2015 AUDI A6 change wheel

252 Tires and wheels
-Always inflate tires to the
recommended and correct
tire pressure before driving
off .
-Driving with underinflated tires bend more, letting
them get too hot resulting
in tread separation, sudden
tire failure and loss of con­
trol.
-Excessive speed and/over­ loading can cause heat
build-up, sudden tire failure
and loss of control.
-If the tire pressure is too low or too high, the tires
will wear prematurely and the vehicle will not handle
well.
- If the tire is not flat and you
do not have to change a
wheel immediately, drive at
reduced speed to the near­
est service station to check
the tire pressure and add air
as required.
@ Note
Driving without valve stem
caps can cause damage to
the tire valves. To prevent
this, always make sure that
factory installed valve stem caps on all
wheels are secure­
ly mounted on the valve.
@) For the sake of the environment
Underinflated tires will also
increase the fuel consump­
tion.
Tires and vehicle load limits
There are limits to the amount of load or weight that any vehi­
cle and any tire can carry. Ave ­
hicle that is overloaded will not
handle well and is more diffi­
cult to stop. Overloading can not only lead to loss of vehicle
control, but can also damage
important parts of the vehicle
and can lead to sudden tire fail­
ure, including a blowout and
sudden deflation that can cause
the vehicle to crash.
Your safety and that of your
passengers also depends on
making sure that load limits are
not exceeded. Vehicle load in­
cludes everybody and every­
thing in and on the vehicle.
These load limits are technical­
ly referred to as the vehicle's
Gross Vehicle Weight Rating
("GVWR "). .,..

268 Tires and wheels
Tire pressure indicator appears
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
Fig. 200 Display : und erinflatio n warn ing
Fig. 201 Display: Syste m malfunction
Using the ABS sensors , the tire pressure moni­
toring system compares the tire tread circum­
ference and vibration characteristics of the in­
dividual tires.
If the pressure decreases in one
or more tires, this is indicated in the instru­
ment cluster with a warning symbol
[9] and a
message ¢
fig. 200.
The tire pressure monitoring system must be
reset via MMI each time the pressures are ad­
justed (e. g. when switching between partial
and full load pressure) or after changing or re­
placing a tire on your vehicle¢
page 269 . The
TPMS indicator only monitors the tire pres­
sure that you have previously stored. You can
find the recommended tire pressures for your vehicle on the label on driver's side 8-pillar
¢page 244.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the tire pressure in one or more tires is too
low, -
the tire has structural damage,
- th e tire pressure was changed, wheels rotat-
ed or replaced but the TPMS was not reset
¢page 269.
- the spare tire* is mounted .
Warning symbols
[9] Loss of pressure in at least one tire¢&. .
Check the tire or tires and replace or repair if
necessary. The indicator light
[9] in the instru­
ment cluster also illuminates
¢page 12.
Check/correct the pressures of all four tires
and reset TPMS via MMI.
Ill (Tire Pressure Monitoring System ) Tire
pressure! System malfunction . Iflll appears
after switching the ignition on or while driving
¢
fig. 201 and the indicator light [9] in the in­
strument cluster blinks for approximately one
minute and then stays on, there is a system
malfunction . Attempt to store the correct tire
pressure ¢
page 269. If the indicator light
does not turn off or if it turns on shortly
thereafter, immediately drive your vehicle to
an authorized Audi dealer or authorized repair
facility to have the malfunction corrected.
A WARNING
- If the tire pressure indicator appears in
the instrument cluster display, one or
more of your tires is significantly under­
inflated. Reduce your speed immediately
and avoid any hard steering or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures. In­
flate the tire pressure to the proper pres ­
sure as indicated on the vehicle's tire
pressure label¢
page 244 . Driving on a
significantly under-inflated tire causes
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability.
- The driver is responsible for maintaining the correct tire pressures. You must
check the tire pressures regularly. ..,

M N
0 <.J 'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-Under certain cond itions (such as a spor­
ty driving style, w inter condit ions or un­
paved roads), the pressure monitor
indicator may be delayed.
- Ask your author ized Audi dealer if run­
flat tires may be used on your veh icle.
- The tire pressure monitoring system may
stop working when there is an ESC mal­
funct ion.
- Using snow chains may result in a system
malfunction.
- The tire pressure monitoring system on
your Audi was developed using t ires with
the "AO" or "RO" identification on the
tire sidewall
c> page 257. We recom­
mend using these t ires.
Reset tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset via
MMI.
"' Before storing the new tire pressures, check
that the current pressures on all four t ires
correspond to the specified values and
adapt the p ress ures to the current load
c> page 244.
"'Switch on the ignition.
"' Se lect in the MMI:
!CAR ! func tion button>
(Car )* sys tems contro l button > Servicin g &
checks > Tire pre ssure mon ito ring > Store
tire pre ssure s> Y es, sto re now .
Do not store the tire p ress ure if the re a re
snow chains on the tire. Otherwise, a sys­
tem ma lf u nction may occu r.
Tires an d wheel s 269
•
•

