2015 AUDI A3 CABRIOLET width

104 Audi side assist
General information
A pplies to vehicles: with Audi side assist
®
®
©
Fig. 101 D riving s it u at ions
AU DI
F ig . 102 Rea r of th e ve hicle: pos it io n of t he se nso rs
(exa mple)
Side assist functions at speeds above approx i­
mately 19 mph (30 km/h).
@ Vehicle s that are approaching
In certain cases, a vehicle will be classifie d as
cr itica l for a lane change even if it is still
somewhat far away . The faster a vehicle ap­
proaches, the sooner the display in the e xteri ­
or mirror will tur n on .
@ Vehicle s traveling with you
Vehicles traveling w ith you a re indicated in the
exterior m irror if they are classified as cr itical
for a lane change. All vehicles detected by
side assist are indicated by the time they en­
ter your "blind spot", at the latest .
© Vehicles left behind
If you s low ly pass a ve hicl e th at sid e ass ist has
de te ct ed (t he difference in s peed be tween the
vehicle and you r vehi cle is less than 9 mph or
15 km/ h), the display i n the exterio r mirro r
turns on as soon as the ve hicle enters your
blind spot.
The disp lay wi ll not t urn on if you quickly pass
a ve hicle that s ide assist has detected (t he d if ­
f erence in speed between the ve hicle and your
vehicle is greater than 9 mph or 15 km/h).
Functional limitations
T he ra dar senso rs are designed to detect the
left and right adjacent lanes whe n the road
l anes a re the normal width. I n some sit ua ­
t ions, the d isp lay in the exterior mirror may
tu rn on even thoug h there is no ve hicle locat­
ed in the area that is cr itical fo r a la ne cha nge.
Fo r exampl e:
- If the lanes are nar row or if your a re dr iving
o n t he e dge of your lane. If this is the case ,
the system may have detected the vehicle in
another la ne that is
not adjacent to you r
cur rent lane .
- If you are dr iving th ro u gh a curve . S ide as­
sist may react to a vehicle that is one lane
over from the adj ace nt lane.
- If si de assist reacts to o ther objects (such as
h igh or d is pl ace d gua rd rails) .
- In poor weather conditions. The side assist
fu nctions are limited .
Do not cover the rada r senso rs
c::> fig. 102 with
stickers, depos its, bicycle w heels or other ob­
jects, because this wi ll affect the funct io n. Do
not use s ide ass ist when tow ing a trailer . For
information o n cleaning, r efe r to
c::> page 204 .
&_ WARNING
-Always pay attention to traffic and to the
ar ea arou nd your ve hicl e. Si de a ssis t ca n­
no t repla ce a driver's a tte ntion. The driv­
er a lo ne is always res pons ible fo r lane
ch ang es a nd similar driving ma ne uvers.

230 Tires and wheels
-If you notice unusual vibra­
tion or if the vehicle pulls to
one side when driving, al­
ways stop as soon as it is
safe to do so and check the
wheels and tires for dam­
age.
0 Note
-Please note that summer and winter tires are de­
signed for the conditions
that are typical in those sea­
sons. Audi recommends us­
ing winter tires during the
winter months. Low tem­ peratures significantly de­
crease the elasticity of
summer tires, which affects
traction and braking ability. If summer tires are used
in
very cold temperatures, cracks can form on the tread
bars, resulting in perma­
nent tire damage that can
cause loud driving noise and
unbalanced tires. Audi is not
responsible for this type of
damage.
-Burnished, polished or chromed rims must not be used in winter road condi­
tions. The surface of the
rims does not have suffi­
cient corrosion protection
for this and could be perma­
nently damaged by road salt
or similar substances.
Glossary of tire and loading terminology
Accessory weight
means the combined weight (in
excess of those standard items
which may be replaced) of auto­ matic transmission, power
steering, power brakes, power
windows, power seats, radio, and heater, to the extent that
these items are available as fac­
tory-installed equipment (whether installed or not).
Aspect ratio
means the ratio of the height to
the width of the tire in percent.
Numbers of 55 or lower indi­
cate a low sidewall for im­
proved steering response and
better overall handling on dry
pavement.
...

