"" N
0 ::.,: co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Instruments and warning/indicator lights 17
If the indicator light turns on and the mes
sage appears, there may be limited starting
abi lity.
If th is message turns
off after a litt le while,
the battery charged enough whi le driving.
If the message does not turn
off, have your
authorized Audi dealer or qua lified workshop
correct the malfunction.
~ Engine oil pressure
The red engine oil pressure warning symbol
requires immediate service or repair. Driving
with a Low-oil-pressure indication is Likely to
inflict severe damage to the engine .
• Turn off engine! Oil pressure too low
If the indicator light turns on and the mes
sage appears, the oil pressure is too low.
.,. Pull
off the road.
.,. Stop the vehicle .
.,. Turn
off the engine .
.,. Check the engine oil level ¢ page 216 .
.,. If the engine oil level is too low, add engine
oil ¢
page 216 . Make sure that the oil pres
sure warn ing symbol. appears no longer
in the disp lay before you start driving again.
.,. If the engine oil level is correct and the indi
cator light st ill turns on, turn the engine
off
and do not continue driving. Seek professio
nal assistance.
(l) Tips
- The engine oil pressure symbol. is
not an indicator for a low engine oil lev
el. Do not rely on it. Instead, check the
oil level in your engine at regular inter
vals, preferably each time you refuel,
and always before going on a long trip.
- The yellow oil level warning indication
II requires oil refill or workshop serv·
ice without delay. Do not wait until the
red oil pressure warning. starts to
flash before you respond to the low oil
level warning
l!I. By then , your engine
may already have suffered serious dam
age.
~ Engine oil level
• WARNING: Please add oil immediately
If the indicator light and the message appear,
add engine oil immediately¢
page 214.
II Add oil, max XXXX l. You may cont. driv .
When the symbol l!I and driver message ap
pear, add the amount of oil appearing in the
display at the next opportunity ¢
page 214.
-L Engine cooling system
A malfunction in the engine cooling system
must be repaired as soon as possible.
• Turn off engine and check coolant level
If the indicator light turns on and the mes
sage appears, the coolant temperature is too
high or the coolan t leve l is too low .
.,. Pull
off the road .
.,. Stop the vehicle .
.,. Tu rn
off the engine .
... Check coolant level¢
page 218 .
.,. Add coolant if necessary¢ page 219.
.,. Continue driving on ly after the engine cool
ant warning/indicator light goes out .
.,. Contact your authorized Audi dealer for as-
sistance if necessary.
If the engine coo lant level is correct, then the
radiator fan may be the cause of the malfunc
tion.
• Coolant temperature! Let engine run
with vehicle stationary
If the indicator light turns on and the mes
sage appears, let the engine run at id le for a
f ew m inutes to coo l down .
_& WARNING
-If your vehicle should break down for
mechanical or other reasons, park at a
safe distance from moving traffic, turn
off the eng ine and turn on the hazard
warn ing lights
¢page 51, Emergency
flashers.
-
'"" N
0 ::.,: co ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
Instrument s and warnin g/indic ator ligh ts 19
A WARNING ,~ ~
If the ~ (USA models)/ . (Canada
models) brake system indicator light turns
on together with the ABS and ESC indica
tor lights, the ABS/ESC regulating function
may have failed. Functions that stabilize
t he vehicle are no longer avai lab le. This
cou ld cause the vehicle to swerve and in
crease the risk of sliding . Drive caref ully to
the nearest a uthorized Audi dea ler and
have the malfunction corrected.
(D Tips
For addit ional information on ESC and
ABS, refer to
c::> page 185 .
ABS/(@!) Anti-lock braking system (ABS)
This warning/indicator light monitors the ABS
and the electronic differential lock (EDL).
The warning/indicator light rII:1 (USA mod
els)/ [I] (Ca nada models) w ill come o n for a
few seconds when the ignition is switched on.
The light will go out after an a utomatic chec k
sequence is completed.
There is a malfunction in the ABS when :
- The warning/ indicator lig ht does not illumi
na te when you swi tc h t he ignition on.
- T he warning/i ndicator lig ht does not go out
after a few seconds .
- T he warn ing/ind icator lig ht illuminates
wh ile driving.
T he ESC indicator light also illuminates if
there is a malfunction in the ABS . The mes
sage
Stabilization contro l (ESC) : Fault! See
owner 's manual
also appears in the inst ru
men t clus ter display and a war ning tone
sounds.