M N
0 <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
A WARNING 1=
You or your passengers could be injured
while changing a wheel if you do not fol­
low these safety precautions:
- If you have a flat tire, move a safe dis­
tance off the road. Turn off the engine,
turn the emergency flashers on and use
other warning devices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
suddenly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed. When one
front wheel is lifted off the ground, plac­
ing the Automatic Transmission in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
¢ page 132.
{!) Tips
Before changing the wheel, you must acti­
vate the jacking mode, so that the auto­ matic controls for the Adaptive Air Sus­
pension* do not make it more difficult to
lift the vehicle with the jack¢
page 2 75.
Changing a wheel
When you change a wheel, follow the se ­
quence described below step-by-step and in
exactly that order .
1. Activate the vehicle jack mode*
c::;. page 275.
-
2. Remove the decorative wheel cover* . For
more details see also
¢page 274, Deco­
rative wheel covers
or ¢ page 2 7 4,
Wheels with wheel bolt caps.
3. Loosen the wheel bolts¢ page 274.
What do I do now? 273
4.
5.
6.
7.
8.
9.
Locate the proper mounting point for the
jack and align the jack below that point
¢page 275.
Raise the car with the jack ¢page 275.
Remove the wheel with the flat tire and
then install
the spare <=> page 2 76.
Tighten all wheel bolts lightly.
Lower the vehicle with the jack .
Use the wheel bolt wrench and
firmly
tighten all wheel bolts¢ page 274 .
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode* in the
MMI:
ICARI function button > (Car)* sys­
tems
control button > Servicing & checks
> Air susp.: jack mode > Off .
The vehicle jack mode* switches off automati­
cally at speeds above 6 mph (10 km/h).
A WARNING
Always read and follow all WARNINGS and information<=>
A in Raising the vehicle on
page 275
and <=> page 277.
After changing a wheel
A wheel change is not complete without the
doing the following.
.,. Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment
c::;. page 132.
.,. Check the tire pressure on the spare wheel
immediately after mounting it.
.,. As soon as possible, have the
tightening
torques
on all wheel bolts checked with a
torque wrench. The correct tightening tor­
que is
90 ft lb (120 Nm) .
.,. Have the flat tire
replaced as soon as possi­
ble.
(D Tips
- If you notice that the wheel bolts are
corroded and difficult to turn while
changing a tire, they should be replaced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked.
ll>
•
•

M N
0 I.J "". rl I.O
"' rl
"' rl
-Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury.
@ Tips
- Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bolts.
- If a wheel bolt is very tight, you may find
it easier to loosen by carefully push ing
down on the end of the wheel bolt
wrench with
one foot only. As you do so,
hold on to the car to keep your ba lance
and take care not to slip.
Raising the vehicle
The vehicle must be lifted with the jock first
before the wheel con be removed .
Fig. 209 Sill pane ls: markings
'ii
9
--~~ :;:~:'.'"'-i
Fi g. 210 Sill: posit ion ing th e ve hicle jack
~ Activate the vehicle jack mode* in the M MI:
I CAR I funct ion button> ( C ar)* s ystem s con­
t rol button >
Servicing & c heck s > Air susp.:
jack mode
> On .
~ Engage the parking bra ke to prevent your
vehicle from rol ling un intentionally.
~ Move the selector le ver to position P.
What do I d o now ? 275
~ Fi nd the marking (imprint) on the sill that is
nearest the whee l that will be changed
r::!) fig. 209. Beh ind the marking, there is a
lift ing point on the sill for the veh icle jack.
~ Vehicles w ith a sill: remove the cover from
the sill before lift ing the veh icle with a vehi­
cle jack
r::!) page 2 76.
~ Tu rn the v ehicle ja ck located under the lift­
ing point on the sill to ra ise the jack unt il its
a rm @<::!)
fig. 210 is lo cated under the des­
ig nated p lastic moun t
r::!) .&, r::!)(D,
~ Align the jack so that its arm@ r::::> fig. 210
engages in the designated lifting point i n
the door s ill and the movable base ® lies
flat on the ground. The base @ must be
ver­
tical
under the lifting point @.
~ Wind the jack up further until the flat t ire
comes off the ground
r::!) & .
Position the vehicle jack only under the desig­
nated lifting points on the sill
Q fig . 209 .
There is exactly one locat ion for each wheel.
The jack must not be positioned at any other lo c a ti o n
r::!) A r::!) An un stable surface under the jack can cause
the vehicle to slip off the jack . Always provide
a fi rm base for the jack on the g ro und . If nec­
essary p lace a sturdy board or sim ila r support
u nder the jack. On
hard , slippery surfaces
(such as tiles) use a rubbe r mat or similar to
prevent the jack from slipping
r::!) & .
&_ WARNING
-You or your passengers co uld be in ju red
while changing a whee l if you do not fo l­
low t hese safety preca utions:
- Position the vehicle jack on ly at the
d esigna ted lifti ng points and align the
j a ck . O therw ise, the vehicle ja ck could
s lip and cause an injury i f it does not
have sufficient hold on the vehicle.
- A soft or uns table surface unde r the
j ack may cause the ve hicle to slip off
the jack. A lways provide a firm base for
the jack on the ground . If necessary,
use a st urdy boa rd under the jack.
~

