24 Instruments and indicator lamps
Drive to an authorized Audi dea le r o r author
ized Audi Service Facility immediate ly to have
the malfunction corrected.
@ For the sake of the environment
Fuel should never enter the sewer system
or come into contact with the ground.
@ Tips
More info rmation on refueling is available
on page
i:!>poge 211.
~ Washer fluid level
1- ) Please add washer fluid
Fill the washer fluid with the ign ition switched
off ¢
page 22 7.
6 Windshield wipers
m Windshield wiper: system fault!
There is a malfunct ion with the w indshield
wipers.
Drive to an authorized Aud i dealer or author
ized Audi Service Facility immed iate ly to have
the ma lf uncti on corrected .
~ Defective light bulb warning
Applies to vehicles: with driver informatio n system
If the J:i indicator light turns on, a bulb has
failed. The message indicates the location of
the bulb .
Replace the bulb immed iately.
Vehicle lights: system fault!
There is a malfunction in the headlights or
light switch . Drive to an authorized Audi deal
er or authorized Audi Service Facility immedi
ately to have the malfunction corrected.
A WARNING
-
- Light bulbs are under pressure and can
exp lode when bulbs are replaced -risk of
injury. -
With gas-discharge lamps* (xenon head
lights), the high-voltage component
must be handled appropriately. Other
wise, there is a risk of fatal injury .
i,ID Dynamic headlight range control
system
Applies to vehicles: with Xenon lights
II Headlight range control system: system
fault!
There is a malfunction in the dynamic head
li ght range control system, which may cause
glare for other drivers.
Drive to an authorized Audi dealer or author
ized Audi Serv ice Facility immediately to have
the malfunction corrected.
go Audi adaptive light
Applies to vehicles: with Audi adaptive light
&fl Audi adaptive light: system fault!
There is a malfunction in the adapt ive lights .
The headlights still function .
Drive to an authori zed Audi dealer or author
ized Audi Service Facility immediately to have
the malfunction corrected .
@:> Light/rain sensor
Applies to vehicles : with light/rain sensor
El Automatic hea dlights: system fault!
t!I Automatic wipers: system fault!
The light/rain sensor is not working.
For safety reasons, the low beams are turned
on permanently with the switch in
AUTO. You
can continue to turn the lights on and off us
ing the light switch. You can still contro l all
wiper funct ions that are independent of the
rain sensor .
Drive to an authorized Audi dealer or author
ized Audi Service Facility immediately to have
the malfunction corrected .
M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Q Adaptive dampers
Applies to vehicles: with Audi drive select
R Suspen sion : system fault!
There is an adaptive damper malfunction .
Drive to an aut horized Aud i dea le r or a uthor
i zed A udi Service Facility immed iate ly to have
the ma lfunction corrected .
¢¢Turn signals
If the B or B ind icator light b links, a turn
sig nal is tu rned on . If both indica to r li ghts are
b linki ng , the eme rgency flashers a re on .
In an indicator light bli nks twice as fast as
usual then a b linker bu lb has fai led. Carefully
d rive to an au thorized Aud i deale r or autho r
iz ed A udi Service Fac ility i mmed iate ly to have
the m alfu nction co rrec ted .
@ Tips
For mo re i nfo rmation on the tur n sig nals,
refer to
9 page 5 1.
Instruments and indicator lamps 25
•
26 Driver information system
Driver information
system
Overview
Ap plies to vehicles: with d river in format ion syste m
Fig. 9 Instrument cluster: driver informat ion system
(example)
Data is automatically recorded, processed and
d isplayed in the driver information system.
Sett ings for special equipment can be adjust
ed in the MMI. Select the
I MENU ! button> Car
> Systems* menu control button .
Introduction
The driver information system is controlled
through the multifunction steering wheel
c::;, page 2 7, fig. 10.
The driver information system c;, fig. 9 con
tains the following information:
- @ Tab (register)
-@ Vehicle information
-© Status line (se lector lever posi tion, out-
s ide temperaturec:=;,
page 11)
-@ On-board compute r
The following functions are possible, depend ing on vehicle equipment: @
®
First tab ~ Vehicle
functions:
On-board computer, time, date
c:=;,page 27
Efficiency program
c:=;,page28
Digital tachometer
Assistance systems
Audi adaptive cruise control*
¢page87
Audi active lane ass ist*
¢page99
Reduced display
Second
tJ. 6 Driver messages and ind ica-
tab tor lights
c,,..c Service interval display
c:=;,pag
e 13
Third fl I I Audio/ i»> radio
tab
F ourth .,..,.
Telephone*
tab
Fifth tab
~I~ Navigation*
The second tab is only visible if at least one in
dicator light or message is shown or if that
system is switched on .