Th e brake sy ste m will still respond even
without th e assi stan ce of the ABS sy ste m .
See y our authoriz ed Audi dealer a s soon a s
po ssibl e to re store full braking performan ce .
For more informat ion regarding the ABS
c::> page 185.
Malfunction in the brake system
If the brake war ning l igh t c::> page 15 and the
ABS wa rning illuminate
together there may be
a malfunct ion in the ABS , and there may a lso
be a malfunction in the brake system itself
c::> A . The AB S will not wo rk and you w ill no
tice a change in b raking response and per
formance .
In the event of a malfunction in the brake
s y stem
the warning/indicator light~
(USA mode ls)/ . (Can ada models) in the in
strument cluster flas hes
c::> page 15.
Malfunction in th e electronic diff erential
lock (EDL)
The EDL works together w ith the ABS. The
ABS warning light will come on if there is a malfunction in the EDL system
c::> page 185 .
See your author ized Audi dealer as soon as
poss ible.
A WARNING
- I f the trm (USA mode ls)/ [I] (Canad a
models) warning light does not go ou t,
-
or if it comes on while dr iving, the ABS
system is not wor king p roperly. The vehi
cle can then be stopped only w it h the
standard brakes (without ABS). You w ill
not have the protect ion ABS prov ides.
Contact your authorized Audi dealer as
soon as possible .
-USA models: If the ~ warning light
a nd the
trm warning light come on to
gethe r, the rear wheels could lock up
f ir st under hard bra king. R ear wh eel lock
up can ca use loss of vehicle control and
a n ac cident . H ave yo ur vehicle repaire d
immed iate ly by yo ur authorize d Aud i
dea le r o r qualified works hop. Drive slow
ly and avo id sudden, hard brake applica
tions.
- Canada models: If the brake warning
light . and the ABS warning light
[I]
come on together, the rear wheels could
lock up first under hard braking. Rear
wheel lock-up can cause loss of vehicle
con tro l and an accident. Have your
20 Instruments and warning /indicator lights
vehicle repaired immediately by your au
thorized Audi dealer or qualified work
shop. Drive slowly and avo id sudden,
hard brake applications.
~ J!f Safety systems
The
II (USA models)/ m (Canada models) in
d icator light monitors the safety systems (e .g .
a ir bags, pretensioners) and illuminates for a
few seconds each time you switch the ignition
on.
If the
ffl (USA models)/ EI (Canada models)
indicator light does not go out, or if it illumi
nates whil e you are driv ing, or if it sta rts to
b link , then there is a malf unction somewhere
in the system. If the light does not illuminate
when you switch the ignition on, this also
means there is a ma lfunction.
A WARNING
If you have a malfunction in the safety sys
tems, contact your authorized Audi dealer
immediately . Otherwise the safety sys
tems may not work properly in an acci
dent .
(0) Worn brake pads
Ell Brake pads!
If the warning light illumina tes, immediately
contact your authorized Audi dealer or quali
fied workshop to have all brake pads inspect
ed. On USA models the warning light
Ei'I
comes on together with the warn ing light
1111 -Both sets of b rake pads on an axle
must always be replaced at the same time .
A WARNING
Driving with bad brakes can cause a colli
sion and serious personal injury.
- If the warning light
Ell and the warning
light
11111 ) with the message Brake
pads! comes on in the instrument cluster
l) - : USA mod els only
-
display, immediately contact your au
thorized Audi dealer or qualified work
shop to have all brake pads checked or replaced if necessary.
EPC Electronic power control
This warning/indicator light monitors the
electronic power control.
The ~ warning/indicator light (Electronic
Power Control) illuminates when you switch
the ignition on as a function check.
(D Tips
If this warning/indicator light illuminates
while you are driving, then there is a mal
function in the engine electronics. Have
the malfunct ion corrected as soon as pos
sible by your authorized Audi dealer or a
qualified repair facility.
0 Malfunction Indicator Lamp (MIL)
Th e Ma lfunction Indicator Lamp (MIL) is part
of the On-Board Diagnostic (OBD II) system.
T he symbo l¢• lights up when the ignition is
switched on and will turn off after the engine
has started and has settled at a constant idle
speed. This indicates that the MIL is working
properly.
T he warning light illuminates when there is a
malfunction in the engine electronic system .
Contact your authorized Audi dea ler and have
the malfunction corrected.
An improperly closed fuel filler cap may a lso
cause the MIL light to illuminate
~ page 210.
