank,
o il and coo lant, plus maximum load , which in­
cludes passe nger we igh t (1 50 lbs/68 kg pe r
designated sea ting position) and luggage
weight ~.& -
II>

,....,
N ,....,
N
0 J:
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
-----------------------------~I~n~d~e~x 305
Sliding/tilting sunroof
Emergency closing ................ ..
44
Emergency operation ......... ... .. .. 45
Opening and closing ...... .... .. .... 43
Panoramic sunroof ........ .. .. .. .. ..
44
Snow chains ................. ... ... 261
Sockets . . . . . . . . . . . . . . . . . . . . . . . . 68, 74
Solar operation (automatic climate con -
trol) .. .. ... . .... ............. .. .. .. 81
Sources of information about child re-
straints and their use .......... ... .. . 193
Space-saving spare tire ......... .... .. 268
Spare tire
refer to Compact spare tire . .. .. .. .. . 268
Spare wheel ....................... 269
Speedometer . . . . . . . . . . . . . . . . . . . . . . . 26
Speed rating letter code ..... .. .. .. .. . 257
Speed warning system ...... .. .. .. .. .. 90
Sport differential ............. .... .. 108
Indicator light . . . . . . . . . . . . . . . . . . . . . 23
Start-Stop-System . . . . . . . . . . . . . . . . . . . 87
Engine does not switched off . .. .. .. .. 88
Engine starts automatically .. .. .. .. .. 88
Indicator lights . . . . . . . . . . . . . . . . . . . . 88
Messages . . . . . . . . . . . . . . . . . . . . . . . . . 89
Starting/stopping the engine ... . ... .. 88
switching off/on .......... .. .. .. .. .. 89
START ENGINE STOP button . .. .. .. .. .. 83
Starting from rest . . . . . . . . . . . . . . . . . . . . 86
Start ing off with a trailer .... .. .. .. .. .. 87
Starting the engine 83
Steering
refer to Electromechanical power assist 201
Steering wheel Adjusting steering column ..... ... ... 82
Easy entry feature ........ .. .. .. .. .. 82
I ndicator light . . . . . . . . . . . . . . . . 17,201
Shift paddles ............ .. .. .. .. . 117
Steering wheel heating ....... ... .. .. 81
Steps for determining correct load limit . 254
Stopping the engine . . . . . . . . . . . . . . . . . . 83
Storage ... .. ................. .. .... 74
Sunroof ... ... ............. ...... ... 43
Sun shades Emergency closing (roof) .............
45
Panoramic sunroof ........ .. .. .. .. .. 45 Rear
doors . ..... .. ................ 52
Rear window ... .... ................ 52
Sun visors .. .. .. .. ................. . 51
Symbols
refer to Warning/Indicator lights . .. .. . 11
T
Tachometer . . . . . . . . . . . . . . . . . . . . . 11, 23
T ail lights
Cleaning ...... .. .. ............... 215
TOI clean diesel
refer to Ad Blue ... .. . ... ...... ... .. 225
Technical data . .. .. ................. 287
Technical modifications .............. 293
Temperature display ..... ....... .... .. 23
Tether anchors .. .. .. ............... 191
Tether strap .. .. .. ................. 191
Textiles Cleaning ......... ................ 217
The first 1,000 miles (1,500 km) and after-
wards .... .. .. .. .. .. ............... 205
Tie-downs 70,140
Tips for the environment
Saving fuel ....... ...... ........... 73
tiptronic (automatic transmission) ..... 114
Tire pressure .. .. .. ................ .
Tire pressure monitoring system ..... . .
Loss of air pressure ............... .
Malfunction ... .. .. . .. .... ....... .
Tires
......... .. ...... .............
Service life .. .. .. ............... ..
speed rating letter code ........ ... .
Tire manufacturing date . .......... .
Tire specifications ..... ....... .... .
Tread depth ...... ............... .
Uniform tire quality grading ..... .. . .
Winter tires
. .. ...... ........... ..
Tires and vehicle load limits . .. .... ... .
Tires and wheels Checking tire pressure ............. .
Cold tire inflation pressure ........ . .
Dimensions
.. .. ...... .............
General notes .. .. .. . .. .... ....... .
Glossary of tire and loading terminolo-
gy ...... ... .. .... .......... .... . 251
263
264
264
245
255
257
257
257
255
259
260
253
251
249
256
245
246
Low aspect ratio tires ........... .... 262
•
•