276 What do I do now?
-On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you a re
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to raise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode* switches off auto­ matically at speeds above 6 mph (10 km/
h).
Removing and installing the sill cover
Applies to vehicles: with sill
Fig . 211 Sill: remov ing t he cover
.. Pull the cover down to remove it¢ fig . 211.
.,. To install the cover again , insert it into the
retainers and then swing it upward until it
clicks into place. The cover must be flush
with the sill.
(D Tips
Some models may also have a cover for the
rear vehicle lift point.
Taking the wheel off /installing the spare
Follow these instructions st ep-by-step for
changing the wheel.
Fig. 212 Changing a wheel: using the screwdrive r han­
dle (w it h th e blade re m oved) to turn the bolt s
Fig. 213 Changing a wheel: alignment p in ins ide t he
top hole
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal socket in the screwdriv­
er handle
to completely remove the top­
most wheel bolt and set it aside on a
clean
surface ¢ fig. 212 .
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig . 213 .
.,. Then remove the other wheel bolts as de­
scribed above .
.. Take off the wheel leaving the alignment pin
in the bolt hole
¢(D . Ill>

M N
0 <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Putting on the spare wheel
"'Lift the spare wheel and ca refully slide it
over the alignment pin to guide it in place
¢ (D .
"' Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
"' Remove the alignment pin and insert and
t ighten the remaining wheel bolt s lightly
like the rest .
"'T urn the jack handle counte r-clockw ise to
lower the vehicle unt il the jac k is f ully re­
l eased .
"' Use the whee l bolt wrench to tighten a ll
whee l bolts firmly
¢ page 274. Tighten
them
crosswis e, from one bolt to the (ap­
proximate ly) opposite one, to keep the
wheel cen tered.
When removing or install ing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you .
{D) Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or t ighten
the wheel bolts .
- Pull the reversib le blade from the screw­
driver before you use the hexagonal
socket in the handle to turn the whee l
bo lts.
- When mounting tires with
un id ire ctional
tread design
make s ure the tread pat­
tern is poi nted the right way
¢ page 277.
- The wheel bolts should be clean and easy
to tu rn . Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the h ub. Remove a ll dir t from these
su rfaces before remo unting the wheel.
What do I do now? 277
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Usi ng a spa re ti re with a tre ad patte rn
intended for use in a specific direction
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection, please
note the following :
- The d irect ion of rotation is marked by an ar­
row on t he side of the ti re .
- If the spare tire has to be installed in the in­
correct direct ion, use the spare tire only
temporarily s ince the t ire will not be able to
achieve its optimum performance cha racte r­
istics w it h regard to aquap la ni ng, no ise and
wear .
- We recommend that you pay part icu lar at­
ten tion to th is fact during we t wea ther and
t ha t you adjust your speed to match road
conditions .
- Replace the fl at t ire wi th a new one and
have i t installed on your vehicle as soon as
possible to restore the hand ling advantages
of a un idirectional tire .
Notes on wheel changing
Please read the information¢ page 257, New
tires and replacing tires and wheels
if you a re
go ing to use a spare tire wh ich is different
from the tires on you r vehicle .
After you change a tire:
- Check the tire pre ssure on the spare imme­
diately after installation.
- Have the wheel bolt tightening torqu e
checked with a torque wrench as soon a s
possible by your authorized Audi dealer or
a qualified service station.
- With steel and alloy wheel rims , the wheel
bolts are cor re ctly tightened at a torque of
90 ft lb (120 Nm ).
- If you notice that the wheel bolts are cor­
roded and diff icult to turn while changing
a tire , they should be replaced before you
check the t ightening torque. .,,.
•
•