For more information ~page 29.
!?; Engine speed limitation
Applies to vehicles: with engine speed limitation
(II Do not exceed max. engine speed of
XX.XX rpm
'"" N
0 ::.,: co ,...., \!) ..,.,
,...., ..,., ,....,
Instruments and warning/indicator lights 21
The IJI symbol illuminates when there is an
engine control malfunction. The
[3i indicator
light in the instrument cluster also illumi
nates . The engine speed is limited to the
speed d isplayed in the driver information sys
tem . Keep in mind that the eng ine speed will
not exceed the value displayed in the drive r in
formation system , for example when down
shifting.
Drive to your authorized Aud i dealer immedi
ately to have the malfunct ion corrected.
'l=cr .., Engine oil sensor
• Oil level! Sen sor defective
If the symbol illuminates, contact your au
thor ized Audi dealer and have the o il sensor
i nspected . Until you have th is done, check the
oil level each time you refuel just to be on the
safe side
c::> page 216.
Bil Tank system
mJ Please refuel
If the indicator light turns on for the first
time and the message appears, there are
about 2.1- 2.4 gallons (7 -9 liters) of fuel left
in the tank. Time to refuel
c::> page 209 .
DD Fuel tank system malfunction! Contact
dealer
If the indicator light turns on and th is mes
sage appears, there is a malfunction in the
tank system .
Drive to your authori zed Aud i dealer immedi
ately to have the malfunction corrected.
<:o Windshield washer fluid level
B Please refill washer fluid
If the symbol illumina tes, add windshield
washer fluid to the washer system and also to the headlight washer system *
c::> page 225.
~ Windshield wipers
m Windshield wiper defective
There is a malfunction with the windshie ld
wipers .
Drive to your authorized Audi dealer immed i
ate ly to have the malfunction corrected .
~/ }D 10$ Defective light bulb warning
If the f:I indicator light turns on, a bulb has
failed. Th e message indicates the location of
the bu lb .
- If the
II indicator light also turns on, then
a fog light has failed . The position of the in
dicator light corresponds with the location
on the vehicle .
- If the
IJ indicator light also turns on, then
a rear fog* light has failed . The position of
the indicator light corresponds with the lo
cation on the vehicle.
T his warning can also occ ur if the light switch
is in an unengaged position between two sym
bols.
Vehicle lights : System fault!
If the message appears, there is a malfunc
tion in the headlights or light sw itch.
Drive to your au thorized Audi dealer immedi
ately to have the malfunction corrected .
A WARNING
-Light bulbs a re p ressurized and could ex
plode wh ile they are being changed caus
ing serious personal injury.
- Work with due care when hand ling the
high-voltage section of gas discharge
(xenon) lights*. Failure to do so could re
sult in death or serious injury .
(D Tips
Have the bu lb replaced or the connection
r epaired by your authorized Audi Service
department .
i,0 Headlight range control
Applies to veh icles : w ith headli ght ra nge control
liJ Headlight range control defective !
22 Instruments and warning/indicator lights
If the symbol II illuminates, the dynam ic
headlight range cont rol is no longer wo rking
properly. Have the system checked and re
pa ired at your author iz ed Audi dealer.
~O Adaptive Light
Applies to vehicles: with adaptive light
111 Aud i adaptive l ight: defective
If t he indicator lig ht t urns on a nd th is mes
sage appears, t he re is a ma lfunction in the
adapt ive light system. The headlig hts still
function.
Go to an a uth o rized dea le rship to have the
headlights or the contro l unit for the adapt ive
light repa ired.
~ o Light/rain sensor
Applies to vehicles: with light/rain sensor
£I Automatic headlights/ automatic wipers
defectiv e
If the indicator light t urns on and th is mes
sage appears, the lig ht/ra in sensor is n ot
f u nctioning cor rectly .
For safety reasons the low beams are turned
on permanent ly w ith the switch in AUTO .
H owever, you can c ontinue to turn the lights
on and off using the light switc h. You can still
con trol a ll funct ions tha t are in depe nden t of
the rai n sensor through the wi ndshi eld wipe r
l eve r.
Contact your author ized Audi dealer as soon
as possible to have the prob lem cor rected .
Q Adaptive dampers
Applies to vehicles: with Audi drive select and adaptive
dampers
H Suspension: System fault!