Display
In the driver information system you will see:
Radio station or CD
Time and date
¢page 10
Odometer, trip odometer ¢page 11
Outside air temperature ¢page 11
Service interval display c::;, page 13
Indicator lights and messag-¢page 13
es
Digital tachometer
Cruise control system
c:=;,page 85
Speed warn ing c:=;,page 84
Selector lever positions c::;, page 110
On-board computer display c::;, page 27 ...
....,
N
r--. > co
rl I.O
"' rl
"' rl
Other equipment
Applies to vehicles: with driver information system
F ig. 13 Instrument cluster : other equ ipment (exam
p le)
~ Turn the menu thumbwheel@Qpage 27,
fig. 10 while in the efficiency program until
t h e other eq uipme nt affect ing consump tion
appears .
Other equipmen t that is curren tly affecting
fuel cons umption is listed in t he eff iciency
p rog ram. The display shows up to three other
items of equipment @. The equipment using
the most f uel is listed first . If more than three
items using fue l are switched on, the equip
ment that is currently using the most fuel is
d isplayed .
A scale @ also shows the current total con
sumpt ion of all other equipment.
Fuel economy messages
App lies to vehicles: with driver information system
Fi g. 14 Instrument cluster : economy tip (examp le)
F ue l economy messages are disp layed when
fuel consumption is inc reased by certain con
ditions. If yo u follo w these fuel economy mes
sages, you can reduce your vehicle's consump
tion of fuel. The messages appear automati cally and are o nly displayed in the eff ic iency
Dr iver in formation system 29
program . The fue l economy messages t urn off
automatica lly after a certain period of time.
~ To tu rn an e conomy me ssage off immed iate
ly a fter it appea rs, press any bu tton on the
m ultifunction stee ring wheel.
(D Tips
- O nce yo u have turned a f uel economy
mess age off, it will o nly appear ag ain a f
ter yo u turn the ign ition on again.
- Th e fu el economy mess ages are no t dis
played in every instance, but rather in in
tervals over a period of time .
On-Board Diagnostic
system (OBD)
System indicator light (MIL)
The system indicator ligh t (M IL) ¢.§ in the in
str ument cl uster is part of the On Board Diag
nostic System (OBD II).
T he warni ng/i ndicator light t urns on when the
ignition is sw itched on and t urns off once the
engine is sta rted and is runn ing in id le at a
stab le speed. This indicates that the MIL is
funct ioning correct ly.
If the light does not turn off after sta rting
the engine
or turns on while driving, t his may
indicate there is a ma lfunction in the engine.
If the indicator turns on, the cata lytic convert
er may be damaged .
Drive
with reduced engine performance
(avoid high speeds for extended periods of
time and/or fast acceleration) and have the
malfunction corrected. See an authorized Audi
dealer or author ized Audi Service Facility.
The indicator may turn on if the electronic
speed limiter is faulty. For addit ional informa
tion, refer to Q
page 30, Electronic speed
limiter* .
The MIL may also turn on if the fuel filler cap
is not closed cor rectly
q page 212.
M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Switchin g th e ig nition on /off
"'T o sw itch the ignition on, turn the ignition
key to position
(D .
"'To switch the ignition off, turn the ignition
key to position @.
Starting the engin e
Your vehicle is equipped w ith launch cont ro l.
As soon as you have turned the ign ition key to
position @, the engine will start automatical
l y.
"' Press the brake peda l and move the se lector
lever to the P or N pos it ion.
"'T urn the key briefly to position @. The igni
t ion key automatically r eturns to posit ion
(D . Do not press the accelerator pedal wh en
doing this .
Major electrical equipment switches off tem
porarily when starting the eng ine.
If the engine does not sta rt immedia tely , stop
the starting procedure by turning the ignition key to position @and repeat after 30 sec
onds .
Automatic start m alfunction
If the ~ indicator l ight turns on (gasoline en
g ine) and the message
Engin e start sys te m
m alfu nction. Ple ase contac t Se rvice
appears ,
there is an automatic start ma lfunction.
To start t he eng ine, hold the ignition key in
position @until the engine runs .
Drive to an authorized Aud i dealer or author
ized Audi Service Facility immed iate ly to have
the ma lfunction corrected .
_& WARNING
-Never allow the engine to run in confined
spaces -there is a risk o f asphyxiation.
- Never remove the ign ition key from the
ignition lock whi le the vehicle is moving .
Otherw ise the steering lock wi ll engage
and you will not be able to steer the vehi
cle.
- Please note that the brake booster and
power steering only work when the en-
Dri vin g 77
gine is running. When the engine off, you
must use more force to steer or brake
the vehicle. Because the usual steering
and brak ing capability is not avai lab le,
the risk of accidents or injur ies increases.