232 Tires a nd whee ls
Ma ximum load rating
means the load rating for a tire
at the maximum permissible in­
flation pressure for that tire.
Maximum loaded vehicle
weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options weight
Maximum (permissible)
inflation pressure
means the maximum cold infla­
tion pressure to which a tire
may be inflated. Also called
"maximum inflation pressure."
Normal occupant weight
means 150 lbs. (68 k ilograms)
times the number of occupants seated in the vehicle up to the
total seat ing capac ity of your
vehicle.
Occupant distribution
means distribution of occu ­
pants in a vehicle .
Outer diameter
means the overall diameter of
an inflated new tire.
Overall width
means the linear distance be­
tween the ex teriors of the side­
walls of an inflated tire, includ ­
ing elevations due to labeling,
decorations, or protect ive
bands or ribs .
Ply
means a layer of rubber -coated
parallel cords .
Production options weight
means the comb ined we ight of
those installed regular produc­
tion op tions weighing over 5
lbs . (2. 3 kg) in excess of those
standard items which they re ­
place, no t prev iously consid­
ered in curb weight or accessory
weight , incl uding heavy duty
brakes, ride leve lers, roof rac k,
heavy duty bat tery, and spec ial
trim.
Radial ply tire
means a pneumatic tire in
wh ich the p ly c ords that extend
t o the beads are laid at sub ­
stantially 90 degrees to the
centerline of the t read .

M N
" > co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Recommended inflation
pressure
see¢ page 231J Cold tire infla­
tion pressure.
Reinforced tire
means a tire design to operate
at higher loads and at higher
inflation pressures than the
corresponding standard tire. Reinforced tires may be identi­
fied as "XL", "xl", "EXTRA
LOAD", or "RF" on the sidewall.
Rim
means a metal support for a
tire or a tire and tube assembly
upon which the tire beads are
seated.
Rim diameter
means nominal diameter of the
bead seat. If you change your
wheel size, you will have to pur­ chase new ti res to match the
new rim diameter.
Rim size designation
means rim diameter and width.
Rim width
means nominal distance be­
tween rim flanges.
Tires and wheels 233
Sidewall
means that portion of a tire be­
tween the tread and bead.
Speed rating (letter code)
means the speed at which a tire
is designed to be driven for ex­
tended periods of time. The rat­ ings range from 93 mph
(150 km/h) to 186 mph
(298 km/h) ¢
page 251. You
may not find this information
on all tires because it is not re­
quired by law.
The speed rating letter code,
where applicable, is molded on
the tire sidewall and indicates
the maximum permissible road speeds ¢
& in Winter tires on
page 255.
Tire pressure monitoring system
means a system that detects
when one or more of a vehicle's
tires are underinflated and illu ­
minates a low tire pressure
warning telltale.
Tread
means that portion of a tire
that comes into contact with
the road.
' •
•
' •

248 Tires and wheels
A WARNING
Sudden tire failure can lead
to loss of control, a crash and serious personal injury!
-Never drive a vehicle when the tread on any tire is worn down to the wear indica­
tors.
-Worn tires are a safety haz­
ard, they do not grip well on
wet roads and increase your risk of "hydroplaning" and
loss of control.
-Always keep chemicals that
can cause tire damage, such
as grease, oil, gasoline and brake fluid away from tires.
-Tires age even if they are
not being used and can fail
suddenly, especially at high
speeds. Tires that are more
than 6 years old can only be used in an emergency and
then with special care and at lower speeds.
-Never mount used tires on your vehicle if you are not sure of their "previous histo­
ry." Old used tires may have
been damaged even though
the damage cannot be seen
that can lead to sudden tire
-failure and loss of vehicle control.
New tires and replacing
tires and wheels
New tires and wheels have to
be broken in.
Fig. 176 Tire specification codes on
the sidewall of a tire
No. Description
CD Passenger car tire (where
applicable)
@ Nominal width of tire in
millimeters
® Ratio of height to width
(aspect ratio)
@ Radial
® Rim diameter code