If t he
H symbol in the disp lay comes on,
there is a malfunction in the adaptive damp
e rs . Please go to an authorized Audi dea ler or
qua lified workshop to have the malfu nction
repaired.
I-: Sport differential
Applies to vehicles: with Audi drive select and sport dif
ferential
Sport differential : System fault!
There is a malfunction with t he sport d iffe ren
tia l.
D rive to your au thorized A udi dealer immedi
ate ly to have the ma lfunction corrected.
Sport differential : Overheating
T he trans missio n tempera ture has inc reased
s ignifica ntly due to t he spor ty d riving manner .
Dr ive in a less sporty ma nner until the tem
p era ture re tur ns to the normal range and t he
in dica to r li ght switc he s of.
_& WARNING ... -
Co ntac t your author ized Audi dealer or
qu alified wor kshop if the s port differential
i s faulty or malfunct io ning. T he repair
must be perf ormed by t rained personnel
usi ng the co rrect oil in o rder to ensure
safety.
~ Ignition lock
l3 Ignition lock defective
There is a malfunction in the e lectronic igni
t ion loc k. Please go to a n author ized Audi
dealer or other qualified worksh op to have t he
malfu nction repa ired .
¢ Q Turn signals
Wh eneve r yo u use the left
Ill o r th e r ight 8]
tu rn s ignal, the in dicato r li ght blin ks. W he n
yo u use t he emerge ncy fla she rs, bo th indic a
tor lights flash.
If one of the turn s igna l light bulbs bu rn o ut,
t h e tur n sig nal w ill bli nk twi ce as fast as no r
m al. Ca ref ully dr ive to you r a utho rized Aud i
dealer imme diate ly to have the m alfunction
cor rected.
M N
~ co
rl I.O
"' rl
"' rl
Power opening/closing rear lid
App lies to vehicles: with a utom atic rear li d operatio n
The open position can be adjusted.
Fig. 29 Dr iver's door: Unlock ing the rear lid
-
Fig. 30 Lock ing switch in t he rear lid
Opening rear lid
"" Press the button ~ on the remote key for
at least one second . Or
""Pu ll the unlock button~ in the driver's
door¢
fig. 29. Or
"" Press the handle on the rear lid¢
page 38,
fig . 27.
Closing rear lid
""P ress the close button in the open rear lid
¢
fig. 30. T he rear lid moves to the closed
pos ition by itself and soft close locks it auto
matically ¢
,&...
Saving the opening angle of the rear lid
""Bring the luggage compartment lid into the
desired open position. The position can only
be stored when the lid is above a certain
height.
""P ress and hold the
¢fig. 30 button for at
l east four seconds until the lights blink to
store the desired open position .
Opening and closing 39
""To set a higher open position, wait at least
five seconds and then carefully press the
luggage compartment lid upward.
"" Press and hold the¢
fig. 30 button again for
at leas t four seconds and this will store the
new open position .
The settings in the radio or MMI* determine if
the rear lid can be opened using the handle
¢page 36.
Opening will be stopped immediately when:
- You press the
~ button on the remote con -
trol master key for at least one second, or
- You press the
e:5 button in the rear lid, or
- You push the handle in the rear lid, or
- You pull the~ button in the driver's door,
or
- When someth ing blocks the rea r lid or
makes it difficult for the lid to move .
If you press one of the buttons
~ now, the
rear lid will either open or close, depending on
its angle.
If you pull lightly on its handle, the rear lid
will close.
Closing will be stopped immediate ly when :
- You press the
e:5 button in the rear lid, or
- You push the hand le in the rear lid, or
- You release the~ button on the driver's
door, or
- When something blocks the rear lid or
makes it difficult for the lid to move .
If you press one of the buttons~ now, the
rear lid will either close or open, depending on
its angle.
If you pull lightly on its handl e, the rear lid
will close.
You can manua lly stop the automatic open
ing/closing of the luggage compartment lid.
The automatic closing process begins if you
push down on the rear lid.
M N
~ co
Clear vision Lights
Switching the lights on and off
F ig . 43 Instrument pane l: headlight control switch
Light switch ·'t/,·
Turn the switch c> fig . 43 to the correspond ing
position . When the lights are switched on, the
:oo: symbol turns on.
0 • The lights are off or the dayt ime running
lights are on:
- USA mod els : The daytime running lights are
activated when the light sw itch
c> fig . 43 is
in the
O position or the AUTO position (only
in daylight conditions) . The daytime running
lights function can be turned on and off in
the radio or MMI* menu
E xteri or li ghtin g
¢ page SO, c> &_ .