- Always take the vehicle key with you
when leaving the vehicle, even for a
short period of time. This applies part ic
ularly when children remain in the veh i
cle. Otherwise the ch ild ren could start
the engine or operate electrical equip
men t such as power w indows.
(D Note
- Avo id h igh engine speed, full throttle,
and heavy eng ine load as long as the en
gine has no t reached operat ing tempera
t u re yet . You could damage the engine.
- T he engine cannot be started by pushi ng
or towing.
(® For the sake of the environment
Do not let the eng ine run w hile pa rked to
warm u p. Begin driv ing immediately . T his
r educes unne cessary emissions.
(D Tips
- If it is d iff icult to turn the key to position
(D , turn the steering wheel back and
forth slightly to release the s teer ing
wheel lock .
- After s tarting a cold engine, there may
be a brief period of inc reased no ise be
cause the oil press ure must first bui ld up
in the hydraulic va lve adj usters . This is
normal and not a cause for concern.
- If the battery is disconnected and recon
nected, you have to hold the ignition key
in posit ion
(D for five seconds for the en
gine to start.
- After sw itching the ignition off, you can
only remove the key when the selector
lever is in the "P" (Park) position. After
that, the selector lever is locked.
•
M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Switchin g th e ig nition on /off
If the> ,:r- u indicator l ight blinks and the mes
sage
Ple ase move s teering wheel appea rs
when switching the ignition on, the steering is locked by th e steering lock. In this case, turn
the steering wheel slight ly to the left/ right.
.. To switch the ignition on or
off, press the
I S TAR T ENG INE S T OPI button. Do not press
the brake pedal whil e doing this .
Starting the engin e
Your vehicle is equipped with launch cont ro l.
The engine starts automa tically when you
press the
I S T AR T ENG INE S T OP I button brief
l y.
.. Press the brake peda l and move the se lector
lever to the P or N pos ition .
.. Press the
I STAR T ENGINE STOP I button
briefly . The eng ine will star t.
Majo r electrical equ ipment switches
off tem
porarily when starting the eng ine .
I f the engine does not start immediately , stop
the starting procedu re by push ing the
I S TAR T ENGINE ST OP ! button again and re
peat after 30 seconds .
Automatic start m alfunction
If the Ila indicator l ight turns on (gasoline en
g ine) when you start the engine, there is an
automatic sta rt malfunction .
To start the eng ine, press and hold the
!STAR T ENGIN E STOP ! button until the eng ine
runs.
Drive to an authorized Aud i dealer or author
i z ed Audi Service Fac ility immed iately to have
the malfunction corrected .
A WARNING
-Never allow the engine to ru n in confined
spaces -there is a r isk of asphyxiation.
- Always take the veh icle key with you
when leaving the vehicle, even for a
short per iod of t ime . This applies partic
ularly when chi ldren remain in the vehi
cle . Otherwise the children could start
Dri vin g 79
the engine or operate electrical equip
ment such as power w indows.
- Please note that the brake booster and
power steering only work when the en
gine is running. When the engine
off, you
must use more force to steer or brake
the vehicle . Because the usual steer ing
and brak ing capability is not avai lable,
the risk of accidents or injur ies increases .
(D Note
-Avo id h igh engine speed, full throttle,
and heavy eng ine load as long as the en
gine has not reached operat ing tempera
ture yet. You could damage the engine .
- The engine cannot be started by pushing
or towing .
@ For the sake of the environment
Do not let the eng ine run wh ile parked to
warm up . Begin dr iv ing immediately . Th is
reduces unnecessary emissions .
(D Tips
-After starting a cold engine, there may
be a brief period of increased no ise be
cause the oil press ure must f irst bu ild up
in the hydraulic va lve ad justers. This is
normal and not a cause for concern.
- If the . indicator light blinks in the in
st rument cluste r before switching the ig
nition
off, the ignit ion wi ll not switch on
again .
qpoge 192
- If you leave your vehi cle wit h the ignition
switched on, the ign it ion w ill switch
off
after a certain amount of time . Make
sure that electrical equipment such as
the exterior lights are switched
off .
T · th · ff using the
button
App lies to vehicles: wit h convenience key
.. Bring the veh icle to a full stop .
.. Move the se lector lever into the P posit ion .
.. Press the
I STA RT E NGINE ST OP ! button
q page 78, fig. 80. ..,.
•
82 Driving
Electromechanical
parking brake
Operating
The electromechanical parking brake replaces
the hand brake.
Fig. 82 Ce nter conso le: Park ing brake
~ Pull the switch@~ fig. 82 to set the park
ing brake . The . (USA models)/ . (Cana
da models) indicator lights in the button
and in the instrument cluster display turn
on .
~ To release the parking brake, press the brake
or acce le rator pedal while the ignit ion is
switched on and press the button @at the
same time. The. (USA models)
I. (Can
ada models) indicator lights in the button
and in the display turn off .