250 Tires and wheels
characteristics, and safety of This contains the following in-
the vehicle. The table formation:
(¢ page 235) lists specifica-p Indicates the tire is for pas-
tions of the tires approved for
senger cars (where applica-
the Audi models covered by ble)
your Owner's Literature.
255 Nominal tire width in mm
The tire pressure label located
of the tire from sidewall
on dr iver's side B-pillar
edge to sidewall edge. In
(¢ page 235, fig. 173) lists the
general, the larger the num-
specifications of the original ber, the wider the tire
equipment tires installed on
40 Height/width ratio in per-
your vehicle at the time it was cent (aspect ratio)
manufactured.
R Tire construction: Radial
Federal law requires tire manu-
19 Rim diameter code (in in-
facturers to place standardized ches)
information on the sidewall of
100 Load rating code
all tires
¢fig. 176. This infor-H Speed rating letter code
mation identifies and describes
XL (or "xl", "EXTRA LOAD" or
the fundamental characteris- "RF") Indicates that the tire
tics, the quality grade of the is a "Reinforced" or an
"Extra
tire and also provides a tire Load" tire
identification number for safety
M+S (or "M/5") Indicates that
standard certification and in the tire
has some mud and
case of a recall. snow capability
Tire specifications The
tires could also have the in-
Knowledge of tire specifications formation of direction of rota-
tion
¢ page 229.
makes it easier to choose the
correct tires. Radial tires have
Tire manufacturing date
the tire specifications marked The manufacturing date is also
on the sidewall, for example: indicated on the tire sidewall
255/40 R 19 100 H XL (possibly only on the inner side
of the wheel):
...

254 Tires and wheels
run flat tires. If run flat tires
are used, they must be in­
stalled on all four wheels. Mixing tire types is not per­
mitted.
@) Note
-For technical reasons, it is not generally possible to
use the wheel rims from
other vehicles. This can hold
true for wheels of the same
vehicle type.
- If the spare tire is different
from the tires that you have mounted on your vehicle
(for example winter tires or
wide prof ile tires), then use
the spare tire for a short pe­
riod of time only and drive
with extra care. Replace the
flat tire with the tire match­ ing the others on your vehi­
cle as soon as possible.
- Never drive without the
valve stem cap . The valves
could get damaged.
@) For the sake of the environment
Dispose of old tires in accord­
ance w ith the local require­
ments.
Uniform tire quality grading
- Tread wea r
- Traction AA A B C
- Temperature ABC
Quality g rades can be foun d where applicab le
on the t ire s ide wall between t read sho ulder
and maximum section width
¢ page 248,
fig . 176 .
For example: Tread wear 200 , Traction AA,
Tempera ture A .
All passenge r ca r tir es must con fo rm to Feder ­
al Safety Req uirements in ad dition to these
grades.
Tread wear
T he tread we ar g rade is a c omparative r ati ng
b as ed on the wea r ra te of the tire when tes ted
u nder con tro lled cond itions o n a specifie d
government test course .
F o r ex am ple, a tire gr aded 1 S0 would wear
o n e and one h alf ( 11/ 2) times as well on the
government course as a tire gr aded 10 0 .
T he re lative per forman ce of tires depen ds
up on the actu al cond itions of the ir use, h ow­
ever, and m ay dep art s ignific antly from the
no rm due to va ria tions i n driving ha bits, se rv ­
ice p ractices and differe nces in road c haracter­
ist ics and climate.
Traction
The tr actio n gr ad es, fro m hig hest to lowest,
are AA, A, Ban d
C. Those grades represent t he
ti re 's ability to stop on wet pavement as
measured unde r cont rolled conditions on
specified g overnment test surfaces of aspha lt
and co ncrete. A t ire mar ked C may have poor
traction performance
¢ A .
Temperature
The temperature g rades are A (the highest),
B, an d C, represe nting the tire's resistance to
the generation of heat and its ab ility to dissi­
pate heat when tested unde r controlled condi­
t ions on a specif ied ind oor l abo rato ry test
whee l.