-Ca nad a mod els: The daytime runn ing lights
are activated when the light sw itch
¢ fig . 43
is in the O position, :oo: position or the AUTO
posit ion (only in daylight conditions). The
daytime running lights function cannot be
turned off¢&. .
AUTO* -Automatic headlights switch on and
off depending on b rightness, for example in
tw ilight, during rain or in tunnels¢,& .
:oo: -Side marker lights
~D -Low beam headlights
Fog light s/rea r fog ligh t(s)*
Press the appropriate button c> fig. 43:
1D -Fog lights
; 0$ -Rear fog light(s)
,...., l/1 ,....,
Clear vi sion 49
adaptive light *
When switched on, adaptive ligh t adap ts to
curves in the road depend ing on the vehicle
speed and the steering ang le. This provides
better lighting through the curve. The system
operates at speeds between approximately 6 mph (10 km/h) and 68 mph (110 km/h).
St atic corner ing light * (vehicles with adaptive
light) -the cornering light switches on at
speeds up to approximately 25 mph (40 km/ h) when a certain steering wheel angle is
reached or when a turn signal is activated. The
area to the s ide of the vehicle is illuminated
better whe n turn ing .
The adaptive light and the cornering light only
function when the switch is in the AUTO posi
tion (automatic headlights*) .
A WARNING
-Daytime running lights and automatic
headlights* are only intended to ass ist
the driver . T hey do no t re lieve the driver
of his responsibility to chec k the head
lights and to t urn them on manua lly ac
cording to the current light and visibility
conditions. For examp le, fog cannot be
detected by the light sensors*. So a lways
switch on the headlights
~D under these
weather conditions and when driving in
the dark .
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists. Always turn on
the head lights so that you can see ahead
and so that others can see your car from
the back.
- Please obey all laws when using the
lig hting sys tems described here.
(D Note
The rear fog lights* should on ly be turned
on in accordance with t raff ic regulation, as
the lights are bright for following traffic. ..,.
50 Clear vis ion
@ Tips
- The light sensor* for headlight control is
located in the rear view m irror mount.
You should therefore not apply any st ick
ers to the windsh ield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted
c> page 50.
- When you remove your key from the igni
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the driv
er's door is open .
- In cool or damp weather, the ins ide of
the headlights, turn signals and tail lights can fog over due to the tempera
ture difference between the inside and
outside. They will clea r shor tly after
switching them on. This does not affect
the service life of the lighting.
- In the even t of a light sensor malfunc
tion, the driver is no tified in the instru
ment cluster disp lay¢
page 22.
Turn signals and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher .
Fig. 44 Tu rn s ig na l and hig h beam lever
Turn sign als ¢i ¢
The turn signals activate when you move the
l ever into a turn s ignal pos ition when the ign i
tion is switched on.
(D -right turn signal
@-left tur n signa l
The turn s ignal blinks three times if you just
tap the lever .
High be ams and headlight flasher [D
Move the lever to the correspon ding posit io n:
@ -high beams on
@ -high beams off or headlight flasher
The indicator light
ii in the instrument cl us
te r turns on .
Notes on thes e features
-The turn signals on ly wor k w ith the ignition
t ur ned on. The indicator ligh ts
Ct or a in
the instrument cluster also blink.
- After you have turned a co rner, the turn s ig
na l switches off au toma tically .
- The
high beam works on ly w hen the head
lights a re on. The ind icator ligh t
II in the
instrument cluster illuminates when the
high beams are on .
- The
headlight flasher works o nly as long as
you ho ld the lever -even if there a re no
lights switched on . The indicator light
II in
the instrument cluster illuminates when you
use the headlight flasher.
A WARNING
--
Do not use the h igh beam or headlight
flasher if you know that these could blind
oncom ing traffic.
Adjusting exterior lighting
The functions ore selected in the radio or
MMI" .
.,. Select: !CARI function button> Exte rior
light ing .
Or
.,. Select: !CARI function button > Car systems *
control button > Vehicle s etting s> Exterior
lighting .
Coming home (light when leav ing car }*,
Leav ing home (light when unlocking car )*
The coming home function illuminates the
area around the vehicle when the ignition is
switched off and th e dr ive r's door is open ed.
Depend ing on veh icle equ ipment, the function
can be switched on and off or the length of
time the lig hts remain on* can be ad justed . ..,.