Your veh icle is eq uipped with an electrome
chanical parking brake. The parking brake is
designed to prevent the vehicle from rolling unintentionally and replaces the hand brake.
I n addition to the normal functions of a tradi
tional hand brake, the electromechanical parking brake provides various convenience
and safety functions.
When starting from a stop
- T he integral hill start assist helps you when
dr iving by automatically releasing the park
ing brake ~
page 83, Starting from a
stop .
-When starting on inclines, the hill start as
sist prevents the vehicle from unintentional
l y rolling back. The braking force of the
parking brake is not released until sufficient driving force has been built up at the
wheels.
Emergency brake function
An emergency braking functions ensu res that
the vehicle can be slowed down even if the
normal brakes fail~ page 84, Emergency
braking function.
_.&. WARNING
- Do not press the accelerator pedal inad
vertently when the vehicle is stationary
and the engine is running and a gear is
selected. Otherwise the vehicle will start
to move immediately and could result in
a crash .
- If the power supply fails, the released
parking brake can no longer engage . In
this case, park the vehicle on leve l
g round and secure it by placing these
lecto r lever in the P position. See an au
thorized Audi dealer or authorized Audi
Service Facility for assistance.
(D Note
If the. or. (USA models) I. (Cana
da models) indicator light in the instru
ment cluster blinks, there is a malfunction
i n the brake system. Refer to the detai led
description of the indicator lights
~page 18.
- If the . (USA models) I. (Cana-
da models) or
Ill indicator light turns
on, there is a malfunction in the parking
brake
c> page 19.
(D Tips
- If the electromechanica l parking brake is
set while the ignition is switched off, the
¢@'A indicator light in the button and in
the instrument cluster dis-
play . (USA models) /. (Cana-
da models) will turn off after a certain
amount of time.
- If driver's door is opened while the igni
tion is switched on, the park ing brake
sets automatically. This prevents unin
tended rolling of the vehicle.
....,
N
r--. > co
rl I.O
"' rl
"' rl
Setting the driving program
Applies to vehicles: with Audi adaptive cruise control
A adaptive cruise con trol dr iving program is
adjustable on vehicles witho ut Audi dr ive se
l ect* .
• Select in the MMI: the
I MENU I button > Car
> Systems * control button > Driver assis
tance > Adaptive cruise control> Driving
program > Comfort/Standard/Dynamic.
Selecting the driving mode
Applies to vehicles: with Audi adaptive cruise co ntrol
The adaptive cruise contro l driving program is
ad justab le for veh icles w ith Audi drive se lect
using the driving mode.
• Select the desired driving mode
Comfort,
Auto , Dynamic or Individual *
with the knob
Qpage 107 .
Request for driver intervention
Applies to vehicles: with Audi adaptive cruise co ntrol
Fig. 93 Inst rumen t cluster: dr iver inte rve ntion reques t
In some s ituations, the braking from the
adaptive cruise control system is not enough
to maintain enough distance to the object
ahead . In these s ituations, the system will re
quest you to take action .
The . indicator light and the graphic in the
display wi ll wa rn yo u about the danger
Q fig. 93. You will a lso hear an aud io signa l.
Press the brake pedal to s low your vehicle
down.
Audi adaptive cruise control 93
Driver messages
Applies to vehicles: wit h Aud i adapt ive c ru ise control
IIJ ACC: unavailable
The system cannot guarantee that it will de
tect objects correctly and is switched off. The
sensor was moved or is faulty. Drive to your
authorized Aud i dea ler or a uthorized Audi
service facility immediately to have the mal
function corrected.
fl ACC: currently unavailable. No sensor vi
sion
fl ACC and Audi pre sense: currently un·
available. No sensor vision No sensor visio n
This message appears if the sensor v iew is ob
structed, for example by leaves, snow, heavy
spray or dirt. Clean the sensor
Q page 87,
fig. 84.
Ill ACC: currently unavailable . Gradient too
steep
The road exceeds the maximum possible an
gle for safe adaptive cruise control operat ion.
The adaptive cru ise control cannot be switch
ed on.
Ill ACC: only available in D, Sor M
Select the D/S or M selector lever position.
Ill ACC: parking brake applied
The adaptive cru ise control system switches
off automatically if the parking b rake is set .
The adaptive cruise control is available again
after re leas ing the parking brake.
Ill ACC : currently unavailable . Stabilization
control input
This message appears if the Electronic Stabili
zation Control (ESC) is taking action to stab i
lize the veh icle . In this case, adapt ive cru ise
control switches off automat ica lly.
Ill ACC off: manual control!
This message appears if the vehicle rolls back
when starting on a s light incline, even though
ACC is active. Press the brake pedal to prevent
the vehicle from rolling or starting to move.
1111-