M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
In certain circumstances, you may not use
wheel bo lts from a different vehicle -
even if it
i s the same mode l
Qpage 284.
A WARNING
Improperly tightened or maintained wheel
bolts can become loose caus ing loss of
control, a collision and ser ious personal in­
jury .
- Always keep the wheel bolts and the
threads in the wheel hubs clean so the
wheel bolts can turn easily and be prop­
erly t ightened.
- Never grease or oil the wheel bolts and
the threads in the wheel hubs. They can
become loose w hile d riving if greased or
o iled,
even if tightened to the spec ified
torq ue.
- Only use wheel bo lts that belong to the
rim being ins talled.
- Never use different whee ls bolts on your
vehicle .
- Always maintain the correct tightening
torque fo r the wheel bolts to reduce the
risk of a wheel loss. If the tigh teni ng tor­
que of the wheel bolts is too low, they
can loosen and come out when the vehi­
cle is moving . If the tightening torque is
too high, the whee l bolts and threads
can be damaged and the wheel ca n be­
come loose .
(D Note
The specified torque for the wheel bo lts is
90 ft lb (120 Nm) w ith a tolerance of
± 7,4 ft lb(± 10 Nm). Torque whee l bolts
diagonally. After changing a wheel, the
torque must be checked as soon as possi­
b le with a torque wrench -prefe rably by an
author ized Audi dealer or qualified wo rk­
shop.
Low aspect ratio tires
Your Audi is factory-equipped with low aspect
ratio tires . These tires have been thorough ly
tested and been selected spec ifically for your
model for the ir superb performance, road feel
Tire s an d wheel s 257
and handling under a variety o f driving condi ­
tions. Ask your authorized A udi dealer for
more details .
T he low aspec t ratio of these tires is ind icate d
by a numera l of
55 or le ss in the tire's size
designation. The numera l represents the ratio
of the t ire's sidewa ll height in relation to its
tread width expressed in percentage.
Conven­
tiona l tires have a he ight/w idth rat io of 60 or
more .
The performance of low-a spect-ratio tire s is
particularl y sens it iv e to improper inflation
pressure. It is therefore important that low
a spect ratio tir es are inflated to the specified
pre ssure and that the inflation pr essure i s
regularly checked and ma intain ed . Tire pr es­
s ure s should be checked at lea st on ce a
month and alway s bef ore a long trip
~ page 240 , Checking tire pressure .
A Word about Low Aspect Ratio and High
Performance Ti res
Hig h pe rformance tires are des igned for bet­
ter performance and handling in warm cli­
mates. When driving in cold, snowy or icy
weather, you sho uld equ ip your vehicle w it h
four all-season or winter tires, which
offer
better traction under those condit ions. We
suggest you use the Audi recommended win­
te r or a ll-season tires specified for you r Audi.
High performance tires a lso have a lower as ­
pect ratio that aids performance and han­
dling . Driving over rough or damaged road
surfaces, as well as debr is, cu rbs and other
obstacles can cause serious damage to
whee ls, tires, vehicle body, and suspens ion
parts . B e carefu l to avo id road hazards and re­
du ce your speed , espec ia lly if your vehicle is
equipped wi th low prof ile tires .
Please a lso remember when making your se­
lection that, wh ile these tires deliver respon­
s ive handling, t hey m ay ride less comfo rtably
and make more noise than o thers . Finally,
these tires may wear more quickly than other
c h oices.
IJJ>
•
•
•