M N
0 <.J 'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-----------------------------~I~ n~d~ e~x 303
K
Key ... .... .. .. .... .. .... ... .. .. .... 31
Battery rep lacement master key ... .. .. 32
Emergency key . . . . . . . . . . . . . . . . . . . . . 31
Key not recognized . . . . . . . . . . . . . . . . . . 76
Key replacement . . . . . . . . . . . . . . . . . . . 31
Master key . . . . . . . . . . . . . . . . . . . . . . . . 31
Mechanical key . . . . . . . . . . . . . . . . . . . . . 32
Kick-down tiptronic
K . b nee air ags . ............. .. .. .. .. .
D escr ipt ion .... .. ..... ... .. .. .. .. .
How they work . ... .... ... .. .. .. .. . 111
16 2
162 163
Important safety instructions ... .. .. . 164
L
Lane assist . . . . . . . . . . . . . . . . . . . . . . . . . 93
L ane Change Ass istant
refer to side assist . . . . . . . . . . . . . . . . . . 96
LATCH
.... .. ............. .... .. ... 185
Descr ipt ion . .... ......... .... .. .. . 186
Instal ling a child restraint .. .. .. .. .. . 187
L ocat ion . ............ ...... .... .. 186
M ounting and releasing the ancho rage
hook .. .. .. .... ......... .... .. .. . 187
Launch Contro l Program .... .. .. .. .. . 112
L eather clean ing/protection ... .. .. ... 2 12
L eaving home .. ..... ...... .. .. .. .. .. 45
Lifting jack ........................ 275
L ift ing vehicle
Light 287
Ambie nce lighting ........... .. .... . 46
Com ing/Leavi ng home ......... ... ... 45
D aytime running lig hts .... .. .. .. .. .. 43
E mergency flashers ....... .. .. .. .. .. 44
E xte rio r lighting ... .... ... .. .. .. .. .. 43
Headlig ht range contro l ... .. .. .. .. .. 4 3
High beam ... ... ..... ... .. .. .. .... 45
Low beam .. ............. .... .. .... 43
Rear fog lights ........... .. .. .. .. .. 43
Side marker lights ........ .. .. .. .. .. 43
Turn signa ls .. ..... ...... .. .. .. .. .. 45
Light/rain sensor Headlights . ............. .... .. .. .. 43
Intermittent (windshield wipers) .. .. .. 48
Sensor defective . . . . . . . . . . . . . . . . . . . . 23 Load
ing the roof rack .. .. .. ... ... .. .. . 62
Locking Power loc king switc h ............... . 36
Remote con trol . . . . . . . . . . . . . . . . . . . . 34
U sing the key .. .. ................. . 36
Low beams
. .. .. .... .......... ...... 43
Lower universal anchorages (Canada) 185
Luggage compartment Cargo ne t . . . . . . . . . . . . . . . . . . . . . . . . . 6S
E nlarging . . . . . . . . . . . . . . . . . . . . . . . . . 64
Loading ... .. .... .. . .. .. ..... ... .. . 63
Movement-activated ope ning . ... .. .. . 38
Ski sack ... .. .. .. .. . .............. . 65
Stow ing luggage ..... ............. 132
Tie-downs . . . . . . . . . . . . . . . . . . . . . . . . . 6S
Lumbar support Front seats . . . . . . . . . . . . . . . . . . . . . . . . 54
M
Maintenance . ....... . .. .. ..... ... .. 292
Malfunction Ind icator Lamp (MIL) . . 21, 29
Manua l shift program ... ............. 111
Massage func tio n
F ron t se ats . . . . . . . . . . . . . . . . . . . . . . . . 54
Matte f inish paint clean ing .......... . 209
Mechanica l key .. .. .. . ... ...... ... .. . 32
Mir ro rs
Adjus ting t he ex ter ior mirrors . . . . . . . . . SO
d' . 1mming .. .. .... .. . .. .. ..... ... .. . 51
Vanity mirrors ... .. . ... ...... ... .. . 47
Monito ring the Advanced Airbag System 157
Mult ifunct ion steer ing whee l .......... . 25
mult itron ic (automatic t ransm ission) . .. 107
N
Natu ra l leather
Cleaning
New tires and wheels
NH TSA
Contacting 212
2S7
134
N igh t vision assistant ............ .. .. 103
Cleaning came ra lenses ......... .. .. 210
N itrogen oxide (NOx) catalyt ic converte r
refer to Ad Blue .......... ......... . 218
Number of seats . .. .... ......... .. .. 136
•
•