236 Tires and wheels
unbalanced, resulting in vibrations you can
usually feel through the steering whee l.
Unbalanced wheels must be rebalanced to
avoid excessive wea r on steer ing, suspension
and tires . A wheel must a lso be rebalanced
when a new tire is installed.
Incorrect wheel alignment
I ncorrect wheel alignment can cause exces
sive tire wear, impair ing the safety of the veh i
cle. If tires show excess ive wear, have the
wheel alignment checked by an authorized
Audi dealer or qualified workshop.
All-wheel drive
Vehicles w ith quattro must a lways have tires
of the same size, construction and tread type.
F or details see
<=> page 190 .
A WARNING
Sudden tire failure can lead to loss of con
trol, a crash and ser ious persona l injury!
- Never drive a vehicle when the tread on
any tire is worn down to the wear indica
tors.
- Worn tires are a safety hazard, they do
not grip well on wet roads and increase
your risk of "hydroplaning" and loss of
control.
- Always keep chemicals that can cause
tire damage, such as grease, oil, gasoline
and brake fluid away from t ires.
- Tires age even if they are not being used
and can fail suddenly, especially at high
speeds. Tires that are more than 6 years
old can only be used in an emergency
and then with special care and at lower
speeds.
- Never mount used tires on your vehicle if
you are not sure of their "previous histo
ry." Old used tires may have been dam
aged even though the damage cannot be
seen that can lead to sudden tire failure
and loss o f vehicle control.
New tires and replacing tires and wheels
New tires and wheels have ta be broken in .
Fig. 160 Tire specificat ion codes on the s idewall of a
tire
No. Description
@ Nomina l w idth of t ire in mill imeters
® Ratio of height to width (aspect ratio)
© Radial
® Rim diameter code
® L oad index and speed rating
(J) U.S . DOT tire identification number
® Audi Origina l tire
® Sever snow conditions
@ T ire ply composition and materials
used
@ Maximum load rating
@ Treadwear, traction and temperature
grades
@ Maximum permissible inflation pres-
sure
T he tires and rims are essential parts of the
vehicle 's design . The tires and rims approved
by Audi are spec ially matched to the charac
te ristics of the vehicle and can make a major .,..
252 What do I do n ow ?
-Support the vehicle securely with ap
propriate stands if work is to be per
formed underneath the vehicle;
otherw ise, there is a potential risk for
in Jury .
- To help preven t injury to yourself and
your passengers:
- Do not raise the vehicle u nti l you a re
sure the jack is sec urely e ngaged .
- Passengers mus t not rema in in the ve
h icle when it is jacked up .
- Ma ke sure that passengers wait in a
safe p lace away from the vehicle and
well away from the road and traffic.
- Make sure jack posi tion is co rrect, ad
just as necess ary and then contin ue to
raise the jack .
- Changes in temperature or load can af
fect the height of the vehicle .
0 Note
Do not lift the vehicle by the s ill. Pos ition
the vehicle ja ck only at the designated lift
ing poi nts on the sill. Othe rwise, your vehi
cle will be damaged .
Taking the wheel off/installing the spare
Follow these instructions s tep-by-step for
c hanging the wheel.
Fig . 172 Chang ing a w hee l: u sing th e screw driver ha n
dl e (w it h th e bla de re mov ed) to t urn the bolts
Fig. 173 Ch ang ing a wheel : alignment p in in sid e th e
t op hole
After you have loos ened all wheel bo lts and
raised the vehicle off the ground, remove and
replace the wheel as follows :
Removing the wheel
.,. Use the hexagon al so cket in th e screwdri v
er handle
to completely remove the top
most whee l bolt and set it aside on a
clean
surfac e Q fig. 172 .
.,. Screw the threaded end of the al ignme nt
p in
from the tool k it hand-t ight into t he
empty bol t hole
Q fig . 173.
.,. Then remove the other wheel bolts as de
scr ibed above .
.,. Take off the whee l leaving the a lignment pin
in the bo lt ho le
Q (J) .
Putting on the comp act sp are wheel
.,. Lift the spare whee l and carefully slide it
over the alignment p in to guide it in place
Q (J) .
.,. Use the hexagonal socket i n the screwdriver
handle to screw in and tighten a ll whee l
bolts
slightly .
.,. Remove the alignment pin and insert and
tighten the rema ining whee l bolt slightly
like the rest .
.,. Turn the jack handle counter -clockwise to
lower the vehicle until the jack is fully re
leased .
.,. Use the wheel bolt wrench to tighten all
wheel bo lts fi rmly
Q page 250 . Tighten
them
crosswise , from one bolt to the (ap
proximately) opposite one, to keep the
wheel cente red.
